AIDA GELINA BRIKEN nToF CRIB ISOLDE CIRCE nTOFCapture DESPEC DTAS EDI_PSA 179Ta CARME StellarModelling DCF K40
  CARME  ELOG logo
Message ID: 25     Entry time: Mon Oct 5 08:21:40 2020
Author: CB (remotely), JM 
Subject: First bake of CARME with pumps (cont.) 
5 OCTOBER

08:21 Temperatures stable overnight. See attached. Baking continues.
Remember to visually inspect the tent for potential new drafts the next time in Daresbury.
Also remember to check on thermocouple 1-4 status / position.

10:15 Draft caused by section of top blanket collapsing slightly producing a hole at the top-back end of the volume. Only way to remove draft is to power down and shift 
some of the larger blanket sections over to support the collapsed bit. Keith requires temperatures >120C for the vessel average to proceed so heat was powered down and 
jacket reconstructed. See attached photos of the top of the baking volume (Sorry for quality).

Pressure on vessel when baking concluded: 2e-7mbar

13:00 Baking jacket all sorted, temperature set to 60C to equilibrate. New session had to be started as cooling then heating confuses the rates on the baking program. All 
looks good at the moment, will continue to monitor and increase temperature when needed. Automatic mode may be able to be utilised again as rectifying the insulation on 
the 
back has reduced the thermal gradients somewhat. 

Pressure on vessel when baking restarted: 1e-8 mbar
Bumax order has also been delivered

16:00 Monitoring remotely, bakeout has been on automatic for an hour and is currently at 67C. Vessel gradient ~7.5C

17:15 All looks okay, will leave for a few hours now. Temp is 73C, gradient ~8.2C

22:00 Automatic baking to 90C gradient >10C. Ramped to 105C for RE72-1 and 100C for RE72-2. Will leave overnight to stabilise

6 October

9:50 Temperatures stable, increasing to 115C, 105C 

11:20 Temperatures stable, Increasing to 120C, 115C

13:15 Temperatures stable, increasing to 125C, 120C. Vessel average ~115C. 

14:45 Temperatures stable (see attached). Increasing to 130C, 125C. Vessel average~120C

20:16 Temperatures stable, may be getting to edge of how hot we can get. Increasing to 135C, 130C overnight. Vessel average~128C should be sufficient.

7 October

07:30 Temperatures stable, have reached max temperature we can achieve 132C, 128C on RE-72 thermocouples. Vessel average~131C should be sufficient. Temperatures will be 
maintained until Monday when negs can be activated. 

20:30 Temperatures stable (see attached)

8 October

10:30 Temperatures stable

9 October 

8:30 Temoeratures remain stable 
Attachment 1: 20201005_0821_temps.png  78 kB  Uploaded Mon Oct 5 09:22:54 2020  | Hide | Hide all
20201005_0821_temps.png
Attachment 2: 20201005_110422.jpg  1.137 MB  Uploaded Mon Oct 5 15:00:42 2020  | Hide | Hide all
20201005_110422.jpg
Attachment 3: 20201005_134003.jpg  1.009 MB  Uploaded Mon Oct 5 15:01:02 2020  | Hide | Hide all
20201005_134003.jpg
Attachment 4: temps3.png  192 kB  Uploaded Mon Oct 5 18:15:31 2020  | Hide | Hide all
temps3.png
Attachment 5: temp4.png  435 kB  Uploaded Tue Oct 6 15:46:36 2020  | Hide | Hide all
temp4.png
Attachment 6: temp5.png  160 kB  Uploaded Wed Oct 7 21:40:31 2020  | Hide | Hide all
temp5.png
ELOG V3.1.4-unknown