Beam energy - 1.361 MeV/u

17:12

Run 28 Started - beam on target

Detectors IN (left arm pot = 36.5 mm, right arm pot = 70.5 mm)

Beam position (vertical offset -9mm, horizontal offset -7.5mm)

Ions circulate in the ring for 3 seconds before they are dumped. Total time between injections is 12 seconds.

Target density apporx 4.2e11 atoms/cm2, pressures in the ring are below 1e-10 mbar. (Attachment 1+2)

Leakage current plot (attachment 3) - change in leakage current is consistent with temperature variation from ML online plot.

18:18

FEE temperatures OK - aida09 is slightly hot - 65.06 C so slightly above vertex temp value of 65C and stays this way over several reloads (attachment 4)

System wide checks OK

Statistics (attachments 5+6) - aida09 and aida12 slightly high stats but still <1K. Check load does not resolve.

Tape server OK - writing ~730 kB/sec

Merger OK

Monitoring code XY plots and Ey energy histograms (attachments 7+8)

18:53 All checks OK

21:58

All system checks ok. Temperatures and leakage current ok. Merger ok.

Attatchment 9: Rates and stats - all below 1k

Attatchment 10: Temperatures

Attatchment 11-14: Waveforms layouts 1,2,7,8 respectively look okay

Attatchment 15: Leakge current

Attatchment 16: lowenergyXY plots

Vacuum pressure is ok.

23:01

system wide checks ok. Temperatures ok. Leakage current ok. Merger ok all went green. Waveforms same as 10pm check.

Statistics - aida09 and aida12 went over 1k (attach 17), but reloaded and settled down again seconds appart (attatch 18). Reloaded again at 23:14 and stats were aove 1k again (attatch 19).

Attatchment 20 is the leakage current, still ok. 

Vacuum pressure ok (attatchment 21) - rises after small bump down from the regular value.

01:00

System wide checks ok. Temperatures ok. Leakage current ok (see attatchment 22). Merger ok all went green. Waveforms the same as 10pm check.

Statistics - aida09 and aida12 occasionally just over 1k when reloading a few times, but goes below mostly.

Vacuum pressure ok, stablised after small bump around 10ish (attatchment 23)

03:00

Ring vacuum suffered from long-term creep, especially in YR08. Tweaked nozzle position. Pressure improves, target density slightly affected. Attachment 24-25

Leakage current and temperature indicate we have an increase in temperature in the ring. This is confirmed by vacplot. Attachment 26-27

Merger continues OK 28

Rates and Stats show we have no beam. Going to the lab 29-30.

R28_22 NO BEAM

03:45

No beam in the ring, we are missing all the spills. Called HKR.

Detectors out in case beam manipulation is required.

Stat plot looked OK. 31

04:35

DAQ continues OK on run R28_24, still no beam

Temperatures slightly lower - OK

System wide checks - OK

Stats - OK

Merger - OK

05:44

Beam is back. It had been away since 1:30 am due to a fault in the new EC power supply. Fault reason unclear.

Detectors back in (left 36.54, right 70.49 mm)

R28_26 BEAM ON

(Beam likely off from R28_ 21-25 inclusive)

Temps as before

Stats now OK - att 32

Merger OK - att 33, 34

Stat spectra OK - att 35. Note slope in ASICS (Rutherford?)

Leakage current trending up - likely temperature related.

Ring pressure OK

Gas target 4.14E11

Beam at injection around 7.5E6. Could be higher. Asked for optimisation later today assuming current configuration holds.

06:59

Temperatures OK

System checks OK

Stats looking good in all FEEs except aida01 and aida15

Leakage current has levelled off - looks OK

Ring pressure looks OK and is trending down - target density 4.1e11

Merger and tape server OK

08:30

System checks all OK

Temperatures OK

Merger / tape server OK - data being written R28_29

Target density 4.1e11, ring pressure stable

09:00

Attachment 38 Spectrum browser stats for all FEEs (log scale)

Attachment 39-42 Spectrum browser *L histograms for select channels for each detector. MIDAS data is consistent with inline monitoring plots.

System checks OK

Beam still on - target density and ring pressure remain stable

11:28 We have access to the voltage dividers for the electron cooler. The voltage is -763.625 V. This corresponds to an electron energy of 746.795 eV and a beam energy of 1.361 MeV/u  using ML ion calc.

This is above the resonance energy of 1.3435 MeV/u. We will now end the run and set the cooler voltage to this ion energy.

Run ended. Run 29 started while setting beam energy.