| ID |
Date |
Author |
Subject |
|
79
|
Fri Nov 10 01:29:51 2017 |
ASM, MD, DK | run 75 |
Header: 4.7 MeV/u and C_09. PS back, but need to check how much beam actually there was before next issue
Ender: no beam at our sample; IHS cavity (part of normal conducting linac) tripped
====================================================
Run number : 75
Date : 10/11
Start time : 02:20:11
Stop time : 02:41:21
Trigger rate (MIDAS) :
Blocks written : 77
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Run Scalars (approx rates)
0- Ungated : 2
1- Gated : 2
2- dE : 7
3- E : 2
4- HI : 2
5- Pulser : 967
6- Clock : 0
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Beam energy : 4.7 MeV/u
Beam intensity : 2.0-2.5 pA (in the beginning)
Target : C_09 (Pos #5 - 82.44mm), chosen due to similar thickness as CH2_30+25, as used before
Ladder position : 82.44
HI Degrader foil (um) : 15 um Al
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
del_E voltage (V) : -32
del_E leakage (uA) : 0.8
E voltage (V) : -350
E leakage (uA) : 1.75
E_hi voltage (V) : -14
E_hi leakage (uA) : 0.88
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
PA power (upstream, positive) : 1.55A
PA power (upstream, negative) : 0.55A
PA power (downstream, positive) : 0.8A
PA power (downstream, negative) : 0.28A
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Pressure (IMG1) : 6.8E-06
Pressure (old gauge) : 1.9E-05
Pressure (SEC) : 3.8E-06
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Temp (Chiller) : -10.1
Temp (chamber) : 5.4 (from before)
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Comments: realised no beam on target after couple of minutes: normal conducting cavity tripped
Alex and Daid try to fix it.
==================================================== |
|
97
|
Sat Nov 11 05:49:00 2017 |
AM & MD | run 88 |
Header: 3.99 MeV/u and CH2_30+25.
Ender:
====================================================
Run number : 88
Date : 11/11/17
Start time : 06:49:09
Stop time : 07:34:34
Trigger rate (MIDAS) : 0
Blocks written : 1
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Run Scalars (approx rates)
0- Ungated : 0 (or near as damn it)
1- Gated : 0
2- dE : 138k
3- E : 56
4- HI : 15
5- Pulser : 2
6- Clock : 968
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Beam energy (MeV/u) : 3.99 MeV/u
Beam intensity (epA) : ~ 0.1 pA (yes!)
Target : CH2_30+25 (Pos#6; 490-520 ug/cm2)
Ladder position (mm) : 67.26
HI Degrader foil (um) : 10 um Al
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
del_E voltage (V) : -40
del_E leakage (uA) : 0.65
E voltage (V) : -350
E leakage (uA) : 2.11
E_hi voltage (V) : -14
E_hi leakage (uA) : 2.42
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
PA power (Up, positive) (A) : 1.55
PA power (Up, negative) (A) : -0.55
PA power (Down, positive) (A) : 0.8
PA power (Down, negative) (A) : -0.28
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Pressure (IMG1) (mbar) : 7.8 E-06
Pressure (old gauge) (mbar) : 2.35 E-05
Pressure (SEC) (mbar) : 4.3 E-06
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Temp (Chiller) deg : -10.1
Temp (chamber) deg : 5.7
覧覧覧覧覧覧覧覧覧覧覧覧覧覧覧
Comments: Laser needs cleaning - person (Dima) on the way. Right now, very low beam current. Stopped when Dima arrived
==================================================== |
|
14
|
Fri Sep 8 19:03:23 2017 |
TD | w26 network configuration |
Network configuration files for workstation w26 (Sun Ultra 45)
serial # 0743TFC0DQ
host ID # 840e6006
MAC address 0:14:4f:e:60:6
The MIDAS DAQ configured to use ppc1 (MVME 2431 CPU) connected
to w26 via port 1 (/dev/bge1) |
| Attachment 1: hosts
|
#
# Internet host table
#
#
# Merged entries from ipnodes into hosts on <Wednesday April 2 18:57:41 BST 2008>
# Backup files saved in /etc/inet/ directory: hosts.premerge, ipnodes.premerge
#
127.0.0.1 localhost
129.215.73.26 w26 loghost egmsg
192.168.1.25 w26daq
192.168.1.1 ppc0 # TUDA Motorola MVME 2431 CPU
192.168.1.2 ppc1 #
192.168.1.3 ppc2 #
192.168.1.4 ppc3
192.168.1.5 ppc4
192.168.1.6 ppc5
192.168.1.7 ppc6
|
| Attachment 2: ethers
|
08:00:3e:2b:59:76 ppc0 # TRIUMF, TUDA
00:01:af:0b:11:22 ppc1 # HIE-ISOLDE, CERN
00:01:af:0b:10:7a ppc2 # u/s
00:01:af:09:86:88 ppc3 # GELINA, JRC IRMM
00:01:af:08:2c:38 ppc4
00:01:af:09:df:db ppc5 # Edinburgh
00:01:af:09:86:83 ppc6 # u/s
|
| Attachment 3: netmasks
|
#
# The netmasks file associates Internet Protocol (IP) address
# masks with IP network numbers.
#
# network-number netmask
#
# The term network-number refers to a number obtained from the Internet Network
# Information Center.
#
# Both the network-number and the netmasks are specified in
# "decimal dot" notation, e.g:
#
# 128.32.0.0 255.255.255.0
#
129.215.72.0 255.255.252.0
192.168.1.0 255.255.255.0
|
| Attachment 4: nsswitch.conf
|
#
# Copyright 2006 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
#
# ident "@(#)nsswitch.files 1.14 06/05/03 SMI"
#
# /etc/nsswitch.files:
#
# An example file that could be copied over to /etc/nsswitch.conf; it
# does not use any naming service.
#
# "hosts:" and "services:" in this file are used only if the
# /etc/netconfig file has a "-" for nametoaddr_libs of "inet" transports.
passwd: files
group: files
hosts: files
ipnodes: files
networks: files
protocols: files
rpc: files
ethers: files
netmasks: files
bootparams: files
publickey: files
# At present there isn't a 'files' backend for netgroup; the system will
# figure it out pretty quickly, and won't use netgroups at all.
netgroup: files
automount: files
aliases: files
services: files
printers: user files
auth_attr: files
prof_attr: files
project: files
tnrhtp: files
tnrhdb: files
|
| Attachment 5: hostname.bge0
|
w26
|
| Attachment 6: hostname6.bge0
|
|
| Attachment 7: hostname.bge1
|
w26daq
|
| Attachment 8: hostname6.bge1
|
|
| Attachment 9: defaultrouter
|
129.215.75.254
|
| Attachment 10: dfstab
|
# Place share(1M) commands here for automatic execution
# on entering init state 3.
#
# Issue the command '/etc/init.d/nfs.server start' to run the NFS
# daemon processes and the share commands, after adding the very
# first entry to this file.
#
# share [-F fstype] [ -o options] [-d "<text>"] <pathname> [resource]
# .e.g,
# share -F nfs -o rw=engineering -d "home dirs" /export/home2
share -F nfs -o rw=np-suns /scratch
share -F nfs -o rw=ppc1,root=ppc1 /MIDAS
|
| Attachment 11: hosts.allow
|
rpcbind: 192.168.1.0/255.255.255.0
in.tftpd: 192.168.1.0/255.255.255.0
rpcbind: 129.215.72.0/255.255.252.0
rpcbind: 255.255.255.255 0.0.0.0
sshd: .gsi.de .ed.ac.uk .dl.ac.uk .cern.ch @np-suns
|
| Attachment 12: hosts.deny
|
ALL: ALL: spawn (/usr/sfw/sbin/safe_finger -l @%h | /bin/mailx -s %d-%h td) &: DENY
|