| |
ID |
Date |
Author |
Subject |
|
|
101
|
Fri Jun 7 08:47:17 2019 |
Jorge, Alvaro, Tom, Sunghan, Ale | Co source, test of AIDA/TAS syncronization |
Start: 16:50
Stop: 17:28
Root: 201906071728_60Co_AIDA_in.root
Comment: 60Co source on top of AIDA (red box, key 3). It is positioned on a plastic ruler in the center of the DTAS.
File Number Aida: R18 (_0 should not be used, reset of the time stamp was done during this file). R18_1 started at 16:57, last file R18_4
File Number DTAS: 245,247
201906071650_60Co_AIDA_245.dlt,... 201906071650_60Co_AIDA_247.dlt
After checking the shifts in gain, it seems that for most of the detectors the dynode and anode signal moved in the same direction with the exception of detector 13 (dynode and anode do not move
equally, so probably there is a cable problem here, probably in the Dynode 13 or preamp problem)
Edit 13/06/19 Oscar Hall
The low energy channels of AIDA have been gain matched. Attached is the energy plot of the x and y side strops in AIDA. |
| Attachment 1: 201906071728_60Co_AIDA_in.root
|
| Attachment 2: Screenshot_from_2019-06-07_17-09-21.png
|
|
| Attachment 3: gainMatchSi.png
|
|
|
|
57
|
Mon May 27 08:26:20 2019 |
A. Algora | Co source on top of Aida |
Start: 16:28
Stop: 17:03
Rates: 14.4 kHz (Dinodes), 12.8 kHz (Anodes)
Lmd: 60Co_source_AIDA_201905271627_196.dlt .... 60Co_source_AIDA_201905271627_209.dlt
Root: 201905271703_60Co_AIDA_in.root
Comments: AIDA in, sligthly less deeper than before. It is 17 mm less deeper. So from the other side we measure 17.7 mm to the nose of AIDa.
The source is on top of AIDA with a help of a plastic ruler, that it is lying on top of it. The other extreme of the ruler is attached with tape to the edge
of the frame on the beam side. The source is positioned on top of the detectors 3, and 4, in practical terms in the geometrical center, but on top of
AIDA. 60Co source from source box (key 3). No sources around, the sources are kept inside BELEN. |
| Attachment 1: 201905271703_60Co_AIDA_in.root
|
|
|
20
|
Mon May 20 07:07:59 2019 |
A. Algora | Co source (CD 395) |
Start: 15:10
Stop: 16:08
Positioned in the center, with the source holder.
List mode files: Co60_source_201905201510_030.dlt ... Co60_source_201905201510_034.dlt
Root file: 201905201608_60Co.root
Source: 60Co, red box, source number: CD395. 1 mm plastic (density 1.23 g/cm3)
Rates:
Dynodes: 20.5 kHz
Anodes: 12.5 kHz
|
| Attachment 1: 201905201608_60Co.root
|
|
|
17
|
Mon May 20 06:04:41 2019 |
A. Algora | Co and Cs short file |
Short file with the strong Co source and Cs source. To test stability
Start:11:32
Stop: 14:04
Root file: 201905201404_137Cs60Co_calib.root
Rates; 53 kHz (Dynodes), 47 kHz (anodes) So thresholds should be checked
Anode 12 (calibrated) has a large jump, because the cable in the digitizer was not fully plugged.
We need to recalibrate them. The alignment was done originally with Dynodes. |
| Attachment 1: Screenshot_from_2019-05-20_14-07-24.png
|
|
| Attachment 2: Screenshot_from_2019-05-20_14-14-15.png
|
|
| Attachment 3: Screenshot_from_2019-05-20_14-14-57.png
|
|
| Attachment 4: Screenshot_from_2019-05-20_14-15-39.png
|
|
|
|
112
|
Mon Jun 10 10:01:17 2019 |
Jose, Ale | Co and Cs for new calibration |
Start: 17:57 ?
Stop:18:15
Comment: We put Co and Cs on top of each other below AIDA in the center of the DTAS with the help of the plastic
ruler.
Root: 20190610_1815_60Co_137Cs_AIDA_in.root
To calibrate use the
[dacq@IFICdaq DRikenPreparation]$ root -l
root [0] .L calibrateEFIR_new.cxx
root [3] calibrateEFIR("20190610_1815_60Co_137Cs_AIDA_in.root")
An01_EFIR 306750 536250 606750
An02_EFIR 281250 489750 554250
An03_EFIR 282750 491250 557250
An04_EFIR 263250 458250 518250
An05_EFIR 270750 471750 534750
An06_EFIR 308250 537750 609750
An07_EFIR 290250 506250 572250
An08_EFIR 284250 495750 560250
An11_EFIR 365250 636750 722250
An12_EFIR 263250 459750 521250
An13_EFIR 321750 560250 635250
An14_EFIR 327750 572250 648750
An15_EFIR 300750 522750 591750
An16_EFIR 287250 500250 567750
An17_EFIR 296250 516750 585750
An18_EFIR 273750 479250 542250
Dy01_EFIR 34296.9 59765.6 67578.1
Dy02_EFIR 33828.1 59140.6 66953.1
Dy03_EFIR 34140.6 59296.9 67109.4
Dy04_EFIR 34140.6 59453.1 67265.6
Dy05_EFIR 34453.1 59921.9 67890.6
Dy06_EFIR 34140.6 59453.1 67421.9
Dy07_EFIR 34453.1 60078.1 68046.9
Dy08_EFIR 33828.1 59140.6 66796.9
Dy11_EFIR 34453.1 60078.1 68203.1
Dy12_EFIR 34296.9 59765.6 67890.6
Dy13_EFIR 34296.9 59765.6 67578.1
Dy14_EFIR 34296.9 59921.9 67890.6
Dy15_EFIR 34140.6 59765.6 67578.1
Dy16_EFIR 34296.9 59765.6 67578.1
Dy17_EFIR 34296.9 59921.9 67734.4
Dy18_EFIR 33984.4 59453.1 67265.6
An01_EFIR 306750 536250 606750 0.00223435 -23.9647
An02_EFIR 281250 489750 554250 0.00245634 -29.3018
An03_EFIR 282750 491250 557250 0.00244617 -29.701
An04_EFIR 263250 458250 518250 0.0026289 -30.6075
An05_EFIR 270750 471750 534750 0.00254201 -26.4752
An06_EFIR 308250 537750 609750 0.00222596 -24.3613
An07_EFIR 290250 506250 572250 0.00237623 -28.3674
An08_EFIR 284250 495750 560250 0.00242761 -28.7476
An11_EFIR 365250 636750 722250 0.00188032 -24.9273
An12_EFIR 263250 459750 521250 0.00260091 -22.9409
An13_EFIR 321750 560250 635250 0.00214105 -27.0487
An14_EFIR 327750 572250 648750 0.00209042 -23.3901
An15_EFIR 300750 522750 591750 0.00230503 -31.6127
An16_EFIR 287250 500250 567750 0.002394 -25.7022
An17_EFIR 296250 516750 585750 0.00231789 -24.9283
An18_EFIR 273750 479250 542250 0.00249619 -21.9428
Dy01_EFIR 34296.9 59765.6 67578.1 0.020139 -29.3045
Dy02_EFIR 33828.1 59140.6 66953.1 0.0202412 -23.2189
Dy03_EFIR 34140.6 59296.9 67109.4 0.0203445 -32.9624
Dy04_EFIR 34140.6 59453.1 67265.6 0.0202412 -29.5443
Dy05_EFIR 34453.1 59921.9 67890.6 0.020068 -29.6613
Dy06_EFIR 34140.6 59453.1 67421.9 0.0201694 -26.741
Dy07_EFIR 34453.1 60078.1 68046.9 0.0199676 -26.3096
Dy08_EFIR 33828.1 59140.6 66796.9 0.020313 -25.9882
Dy11_EFIR 34453.1 60078.1 68203.1 0.0198974 -23.544
Dy12_EFIR 34296.9 59765.6 67890.6 0.0199969 -23.7359
Dy13_EFIR 34296.9 59765.6 67578.1 0.020139 -29.3045
Dy14_EFIR 34296.9 59921.9 67890.6 0.0199676 -23.1897
Dy15_EFIR 34140.6 59765.6 67578.1 0.0200376 -22.8024
Dy16_EFIR 34296.9 59765.6 67578.1 0.020139 -29.3045
Dy17_EFIR 34296.9 59921.9 67734.4 0.0200376 -25.9333
Dy18_EFIR 33984.4 59453.1 67265.6 0.020139 -23.0111 |
|
|
16
|
Mon May 20 03:18:03 2019 |
A. Algora | Co and Cs after two days |
We have been running with Co and Cs for the weekend to check the overall stability.
Seems that the detectors did not move too much. Please note that the Ref detector was plugged incorrectly in channel 8
instead of channel 10 of the ancilliary card. A new run will be done to include the reference detector.
It looks that the calibration might be sligthly shifted for detectors 12, 13,17 (Dynodes) |
|
|
27
|
Tue May 21 06:12:13 2019 |
A. Algora | Co again, to have a root file, source CD395 |
Start: 14:11
Stop: 15:01
Lmd: Co60_source_201905211411_055.dlt ...Co60_source_201905211411_058.dlt
Root: 201905211501_60Co.root
Rates: 13.8 kHz (Dynodes), 12.4 kHz (anodes)
Source details: Taken from the red box. No CD395, 1 mm plastic (1.23 g/cm3)
338.4 kBq (1 July 1990). Type ASSET81 to drawing VZ-477/1E
Root file tested and attached |
| Attachment 1: 201905211501_60Co.root
|
|
|
87
|
Sat Jun 1 08:25:47 2019 |
A. Algora | Background, without and with beam |
Start: 16:26
Stop: 17:20 (until then no beam),
Root1: 201906011720_background_AIDA_in.root (no beam, saved 17:20), nor erased
Root2: 201906011729_background_AIDA_in.root (no beam, saved 17:29), nor erased
Root3:201906011741_background_AIDA_in.root (no beam, saved 17:41), nor erased
Root4: 201906011800_background_AIDA_in.root (with beam at the end, saved 18:00), not erased
Comment: At the begining there was no beam, to see the difference. The lead bricks blocking the way to AIDA has been removed as well as the
polyethylene blocks. The lead wall after F11 plastic remains, and of course the lead shielding and the polyethylene shielding before the DTAS is not removed.
Only the blocks that were inside the holes were removed.
Beam arrived around 17:47, intensity at F7 is 3.3 kHz, at F11 of the order of 2.4 kHz, at Aida plastic of the order of 2 kHz after substracting. The beam is centered at 102Sn, but there are a lot of other staff comming through
the noise level.
The increase in the counting rate of the NaI is very small.
Rates with NO BEAM: Dynodes 1.6 kHz, Anodes 1.9 kHz
Rates with BEAM: Dynodes 1.7 kHz, Anodes 1.9 kHz
File with guaranted no beam saved at 17:20 (201906011720_background_AIDA_in.root)
Another one saved at 17:29 (201906011729_background_AIDA_in.root), no beam also, still waiting, similarly saved at 17:41
Attachment 7 shows the rates of TF11PL (black), TCryA (blue), and TAIDAPL (the other color ?). it shows the "noise" level of the AIDA PL, and the increase in the counting
rate of the crystals.
|
| Attachment 1: 201906011720_background_AIDA_in.root
|
| Attachment 2: 20190601_Conf.xlsx
|
| Attachment 3: 201906011729_background_AIDA_in.root
|
| Attachment 4: 201906011800_background_AIDA_in.root
|
| Attachment 5: Screenshot_from_2019-06-01_17-49-05.png
|
|
| Attachment 6: Screenshot_from_2019-06-01_18-04-02.png
|
|
| Attachment 7: Screenshot_from_2019-06-01_18-41-05.png
|
|
|
|
58
|
Mon May 27 09:12:22 2019 |
A. Algora | Background, with AIDA |
Start: 17:13
Stop: 18:03
Rates: 1.8 kHz (Dynodes), 1.8 kHz Anodes
Lmd: Background_AIDA_201905271711_210.dlt ... Background_AIDA_201905271711_226.dlt
Root: 201905271803_background_AIDA_in.root
Comments: AIDA in, in the same conditions as the earlier entry. Some asymetry in the spectra is seen. See EDy05 vs EDy15 and similarly EDy03 vs EDy13 |
| Attachment 1: Screenshot_from_2019-05-27_17-50-45.png
|
|
| Attachment 2: Screenshot_from_2019-05-27_17-51-02.png
|
|
| Attachment 3: 201905271803_background_AIDA_in.root
|
|
|
50
|
Sat May 25 03:42:12 2019 |
A. Algora | Background, no sources around, Aida out |
Start: 11:42
Stop: 14:45
Lmd: Background_201905251141_182.dlt ..Background_201905251141_186.dlt
Root: 201905251445_background.root
Comments: No sources around. All were taken back. Only doubful sources might be there, that I need to ask Nishimura san.
AIDA is out |
| Attachment 1: 201905251445_background.root
|
|
|
61
|
Mon May 27 13:58:03 2019 |
A. Algora | Background, no lmd, AIDA in, no sources around |
Start: 21:59
Stop: 13:15 (next day, 28/05)
Rates: 1.9-2.3 (dynodes), 1.8-1.9 kHz (anodes)
Root: 201905281315_background_AIDA_in.root
Comments: Aida inside. No sources around |
| Attachment 1: 201905281315_background_AIDA_in.root
|
|
|
71
|
Wed May 29 10:01:10 2019 |
A. Algora | Background, no lmd, AIDA in |
Start: 18:02
Stop: 18:33, partial file (201905291833_background_AIDA_in.root), Stop: 09:53 saved also next day (30/05) 201905300953_background_AIDA_in.root
Comments: AIDA in, Bigrips is doing settings (105Te to my best knowledge). There is a lead wall before our setting. No apparent change in the rate of background
Root: 201905300953_background_AIDA_in.root
|
| Attachment 1: 201905291833_background_AIDA_in.root
|
| Attachment 2: 201905300953_background_AIDA_in.root
|
|
|
65
|
Tue May 28 07:49:51 2019 |
A. Algora | Background, no lmd |
Start: 15:50
Stop: 10:09 (next day)
Root: 201905291009_background_AIDA_in.root
Comments: background, Aida in |
|
|
51
|
Sat May 25 06:53:35 2019 |
A. Algora | Background, no dlt files, last config file |
Start: 14:53 (May 25)
Stop: 14: 37 (May 27)
Root: 201905271437_background.root
Comment: there is small assymetry between one side and the other. Probably it is determined by the closeness of the big wall in the direction of the beam |
| Attachment 1: 20190525_Conf.xlsx
|
|
|
92
|
Mon Jun 3 01:45:31 2019 |
A. Algora | Background, no beam for a period |
Start: 09:45
Stop (partial save): 09:55, 10:00, 10:14,10:29,10:37,10:46
Root: 201906030955_background_AIDA_in.root (no beam, not erased), 201906031000_background_AIDA_in.root (no beam, not erased),
201906031014_background_AIDA_in.root(no beam, not erased), 201906031029_background_AIDA_in.root(no beam, not erased),
201906031037_background_AIDA_in.root(no beam, not erased),201906031046_background_AIDA_in.root(no beam, not erased)
201906031135_background_AIDA_in.root (with beam at the end)
At 10:43 or so, a Synch pulse was sent
Intensity of the beam has been increased. There is a clear increase of the background. Rates 3.2 kHz (dynodes), 3.3 (anodes).
9 kHz at F11 plastic, 9 kHz at F7 |
|
|
78
|
Thu May 30 08:57:34 2019 |
A. Algora | Background, no beam + beam, file not saved |
Start: 16:57
Stop:
Comments: first part no beam, but later with beam
Root: File not saved |
|
|
86
|
Sat Jun 1 07:59:20 2019 |
A. Algora | Background, no beam |
Start: approximate 15:54
Stop: 16:23
Root: 201906011624_background_AIDA_in.root
Comment: No beam. AIDA in place
|
| Attachment 1: 201906011624_background_AIDA_in.root
|
|
|
73
|
Thu May 30 02:44:56 2019 |
A. Algora | Background, just a test |
Start: 11:01
Stop: 13:37
Root: 201905301337_background_AIDA_in.root
Comments: Some of the TAC spectra have desapeared with the new configuration file. To be explored.
I have tried with both configuration files that were sent. |
| Attachment 1: 20190530_Conf.xlsx
|
|
|
82
|
Fri May 31 07:03:37 2019 |
A. Algora | Background, beam on, rates at F11PL and AIDAPL |
Start: 15:04
Stop: partial (17:43), 201905311743_background_AIDA_in.root (file corrupt again), system will be restarted
Root:
Comment: Figure shows the rate of F11PLR (black), F11PLL (lighter color, ??) and AIDAPL (blue). There are different counting rates in left and right of F11 plastic |
| Attachment 1: Screenshot_from_2019-05-31_17-36-38.png
|
|
|
|
95
|
Mon Jun 3 12:59:31 2019 |
A. Algora | Background, beam on, 102Sn coulex |
Start: 21:00
Stop: 14:24 (next day)
Root: 201906041423_background_AIDA_in.root
Comments: Beam on, rate at F7 8.9 kHz, the beam was stopped before 14:00 to change the plastic detectors at F3, F7, they are burning them |
| Attachment 1: 201906041423_background_AIDA_in.root
|