AIDA
GELINA
BRIKEN
nToF
CRIB
ISOLDE
CIRCE
nTOFCapture
DESPEC
DTAS
EDI_PSA
179Ta
CARME
StellarModelling
DCF
K40
AIDA
Draft saved at 00:00:00
Fields marked with
*
are required
Entry time:
Thu Apr 25 13:15:37 2024
Author
*
:
Subject
*
:
@ CAEN N1419 Set programmable parameters - see CAEN N1419 manual p.16 (attachment 1) INTERLOCK = CLOSED CONTROL = REMOTE Set front panel switches HV on/off/kill = ON No interlock jumpers @ AIDA server From a command terminal, login to nnrpi1 using ssh, set device permissions, and launch putty. ssh -X nnrpi1 -l npg password: : : : % sudo chmod 777 /dev/ttyUSB2 % putty & From the putty window sequentially select 'USB2', 'load' and 'open' - this will select and load a saved serial session for device /dev/ttyUSB2 and launch a command terminal for the serial session. Enter the command 'caen' followed by return. Note the command is not echoed. The CAEN HV interface should appear. Enter the command 'd' to display/modify parameters. See CAEN N1419 manual pp.27-29 for further commands. See attachment 2. N.B. The above procedure assumes: /dev/ttyUSB0 = USB-controlled ac mains switch (device pl2303) /dev/ttyUSB1 = serial link to FEE64 system console (device FT232RL) /dev/ttyUSB2 = CAEN N1419 (device FT232BM) However, these assignments may vary. You can use the command dmesg to check assignments. For example, % dmesg | grep usb [ 1.178926] usbcore: registered new interface driver usbfs [ 1.184722] usbcore: registered new interface driver hub [ 1.190218] usbcore: registered new device driver usb [ 1.568604] usbcore: registered new interface driver smsc95xx [ 2.065233] dwc_otg bcm2708_usb: DWC OTG Controller [ 2.075294] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1 [ 2.087646] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000 [ 2.115566] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.127464] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.139731] usb usb1: Product: DWC OTG Controller [ 2.149477] usb usb1: Manufacturer: Linux 3.18.7+ dwc_otg_hcd [ 2.160291] usb usb1: SerialNumber: bcm2708_usb [ 2.190521] usbcore: registered new interface driver usb-storage [ 2.348492] usbcore: registered new interface driver usbhid [ 2.360241] usbhid: USB HID core driver [ 2.677666] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 2.897985] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 2.910008] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.217656] usb 1-1.1: new high-speed USB device number 3 using dwc_otg [ 3.327968] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 3.340138] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.422390] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:0b:f6:73 [ 3.517666] usb 1-1.3: new full-speed USB device number 4 using dwc_otg [ 3.630124] usb 1-1.3: New USB device found, idVendor=067b, idProduct=2303 [ 3.642534] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.655514] usb 1-1.3: Product: USB-Serial Controller D [ 3.666257] usb 1-1.3: Manufacturer: Prolific Technology Inc. [ 3.761138] usb 1-1.4: new low-speed USB device number 5 using dwc_otg [ 3.894746] usb 1-1.4: New USB device found, idVendor=046d, idProduct=c016 [ 3.908414] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.922059] usb 1-1.4: Product: Optical USB Mouse [ 3.933904] usb 1-1.4: Manufacturer: Logitech [ 3.955374] input: Logitech Optical USB Mouse as /devices/platform/bcm2708_usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C016.0001/input/input0 [ 3.976035] hid-generic 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-bcm2708_usb-1.4/input0 [ 4.087698] usb 1-1.5: new low-speed USB device number 6 using dwc_otg [ 4.343360] usb 1-1.5: New USB device found, idVendor=04f2, idProduct=0402 [ 4.359726] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.377627] usb 1-1.5: Product: USB Keyboard [ 4.377641] usb 1-1.5: Manufacturer: Chicony [ 4.456521] input: Chicony USB Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.5/1-1.5:1.0/0003:04F2:0402.0002/input/input1 [ 4.475410] hid-generic 0003:04F2:0402.0002: input,hidraw1: USB HID v1.11 Keyboard [Chicony USB Keyboard] on usb-bcm2708_usb-1.5/input0 [ 4.634626] input: Chicony USB Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.5/1-1.5:1.1/0003:04F2:0402.0003/input/input2 [ 4.657391] hid-generic 0003:04F2:0402.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Chicony USB Keyboard] on usb-bcm2708_usb-1.5/input1 [ 7.431307] usbcore: registered new interface driver usbserial [ 7.659127] usbcore: registered new interface driver usbserial_generic [ 7.806673] usbserial: USB Serial support registered for generic [ 8.078137] usbcore: registered new interface driver pl2303 [ 8.408967] usbserial: USB Serial support registered for pl2303 [ 9.088988] usb 1-1.3: pl2303 converter now attached to ttyUSB0 <- FEE64 console [ 13.617763] usb 1-1.2: new high-speed USB device number 7 using dwc_otg [ 13.749727] usb 1-1.2: New USB device found, idVendor=05e3, idProduct=0608 [ 13.775541] usb 1-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 13.807792] usb 1-1.2: Product: USB2.0 Hub [ 20.127979] usb 1-1.2.2: new full-speed USB device number 8 using dwc_otg [ 20.294212] usb 1-1.2.2: New USB device found, idVendor=0403, idProduct=6001 [ 20.323567] usb 1-1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 20.357627] usb 1-1.2.2: Product: FT232R USB UART [ 20.397680] usb 1-1.2.2: Manufacturer: FTDI [ 20.415415] usb 1-1.2.2: SerialNumber: A801LOA8 [ 20.542107] usbcore: registered new interface driver ftdi_sio [ 20.569826] usbserial: USB Serial support registered for FTDI USB Serial Device [ 20.628458] usb 1-1.2.2: Detected FT232RL [ 20.651619] usb 1-1.2.2: FTDI USB Serial Device converter now attached to ttyUSB1 <- ac mains switch [ 23.708086] usb 1-1.2.3: new full-speed USB device number 9 using dwc_otg [ 23.824265] usb 1-1.2.3: New USB device found, idVendor=0403, idProduct=6001 [ 23.824306] usb 1-1.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 23.824326] usb 1-1.2.3: Product: USB <-> Serial [ 23.824346] usb 1-1.2.3: Manufacturer: FTDI [ 23.833176] usb 1-1.2.3: Detected FT232BM [ 23.834515] usb 1-1.2.3: FTDI USB Serial Device converter now attached to ttyUSB2 <- CAEN N1419 [ 775.531187] ftdi_sio ttyUSB2: usb_serial_generic_read_bulk_callback - urb stopped: -32 [ 775.531296] ftdi_sio ttyUSB2: usb_serial_generic_read_bulk_callback - urb stopped: -32 [ 775.705443] usb 1-1.2.3: USB disconnect, device number 9 [ 780.036554] usb 1-1.2.3: new full-speed USB device number 10 using dwc_otg [ 780.153082] usb 1-1.2.3: New USB device found, idVendor=0403, idProduct=6001 [ 780.153150] usb 1-1.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 780.153174] usb 1-1.2.3: Product: USB <-> Serial [ 780.153193] usb 1-1.2.3: Manufacturer: FTDI [ 780.167981] usb 1-1.2.3: Detected FT232BM [ 780.169356] usb 1-1.2.3: FTDI USB Serial Device converter now attached to ttyUSB2 <- CAEN N1419 [ 2364.526816] ftdi_sio ttyUSB2: usb_serial_generic_read_bulk_callback - urb stopped: -32 [ 2364.526982] ftdi_sio ttyUSB2: usb_serial_generic_read_bulk_callback - urb stopped: -32 [ 2364.657165] usb 1-1.2.3: USB disconnect, device number 10 [ 2365.657499] usb 1-1.2.3: new full-speed USB device number 11 using dwc_otg [ 2365.774075] usb 1-1.2.3: New USB device found, idVendor=0403, idProduct=6001 [ 2365.774116] usb 1-1.2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2365.774142] usb 1-1.2.3: Product: USB <-> Serial [ 2365.774268] usb 1-1.2.3: Manufacturer: FTDI [ 2365.788695] usb 1-1.2.3: Detected FT232BM [ 2365.790604] usb 1-1.2.3: FTDI USB Serial Device converter now attached to ttyUSB2 <- CAEN N1419 If using >1 CAEN N1419 check the output of the command 'demsg usb' for FT232BM devices and identify the USB device numbers. You should then set the device permissions for *each* /dev/ttyUSB[n] and start a putty session for *each* CAEN N1419 module. You can distinguish CAEN N1419 modules by the address (Addr) label shown in the CAEN display.
Encoding
:
HTML
ELCode
plain
Suppress Email notification
Attachment 1:
Drop attachments here...
Draft saved at 00:00:00
ELOG V3.1.4-unknown