AIDA
GELINA
BRIKEN
nToF
CRIB
ISOLDE
CIRCE
nTOFCapture
DESPEC
DTAS
EDI_PSA
179Ta
CARME
StellarModelling
DCF
K40
CARME
Draft saved at 00:00:00
Fields marked with
*
are required
Entry time:
Sun Nov 9 00:26:25 2025
Author
*
:
Subject
*
:
> > - water flow/interlock checks > check water flow to/from inflow/outflow manifolds > check all coolant lines to all FEE64s are connected > check USB-controlled ac mains relay 'water' LED illuminated water flow and dew point sensor interlocks OK > > - carme-gsi network cabling > from patch panel YR10/2 > yellow network cable to carme-gsi operating in 19" rack room (2.033) > green network cable to carme-gsi operating in counting room (2.034) > > - boot carme-gsi > systemctl start dhcpd start DHCP dynamic network configuration > ssh -L 8080:proxy.gsi.de:8080 carme@atppc025 establish proxy port for AnyDesk access > ssh -X pi@nnrpi1 > /MIDAS/TclHttpd/linux-arm/TclHttpd-server & start MIDAS server > ssh -X pi@nnrpi1 > ./caen_screen.sh start CAEN N1419ET control interface > > - enable current logging > open a new terminal > ssh pi@nnrpi1 > cd Programs/caenlogger > caenlogger --config caenlogger_config_gsi.toml > > open a new terminal > cd Programs/caenlogger > gnuplot plot_current.gp > > - system log > sudo tail -f /var/log/messages monitor system log e.g. filesystem mounts for FEE64 embedded processors > (sudo does not work - use su instead. will have to fix) > > - FEE64 power ON > Start browser on nnrpi1:8015 > Power On > > - Start MIDAS > select server start icon (leftmost) 1x terminal session will appear > Start browser tab localhost:8015 > > Data Acquisition Control Services > Update (nothing should change) > > Act on all Data acquisition server TICKED > RESET > SETUP > > Enable histograms and waveforms > > Open ASIC control > Act on all FEE64 modules > Act on all ASICS > System functions -> Check ASIC control > > Check FEE64 temperatures (Reload) > > System wide checks > Clock > ADC Calibration > White Rabbit > Drop down -> collect FPGA errors > Check FPGA > Synchronise ASIC clocks > > FADC Align & Check - all FEE64s > Drop down -> calibrate ADCs > System wide checks > Clock > ADC calibration > If any FEE fails, FADC calibrate it again > > DAQ GO > > WR timestamp check WR timestamp monotonically increases aida01->aida16 > > > To startup Merger and Tape Server > > DAQ STOP > > 8115 server, tape server, merger -> from buttons on top > 3x terminal sessions will appear > > Start browser tab localhost:8115 > New Merge control > Tape Service > NetVar Service > > Merger tab > (top) setup > go (ignore error message) > enable output to data storage Merger State = GOing : merge/running : xfer Links => Merger => Storage > > tape server > Inquire Available Devices > Allocate Device > > Enter volume name (if already defined) > Mount volume > Reload > Set run number > Open file > > Open a new terminal > Navigate to /TapeData/ and the volume name > watch ls -lht > > Enable data transfer #1 (in Run Control) > X should appear next to every FEE > > > Check netvar variable NetVar.MERGE.RunOptions = 1 > > DAQ GO > check merger rate and activity of all FEE64s > check tape server blocks written number is increasing > Server state -> Go
Encoding
:
HTML
ELCode
plain
Suppress Email notification
Attachment 1:
Drop attachments here...
Draft saved at 00:00:00
ELOG V3.1.3-7933898