| ID |
Date |
Author |
Subject |
|
398
|
Sat Oct 22 02:32:37 2016 |
TD | Saturday 22 October | 10.32 DAQ found stopped, no merger error messages
Most recent file R70_315, last accessed 06.46
R70_315 ADC data synchronised
DSSSD bias & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
System-wide checks - SYNC errors & SYNC pulses fail - other checks OK - see attachments 4-7
AIDA SYNC stats - see attachment 8
Restart merger OK
DAQ STOP OK
DAQ RESET & SETUP OK
ReSYNC OK
System-wide checks OK
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
10.42 DAQ starts (R71)
18.25 DAQ stop OK
System wide test all OK *except* SYNC errors - see attachments 8-11
New SYNC error baseline
18.54 Repeat system wide checks whilst DAQ is still halted - SYNC errors *and* SYNC pulse now fail - see
attachments 12-15
This may suggest that the clock signal itself is affected by LN2 fill cycle
DAQ RESET & SETUP OK
ReSYNC OK
System-wide checks OK
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
18.59 DAQ starts (R72)
nnaida15 drops data transfer #1 tag at DAQ GO
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
19.07 DAQ starts (R73)
19.17 DAQ stalled
Restart merger OK
DAQ STOP OK
Syten wide checks - SYNC error and SYNC pulse fail - dissimilar FEE64 counts in SYNC pulse
DAQ RESET & SETUP OK
ReSYNC OK
System-wide checks OK
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
19.37 DAQ starts (R74)
|
|
874
|
Sat Jul 22 08:17:48 2023 |
TD | Saturday 22 July | 09.20 CAEN N1419ET
Floating outputs
Channel #3 + polarity, Channels #0-2 - polarity
Channel #3 - HV cable #1
+ bias - core aida04, braid aida12, LK1 ( HV local ground ) fitted aida12, aida03, aida11
bias bonds aida01 and aida09 probably broken
aida03 LK3 ( DSSSD PCB ground ) fitted
AIDA Half rev A adaptor PCBs aida06 & aida08 - not connected to ribbon cable/test/HV
DSSSD #1 - adaptor PCB ribbon cable drain wires connected to respective adaptor PCB ground
DSSSD #2 ( not installed ) adaptor PCB ribbon cable and ribbon cable drain wires floating
AIDA Half rev B adaptor PCBs DSSSD#1 - FEE64 cooling plate - adaptor PCB ground *not* connected
AIDA Half rev A adaptor PCBs aida06 & aida08 - not connected to ribbon cable/test/HV - FEE64 cooling plate - adaptor PCB ground fitted
ground to AIDA support frame *not* connected
test + / test - *not* connected
DSSSD#1 3208-3/-21/-22
bias +120V leakage current +17.13uA - attachments 1-14
per FEE64 1.8.W spectra - 200us FSR - attachments 1-2
per FEE64 1.8.W spectra - 20us FSR - attachments 3-4
bias +100V leakage current +8.35uA - attachments 15-17
per FEE64 1.8.W spectra - 200us FSR
bias +0V leakage current +0uA - attachments 18-20
per FEE64 1.8.W spectra - 200us FSR
14.25 bias +100V leakage current +10.83uA - attachments 21-22
per FEE64 1.8.W spectra - 200us FSR
CAEN channel #3 cable moved from cable tray to floor
14.50 bias +100V leakage current +11.15uA - attachments 23-24
per FEE64 1.8.W spectra - 200us FSR
CAEN N1419ET moved to Weiner NIM bin LHS 19" rack channel #3 cable across floor to AIDA stand
HV cables channels #0-2 disconnected |
|
678
|
Sat Oct 21 02:48:17 2017 |
OH, TD | Saturday 21st October | 10:48 Adapter boards replaced for DSSD 1 &2 (FEEs 1,2,22 and 21)
Previous boards were Rev D new boards are Rev E
System wide checks ok
FEE Temperatures ok - Attachment 1
10:54 DSSDs biased up. Note that after new boards installed DSSD 1 and 2 had leakage currents of around 9uA
during ramp up
Leakage currents appear to have dropped as they reach 100V set point
T = 23.8 H = 45% D.P = +11.1
Leakage and Bias ok - Attachment 2
11:11 Waveforms for FEEs 22, 21, 11 and 13 - Attachments 3 - 10
Statistics - Attachment 11
14:00 System wide checks all ok
Leakage and bias ok - Attachment 12
FEE temperatures ok - Attachment 13
14:26 Spectra comparing the values for nnaida waveforms for different Ibias LF Feedback values
Values are indicated in image title. If not mentioned value 0x8 - Attachments 14 - 23
14:37 Spectra showing the effect of different slow comparator values on the sawtooth signal in the waveforms
Spectra are all nnaida22 and slow comparator values in image titles - Attachments 24 - 26
Attachment FEE Change
14 1 default
15 1 LF 0xf
16 2 default
17 2 LF 0xf
18 2 LF 0xc
19 21 default
20 21 default
21 21 LF 0xf
22 22 default
23 22 LF 0xf
24 22 LF 0xf SC 0xf
25 22 LF 0xf SC 0xd
26 22 LF 0xf SC 0xb
15:09 Raised slow comparator threshold to 0x40 ~ 640keV for all FEEs and all ASICs
Hit pattern in attachment 27
Statistics - Attachment 28
New adapter boards appear to have improved the amount of white noise at default ASIC settings
This is shown with the decrease in statistics and also in the waveforms.
At default settings the saw tooth patterns still appear in the waveforms though attenuated
with lower frequencies and lower amplitudes.
Further improvements can be gained in reducing the amplitude and frequency of the saw tooth
patterns by changing the Ibias LF feedback value though care has to be taken that the pre-amp
signal is not taken to the rails. Hence FEE 2 has a value of 0xc rather than 0xf like the others.
Hit pattern checked for the pulser by raising the slow comparator threshold to 640keV. The boards that
have been changed show a much more believable rate than those that haven't which are still showing
higher than pulser rates.
16:09 The effect of changing the shaping time on the pulser widths was checked.
Optimum still appears to be at around 8us
16:50 DAQ started writing to Oct17/R5 @ 8Mb/s
nnaida 13 SC threshold at 0x20
System wide checks ok
Leakage and bias ok - Attachment 29
FEE Temp ok - Attachment 30
Statistics - Attachment 31 |
|
579
|
Sat May 20 02:39:06 2017 |
CB, OH | Saturday 20 May | 10.35 DAQ continues OK
Current file May2017/R16
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases; leakage currents OK - see attachment 1
FEE64 Temperatures OK - see attachment 2
good events; statistics OK - see attachment 3
No warnings/errors reported by merger since DAQ GO - see attachment 4
*all* system wide checks OK *except* ADC calibration of nnaida7
10.45 E17/F11 ambient temperature +24.8 deg C, RH 39.9%, d.p. +10.0 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 50%)
11.00 DAQ stops OK
Current file May2017/R16
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
11.10 DAQ starts
File May2017/R17
16.30 DAQ continues OK
Current file May2017/R17
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases; leakage currents OK - see attachment 5
FEE64 Temperatures OK - see attachment 6
good events; statistics OK - see attachment 7
No warnings/errors reported by merger since DAQ GO - see attachment 8
*all* system wide checks OK *except* ADC calibration of nnaida7
16.45 E17/F11 ambient temperature +24.3 deg C, RH 39.1%, d.p. +9.5 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 50%)
16.50 DAQ stops OK
Current file May2017/R17
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
16.54 DAQ starts
File May2017/R18
Attached Ras Pi system console log for USB0 |
|
341
|
Mon Aug 22 10:35:06 2016 |
TD | Saturday 20 August | |
|
90
|
Sat May 2 02:04:50 2015 |
JA, TD, AE, CG, VP & JLT | Saturday 2 May 2015 | 0055: Degrader changed. 1mm removed.
1.4mm total
0537: R38 ends nnaida11 slow comparator 0x20 -> 0x40 LEC fast comparator -> 0xff
0530: R39 10.00 AIDA status screenshots
1159: R39 ends HEC fast comparator 0x2 -> 0xf (all FEE64s)
1202: R40 nnaida8 no SYNCS see attachments 19-22
VFEP toggled merge pause state check merge activity spinner accelerates nnaida8 GO Electronics (from select required function menu of Run Control) nnaida8 started OK toggled merge pause state
1500: Attachments 23-28 show waveforms, low E and high E spectra for nnaida6+11.
Increasing fast comp threshold to 0xf shifts position of energy cut off away from zero point, as expected, but does not remove low E peak around ch 32500.
1530: Increase bias to +150V on det 1 (ch 1). Attachments 29-34 show waveforms, low E and high E spectra with increased bias voltage. Diode link threshold at 0x23
V high E events in .L spectra show reduction over those before bias increase.
In .H spectra from both nnaida6+11, increased bias reduced threshold. Finite threshold still seen on n-side however (greater than on p-side).
All references/comparisons in this ELog entry re. nnaida11 are w.r.t. to spectra/waveforms seen at this 'standard' setting.
1544: Changed diode link thresh on nnaida11 to 0x11. Attachments 35-37.
Saved run R42.
High energy spectra saw threshold increase of ~700ch, but no other changed were observed.
1555: Change nnaida11 diode link thresh to 0x29. Saved run R43. Attachments 38-40.
Saw reduction in high E threshold by ~700 ch but no other obvious changes.
1610: Changed diode link thresh on nnaida11 to 0x14 and preAmp reference to 0x20. Saved run R44. Attachments 41-44.
Waveforms look much worse, more flatlining that previously seen.
High E spectra show marginally higher threshold. No significant change in low E spectra.
1630: Changed nnaida11 preAmp ref to 0x40 and diode link thresh to 0x38. Saved run R45. Attachments 45-47
Waveforms look similar to original setting. High E spectra show no significant change.
Low E spectra have small peak near 32k and v. wide stretching to top of FSR.
1643: Changed nnaida11 preAmp ref to 0x60 and diode link thresh to 0x58. Saved run R46. Attachments 48-50.
Waveforms settled on ~7500 much more frequently, with most signals beginning and returning to ~7500.
High E spectra thresh at ~33500 as it was with 'standard' setting.
Low E spectra show vast reduction in high E rubbish, looking more like an exponential decay compared to previous wide 'mound'.
Big improvement over previous settings. Will try all n-side FEE with these settings later.
1700: Changed nnaida11 diode link thresh to 0x5a. Saved run R47 (~2hr run during tea break and other work).
0x60 HEC fast comparator threshold (all FEE64s except nnaida30) 0x02.
19.04 R47 ends Change BigRIPS setting from 110Zr to 88Ge
19.15 R48 Pulser walkthough BNC PB-4 amplitude 90,000-10,000 @ 10,000 step, freq 25Hz.
nnaida7 showed no SYNCS.
Used procedure described above (1202) - nnaida7 recovered OK
19.28 Started run R48 - pulser walkthrough.
R48 ends OK..
1944: Changed fast comparator threshold on LEC for...
- nnaida 1: 0xb -> 0x30
- nnaida2: 0x18 -> 0x30
- nnaida6: 0x10 -> 0x30
- nnaida10: 0x10 -> 0x30
- nnaida13: 0x12 -> 0x30
- nnaida14: 0x14 -> 0x30
Change, for all n-side FEE64s, preAmp reference from previous value to 0x60 and diode link thresh to 0x5a.
Saved settings to /MIDAS/DB/EXPERIMENTS/AIDA/2015Apr30-diode-mod3
(around) 20:30 pm: started data taking for 88Ge setting. First runs are with empty H target at MINOS/DALI for transmission measurement.
Degrader also changed during run R50. Initially: 0.6mm + 0.4mm + (0.3 mm?) + 1mm. The 1mm degrader was removed after ~ 1hr of run.
2300: NNAIDA#11: changed Fast Comparator of Low Energy channels to 0x40. It was set at 0xFF, and no discriminator data being produced. Rate of ~12 kHz for discriminator events in NNAIDA#11 for this setting (comparable to other FEE64s).
RUN: R51_* started after adjusting the NNAIDA11 setting |
|
459
|
Sat Nov 19 02:46:09 2016 |
TD, CG | Saturday 19 November |
11.45 DSSSD bias & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
Updated copy of GoogleDocs leakage current spreadsheet - attachment 4
20:17 DSSD bias and leakage currents ok (attachments 4+5).
FEE temps ok (attachment 6) |
|
652
|
Sat Jun 10 09:24:45 2017 |
AE, TD | Saturday 19 June 16.00-24.00 | 17.25 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachment 4
No warnings/errors reported by merger since DAQ GO - see attachment 5
*all* system wide checks OK (zero fails)
17.30 analysis of file RIBF128/R7_1065 - dead time < 0.5%, no timewarps, 3 MBS timewarps - see attachment 6
17.35 online analysis - ADC & disc data synchronised - see attachment 7
all SortSas spectra & histograms zero'd, waveforms set x-range = 1000ch = 2ms
18.05 BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
BigRIPS 149Xe setting, degrader 2mm Al (at F7), 1.3mm Al fixed + 2mm Al variable (at F11)
18.38 Start DAQ
AIDA file RIBF128/R7_1083
BRIKEN file 111
BigRIPS file 4001
F11 rate ~100Hz, ~50 neutrons/s
18.56 Stop DAQ
AIDA file RIBF128/R7_1088
18.38 Start DAQ
AIDA file RIBF128/R7_1088
BRIKEN file 112
BigRIPS file 4002
19.03 per DSSSD x versus y (HEC) - see attachment 8
per DSSSD E_p versus E_n (HEC) 20MeV/ch nominal - see attachment 9
Rates from offline analysis RIBF128/R7_1089
*** DSSSD # 1 count: 258088 old count: 206122 dt: 1.03 s LEC rate: 50652.59 Hz
*** DSSSD # 2 count: 377054 old count: 301162 dt: 1.03 s LEC rate: 73973.87 Hz
*** DSSSD # 3 count: 113574 old count: 89972 dt: 1.03 s LEC rate: 23005.47 Hz
*** DSSSD # 4 count: 104475 old count: 83626 dt: 1.03 s LEC rate: 20322.05 Hz
*** DSSSD # 5 count: 34511 old count: 27812 dt: 1.03 s LEC rate: 6529.69 Hz
*** DSSSD # 6 count: 78446 old count: 62771 dt: 1.03 s LEC rate: 15278.82 Hz
*** DSSSD # 1 count: 2 old count: 2 dt: 1.03 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 95 old count: 76 dt: 1.03 s HEC rate: 18.52 Hz
*** DSSSD # 3 count: 30 old count: 24 dt: 1.03 s HEC rate: 5.85 Hz
*** DSSSD # 4 count: 12 old count: 8 dt: 1.03 s HEC rate: 3.90 Hz
*** DSSSD # 5 count: 27 old count: 24 dt: 1.03 s HEC rate: 2.92 Hz
*** DSSSD # 6 count: 81 old count: 67 dt: 1.03 s HEC rate: 13.65 Hz
19.21 Detector biases & leakage currents OK - see attachments 10 & 11
FEE64 Temperatures OK - see attachment 12
good events statistics stable & OK - see attachment 13
No warnings/errors reported by merger since DAQ GO - see attachment 14
*all* system wide checks OK (zero fails)
19.30 analysis of file RIBF128/R7_1095 - dead time 1%, no timewarps, 1 MBS timewarps - see attachment 15
20.00 Stop DAQ
AIDA file RIBF128/R7_1104
18.38 Start DAQ
AIDA file RIBF128/R7_1104
BRIKEN file 113
BigRIPS file 4003
BigRIPS slit change and n background check
20.27 Stop DAQ
AIDA file RIBF128/R7_1111
20.28 Start DAQ
AIDA file RIBF128/R7_1111
BRIKEN file 114
BigRIPS file 4004
BigRIPS F1 slits changed
20.28 all SortSas spectra zero'd
21.15 Start DAQ
AIDA file RIBF128/R7_1123
BRIKEN file 115
BigRIPS file 4005
21.32 RF down
22.15 Stop DAQ
AIDA file RIBF128/R7_1138
20.28 Start DAQ
AIDA file RIBF128/R7_1138
BRIKEN file 116
BigRIPS file 4006
22.37 Detector biases & leakage currents OK - see attachments 16 & 17
FEE64 Temperatures OK - see attachment 18
good events statistics stable & OK - see attachment 19
No warnings/errors reported by merger since DAQ GO - see attachment 20
*all* system wide checks OK (zero fails)
22.42 analysis of file RIBF128/R7_1095 - dead time ~1%, no timewarps, 2 MBS timewarps - see attachment 21
22.48 online analysus
per DSSSD x versus y (HEC) - see attachment 22
per DSSSD E_p versus E_n (HEC) 20MeV/ch nominal - see attachment 23
ADC & disc data synchronised - see attachment 24
offline analysis RIBF128/R7_1146 rates
*** DSSSD # 1 count: 389187 old count: 340234 dt: 1.02 s LEC rate: 47972.00 Hz
*** DSSSD # 2 count: 562493 old count: 494318 dt: 1.02 s LEC rate: 66808.79 Hz
*** DSSSD # 3 count: 168279 old count: 147281 dt: 1.02 s LEC rate: 20577.21 Hz
*** DSSSD # 4 count: 156439 old count: 136327 dt: 1.02 s LEC rate: 19708.96 Hz
*** DSSSD # 5 count: 52041 old count: 45539 dt: 1.02 s LEC rate: 6371.70 Hz
*** DSSSD # 6 count: 121463 old count: 106320 dt: 1.02 s LEC rate: 14839.54 Hz
*** DSSSD # 1 count: 1 old count: 1 dt: 1.02 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 66 old count: 57 dt: 1.02 s HEC rate: 8.82 Hz
*** DSSSD # 3 count: 41 old count: 35 dt: 1.02 s HEC rate: 5.88 Hz
*** DSSSD # 4 count: 1 old count: 1 dt: 1.02 s HEC rate: 0.00 Hz
*** DSSSD # 5 count: 11 old count: 11 dt: 1.02 s HEC rate: 0.00 Hz
*** DSSSD # 6 count: 82 old count: 66 dt: 1.02 s HEC rate: 15.68 Hz
23.15 Stop DAQ
AIDA file RIBF128/R7_1153
23.15 Start DAQ
AIDA file RIBF128/R7_1153
BRIKEN file 117
BigRIPS file 4007
23.38 beam lost - RF restart
AIDA file RIBF128/R7_1158 |
|
703
|
Sat Nov 18 04:25:16 2017 |
CB, TD | Saturday 18 November |
13.27 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
7x FEE64s <10k
4x FEE64s 10-20k
6x FEE64s 20-30k
4x FEE64s 30-40k
2x FEE64s 40-50k
1x FEE64 >50k (nnaida13 64k)
*all* system wide checks OK *except* nnaida7 fails ADC calibration
13.50 all spectra zero'd
*all* ASIC slow comparator settings -> 0xa
DAQ statistics - see attachment 5
17:05 1.*.W spectra for front strips attached - see attach 6-17
Layout 3 & 4 - see attach 18,19
nnaida1 Peak width = 79.68+/- 0.3080, Peak area = 189026.00+/- 434.77
nnaida2 Peak width = 126.52+/- 1.0035, Peak area = 180119.00+/- 426.09
nnaida5 Peak width = 79.16+/- 1.1547, Peak area = 189192.00+/- 434.96
nnaida6 Peak width = 78.30+/- 0.2948, Peak area = 189316.00+/- 435.10
nnaida9 Peak width = 77.54+/- 0.2578, Peak area = 189201.00+/- 434.97
nnaida10 Peak width = 88.96+/- 0.7201, Peak area = 189252.00+/- 435.03
nnaida13 Peak width = 225.44+/- 0.6773, Peak area = 178047.00+/- 421.96
nnaida14 Peak width = 81.43+/- 0.5754, Peak area = 188275.50+/- 435.05
nnaida17 Peak width = 74.42+/- 0.3670, Peak area = 189139.00+/- 434.90
nnaida18 Peak width = 78.13+/- 2.1601, Peak area = 188683.00+/- 436.03
nnaida21 Peak width = 155.44+/- 0.7619, Peak area = 183728.00+/- 428.64
nnaida22 Peak width = 120.95+/- 0.3604, Peak area = 184462.00+/- 429.49
nnaida3 Peak width = 80.08+/- 0.1346, Peak area = 190083.00+/- 435.99
nnaida4 Peak width = 82.15+/- 0.1403, Peak area = 190143.00+/- 436.0
nnaida7 Peak width = 87.46+/- 0.6821, Peak area = 190314.00+/- 436.25
nnaida8 Peak width = 69.86+/- 1.0958, Peak area = 189915.50+/- 437.33
nnaida11 Peak width = 99.95+/- 0.2553, Peak area = 188884.00+/- 436.10
nnaida12 Peak width = 101.40+/- 0.2937, Peak area = 188737.00+/- 436.02
nnaida15 Peak width = 78.17+/- 1.8691, Peak area = 188912.00+/- 436.61
nnaida16 Peak width = 107.16+/- 1.1332, Peak area = 190392.00+/- 436.34
nnaida19 Peak width = 137.14+/- 0.2579, Peak area = 186414.50+/- 432.426
nnaida20 Peak width = 128.06+/- 0.9060, Peak area = 185287.00+/- 437.16
nnaida23 Peak width = 103.67+/- 0.3636, Peak area = 190221.00+/- 436.14
nnaida24 Peak width = 99.72+/- 0.4577, Peak area = 189176.00+/- 436.85 |
|
924
|
Sat Nov 18 02:28:26 2023 |
TD, NH, JB | Saturday 18 November | 03.20 c. 3k per spill 13N beam to S4
Observe scatter of events at all energies for LEC
Switch LE -> MEC
aida02 & aida04 slow comparator 0xf -> 0x3 ( c.1.5MeV )
All other ( p+n ) FEE64s slow comparator 0xa ( c. 5MeV )
For c. 700MeV/u 14N + 6cm s.steel -> c. 350MeV/u 14N -> c. 30MeV energy loss in 1mm Silicon, c. 45MeV energy loss in 3mm plastic
per n+n FEE64 1.8L spectra - attachment 1
observe 3x peaks above threshold - different Z fragments?
per FEE64 Stat spectra
04.10 DSSSD bias -150V leakage current -5.380uA - attachment 3
FEE64 temps OK - attachment 4
ADC data item stats - attachment 5
per FEE64 Stat spectra - attachment 6
per FEE64 1.8.L spectra - attachments 7-8
per FEE64 1.8.W spectra - 20us FSR - attachments 9-10
05.03 aida02 & aida04 slow comparators 0x3 -> 0xa
All spectra zero'd
c. 06.30 Beam tests end
DAQ stopped. DSSSD HV OFF. AIDA power OFF.
|
|
804
|
Sat May 18 04:47:22 2019 |
TD | Saturday 18 May | 12.47 DAQ continues OK to file May19/R7_3
alpha background
ASIC settings 2018Oct03-13.26.58
*except* slow comparator 0xa -> 0x64
BNC PB-4 Pulser OFF
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachments 4
Merger OK - see attachment 5
TapeServer OK - see attachment 6
12.51 Check ASIC Control *all* ASICs & FEE64s
1.8.L spectra - see attachments 7 & 8
p+n FEE64s 1.8.W spectra 20us, 200us, 2ms, 20ms FSR - attachments 9-12
n+n FEE64s 1.8.W spectra 20us, 200us, 2ms, 20ms FSR - attachments 13-16
13.13 analysis of May19/R7_3 - see attachment 17
deadtime OK
ADC data for FEE64s nnaida5 & nnaida6 hot channels (Stat spectrum channel # 104)
Also observed at a much lower rate for nnaida1 & nnaida2
13.27 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C - water topped up to H level marker
Temperature +24.6 deg C dew point +7.1 deg C RH 32.6% |
|
665
|
Sat Jun 17 05:47:58 2017 |
TD | Saturday 17 June | 13.47 DAQ continues
AIDA file RIBF148/R10_39
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0x64
LEC/MEC fast comparator 0x14
13.49 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachment 4
No warnings/errors reported by merger since start of RIBF148/R10 - see attachment 5
No changes to PLL and DCM clock Lock monitor - see attachment 6
*all* system wide checks OK (zero fails)
14.00 analysis file RIBF148/R8_39 - zero deadtime, zero MBS and zero ts timewarps - see attachment 7
14.03 online analysis
ADC & disc data synchronised - see attachment 8
per DSSSD m_p versus m_n (LEC) - see attachments 9
per DSSSD x versus y (LEC) - see attachment 10
per DSSSD E_p versus E_n (LEC) - 512x512 spectra - nominal 20keV per channel - see attachment 11
per DSSSD side ADC ts - event ts - see attachment 12
14.17 Layout per FEE64 Rate, HitRate and 1.8.* spectra - see attachments 13-18
nnaida11 & nnaida13 1.*.W spectra - see attachments 19-20
3kHz modulated HF noise positive input FEE64s
BRIKEN and Clovers on
14.32 Ambient temperature +24.3 deg C, d.p. +8.7 deg C, RH 37.5%
Julabo FL11006 set point +20.0 deg C actual +20.0 deg C - water level c. 75%
14.34 DAQ stop
AIDA file RIBF148/R10_40
14.45 nnaida13 1*W spectra
Ibias LF feedback attachment
0x8 (default) 21
0x0 22 & 23
0xf 24
0x0 preamp o/p -> V rail
0x8 - 0xf no obvious difference
14.52 slow comparator 0x64 -> 0xa
Ibias LF feedback attachment
0x8 (default) 25 27
0xf 26 28
0xf appears to reduce (but not eliminate) frequency and amplitude of saw tooth transients
no obvious effect on good event rate
for nnaida13 combination of Ibias LF feedback 0x8 -> 0xf and slow comparator 0xa -> 0xf
largely eliminates saw tooth except for noisiest strips e.g. 1.1.W 'edge' strip
good events 280k -> 61k
17.12 DAQ start
AIDA file RIBF148/R11
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0xf
LEC/MEC fast comparator 0x14
Ibias LF feedback 0x8 -> 0xf
Layout Rate, HitRate and 1.8.* spectra -see attachments 29-35
Merged data rate c. 500k data items/s, 4Mb/s
17.50 DAQ stop
AIDA file RIBF148/R11_4
17.54 DAQ start
AIDA file RIBF148/R12
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0xf -> 0xa
LEC/MEC fast comparator 0x14
Ibias LF feedback 0xf
good events statistics - see attachment 36
18.14 DAQ stop
AIDA file RIBF148/R12_6
DSSSD bias cycled 100->0->100V
18.21 DAQ start
AIDA file RIBF148/R13
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0xa
LEC/MEC fast comparator 0x14
Ibias LF feedback 0xf -> 0x8
good events statistics - see attachment 37
18.40 DAQ stop
AIDA file RIBF148/R13_5
18.42 Detector biases & leakage currents OK - see attachments 38 & 39
18.59 analysis file RIBF148/R13_5 -c. 1% deadtime, zero MBS and zero ts timewarps - see attachment 40 |
|
387
|
Sat Oct 15 03:27:31 2016 |
TD | Saturday 15 October | 11.27 DAQ found stopped
Most recent file R42_164, last accessed 07.18
Restart merger OK
DAQ STOP OK
System-wide checks - see attachments 1-5
ASIC clock timestamp, SYNC errors fail *but* SYNC pulses OK
ReSYNC OK
System-wide checks OK
DSSSD bias & leakage currents OK - see attachments 6 & 7
FEE64 temperatures OK - see attachment 8
R42_164 ADC data synchronised
aidas1> ./analyser2 /TapeData/Sept2016/R42_164
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 2444
ADC data format: 19809141 ( 1404089.4 Hz)
Other data format: 131455 ( 9317.6 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 7 ( 0.5 Hz)
RESUME: 7 ( 0.5 Hz)
SYNC100: 129011 ( 9144.4 Hz)
FEE64 disc: 2010 ( 142.5 Hz)
MBS info: 420 ( 29.8 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 21 ( 1.5 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 14.108 s
FEE module #: 1 elapsed dead time 0.000 s
FEE module #: 2 elapsed dead time 0.000 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.334 s
FEE module #: 6 elapsed dead time 0.042 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.000 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.000 s
FEE module #: 12 elapsed dead time 0.000 s
FEE module #: 13 elapsed dead time 0.000 s
FEE module #: 14 elapsed dead time 0.000 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.005 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.000 s
FEE module #: 21 elapsed dead time 0.000 s
FEE module #: 22 elapsed dead time 0.000 s
FEE module #: 23 elapsed dead time 0.000 s
FEE module #: 24 elapsed dead time 0.000 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 0.586s ( 4171.093 blocks/s, 260.693 Mb/s)
11.39 DAQ starts (R43)
12.07 Disk housekeeping caused TapeServer problem
DAQ stopped OK after some minutes and restarting merger
12.43 DAQ starts (R46)
18.26 DAQ stalled
Latest file R46_109 (most recent access 18.26)
Merger error messages - see attachment 9
Restart merger - error messages - see attachment 10
Analysis of R46_109
ADC data synchronised
aidas1> ./analyser2 /TapeData/Sept2016/R46_109
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 4688
ADC data format: 37985730 ( 1342216.8 Hz)
Other data format: 263662 ( 9316.4 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 25 ( 0.9 Hz)
RESUME: 25 ( 0.9 Hz)
SYNC100: 258788 ( 9144.2 Hz)
FEE64 disc: 3981 ( 140.7 Hz)
MBS info: 843 ( 29.8 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 41 ( 1.4 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 28.301 s
FEE module #: 1 elapsed dead time 0.000 s
FEE module #: 2 elapsed dead time 0.013 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.298 s
FEE module #: 6 elapsed dead time 0.200 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.001 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.000 s
FEE module #: 12 elapsed dead time 0.000 s
FEE module #: 13 elapsed dead time 0.000 s
FEE module #: 14 elapsed dead time 0.003 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.086 s
FEE module #: 18 elapsed dead time 0.054 s
FEE module #: 19 elapsed dead time 0.097 s
FEE module #: 20 elapsed dead time 0.000 s
FEE module #: 21 elapsed dead time 0.000 s
FEE module #: 22 elapsed dead time 0.001 s
FEE module #: 23 elapsed dead time 0.000 s
FEE module #: 24 elapsed dead time 0.000 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 2.102s ( 2230.721 blocks/s, 139.420 Mb/s)
11.00 Sunday 16 October
DAQ STOP requested - nnaida1-24 all stop *except* nnaida6 which remains going - Run Control displays RESET
only
DAQ RESET
System-wide checks all OK
Normal setup and DAQ restart (see https://elog.ph.ed.ac.uk/AIDA/388 )
DAQ SETUP
|
|
842
|
Sat Jun 15 01:05:41 2019 |
CA, CB, TD, CG, OH, DK, ML | Saturday 15 June | 09.05 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C
Water level c. 75% M-H markers
Temperature +24.1 deg C dew point +8.3 deg C RH 36.2%
DAQ continues OK
ASIC settings 2019Jun13-08.56.35
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics - OK - see attachment 4
11x <20k 23x < 50k 24x <100k cf. 9x <20k 23x < 50k 24x <100k 22.39 yesterday
Merger OK - see attachment 5
TapeServer OK - see attachment 6
p+n FEE64s 1.8.W spectra 20us FSR - attachment 7
n+n FEE64s 1.8.W spectra 20us FSR - attachment 8
1.8.L spectra - see attachments 9 & 10
nnaida1 74 ch FWHM, nnaida3 78 ch FWHM - cf. 81 & 77 ch FWHM respectively 23.20 yesterday
FEE64 Rate spectra - attachment 11
Check ASIC Control *all* FEE64s & ASICs x2
Check ASIC Control x2
FEE64 ASIC
10 4
16 4
17 4
FEE64 Rate spectra - attachment 12 - some channels recovered
09.19 ADC data synchronised - attachment 13
09.23 zero all histograms
zero DAQ stats
16:45 DAQ Continues to run
Rates on 17, 20, 22 amd 23 are up - attachment 14
Bias and leakage current ok - attachment 15
System wide checks ok
ASIC check ok
16:58 Statistics back to normal level - attachment 16
17.34 DAQ stop
replaced kapton pcb on FEE no. 22
DAQ start -> writing to May19/R36
system wide checks ok, *except* naida7 fails adc calibration
good event statistics ok - attachment 17
TapeService and Merger ok - writing at 4 Mb/s - attachments 18 & 19
17.41 zeroed all histograms
c. 19.30 First beam to AIDA + DTAS - see attachments 20-24
*no* degraders
Observe most ions stop in DSSSD#2 with a few stopping in DSSSD#3
focus looks OK but distribution is to LHS as you look upstream to BigRIPS
19.50 Removed upstream PPAC and adjusted ZDS transverse settings to centre - attachments 25-29
Now observe ions now stop mostly in DSSSD#3 but significant fractions still stop ion DSSSD#2
DSSSD#3 appears well focussed and centred
20.19 all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachment 30
FEE64 temperatures OK - see attachment 31
good event statistics - OK - see attachment 32
20.53 xy hit patters in all DSSDs
ions mostly in DSSD3, some still depositing in DSSD2
21.06 attachment 33 - beam slightly focused to the left - xy hit pattern
attachment 34 - beam further focused - xy hit pattern
21.14 DAQ stop
DAQ start writing to /RIBF147/R1
Sync pulse sent by DTAS on file R1_0
21.17 DAQ stop/start
writing to file /RIBF147/R2
sync pulse sent by DTAS - file R2_0
ASIC settings 2019Jun13-08.56.35
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
no degrader
21.24 AIDA file on R2_1
DTAS start 003
BigRIPS run: 2003
21.31 histograms zeroed
good event statistics ok - attachment 35
21.34 AIDA file on R2_2
DTAS start 004
BigRIPS run: 2004
22.02 good event statistics ok - attachment 36
22.16 AIDA file on R2_8
DTAS run 004
BigRIPS run 2004
checked with DTAS
22.29 energy x vs y (HEC) - attachment 37 - grouping ~ 3MeV in all detectors
xy hit pattern (HEC) - attachment 38
implants centered on DSSD3
22.32 AIDA file R2_9
DTAS run 005
BigRIPS run 2005
beam returns
22.34 HEC multiplicity - most events ~1,2,3 pixels - attachment 39
22.35 checked with DTAS
AIDA file R2_10
DTAS run 006
BigRIPS run 2006
22.38 LEC energy x vs y - clear Ex=Ey locus - attachment 40
xy hit pattern LEC - attachment 41
xy multiplicity LEC - attachment 42 - most events 1,2 pixels
22.49 analyzer.f output for file R2_5 - attachment 44
dead time 0.5% in fee19, zero in all others
22.56 problem with beam, beam stopped on AIDA file R2_8
23.05 all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachment 45
FEE64 temperatures OK - see attachment 46
good event statistics - OK - see attachment 47
23.50 AIDA file R2_21
DTAS run 006
BigRIPS run 2006
|
|
564
|
Sat May 13 02:35:53 2017 |
TD, OH | Saturday 13 May | 10.35 DAQ continues OK
Current file May2017/R6_246
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x20
LEC/MEC fast comparator 0xff
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
'good events' statistics OK - see attachment 4
No warnings/errors reported by merger since DAQ GO - see attachment 5
*all* system wide checks OK
10.46 Rate/HitRate spectra - see attachments 6 & 7
1.8.L ADC spectra - see attachments 8 & 9
1.8.W waveforms - see attachments 10-13
10.51 Analysis of data file R6_245 - see attachment 14
Zero AIDA pause/resume
Zero idle-time
AIDA SYNC100 variations ~33/503400
12.03 E17/F11 ambient temperature +24.6 deg C, RH 39.4%, d.p. +9.9 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 65%)
12.04 DAQ stops OK
Current file May2017/R6_250
Files May2017/R6* *deleted*
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
12.15 DAQ starts
File May2017/R7
14.30 Analysis of May2017/R7_29
ADC data synchronised - see attachments 15 & 16
14.37 Analysis of data file R7_29 - see attachment 17
AIDA pause/resume for some FEE64s
dead-time/idle-time <0.5%
AIDA SYNC100 variations ~300/100000 |
|
453
|
Sat Nov 12 01:45:00 2016 |
TD | Saturday 12 November | 10.45 DSSSD bias & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
14.45 DSSSD bias & leakage currents OK - see attachments 4 & 5
15.10 Download .xlsx file of AIDA leakage currents etc from
https://docs.google.com/spreadsheets/d/12hgbrywB10hGsKt5uc2HnLfZymh8_uvM6cEASbbqnBE/edit#gid=1357176413
- see attachment 6 |
|
794
|
Sat May 11 02:50:14 2019 |
CA, OH, TD | Saturday 11th May 2019 | 10:52 system wide checks ok, except naida07 fails ADC calibration
good event statistics, rates in naida19,20,23,24 high (attachment 1)
FEE temperatures ok (attachment 2)
detector bias/leakage currents stable (attachment 3) |
|
305
|
Fri Jun 10 21:07:52 2016 |
AE, DK, TD, ML, MA | Saturday 11 June 2016 | 04.51 Start run AIDA18. Beam is back from the operators.
Scalers are shown as attachment 1
Leak currents seem okay (all < 5 uA), shown as attachments 2 and 3.
Discrim levels have a bit of fluctuation depending on the module -- attachment 4
nnaida24 has some pauses (attachment 5)
09.35 AIDA20* - AIDA24* test runs with no beam, i.e. noise, betas and low rate pulser
to investigate FEE64 synchronisation
AIDA20* nnaida19 data link to Merge program enabled
AIDA21* - nnaida19 removed from DAQ configuration file (startup.tcl) and server/web browser restarted
12.35 Detector bias & leakage current, FEE temperatures - OK - see attachments 5-7 |
|
772
|
Sat Nov 10 03:50:00 2018 |
CA, CB, TD, OH | Saturday 10 November |
12.35 DAQ continues OK - data transfer disabled
12.37 all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
Julabo FL11006 chiller set point +20 deg C actual +20 deg C, water level topped up c. 1 litre - 80% (L-H)
ambient tempature + 27.3 deg C, RH 33.0%, d.p. +9.6 deg C
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachment 4
per FEE64 rate spectra - see attachment 5
1.8.L spectra - see attachments 6 & 7
nnaida1 pulser peak width 71 ch FWHM
1.8.W spectra 20us FSR - see attachments 8 & 9 |
|
650
|
Fri Jun 9 16:22:54 2017 |
PV | Saturday 10 June 00:00-08:00 | 00:21 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_826
00:23 BRIKEN starts run 101
BigRIPS starts run 3107
AIDA on file R7_827
00:26 Offline Analysis of file RIBF128/R7_826- zero timewarps, zero MBS timewarps - see attachment 1
High Energy hit pattern spectra - see attachment 2
AIDA on file R7_828
zeroed Midas sort online spectra
00:36 *All* system wide checks OK
FEE64 Temperatures OK - see attachment 3
Good events statistics OK - see attachment 4
Merger and tape server running - see attachment 5, 6
Detector biases and leakage currents OK - see attachment 7
01:22 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_841
01:24 BRIKEN starts run 102
BigRIPS starts run 3108
AIDA on file R7_841
02:22 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_855
02:23 BRIKEN starts run 103
BigRIPS starts run 3109
AIDA on file R7_856
02:25 Offline Analysis of file RIBF128/R7_855- zero timewarps, 2 MBS timewarps - see attachment 8
High Energy hit pattern spectra - see attachment 9
AIDA on file R7_856
zeroed Midas sort online spectra
02:30 *All* system wide checks OK
FEE64 Temperatures OK - see attachment 10
Good events statistics OK - see attachment 11
Merger and tape server running - see attachment 12, 13
Detector biases and leakage currents OK - see attachment 14
03:24 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_870
03:26 BRIKEN starts run 104
BigRIPS starts run 3110
AIDA on file R7_871
03:42 fRC RF is down, beam is off
03:46 beam is back
04:18 beam is off, fRC RF is down
04:21 beam is back
04:31 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_886
04:32 BRIKEN starts run 105
BigRIPS starts run 3111
AIDA on file R7_887
04:35 Offline Analysis of file RIBF128/R7_886- zero timewarps, 1 MBS timewarps - see attachment 15
High Energy hit pattern spectra - see attachment 16
AIDA on file R7_887
zeroed Midas sort online spectra
04:39 *All* system wide checks OK
FEE64 Temperatures OK - see attachment 17
Good events statistics OK - see attachment 18
Merger and tape server running - see attachment 19, 20
Detector biases and leakage currents OK - see attachment 21
05:31 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_901
05:32 BRIKEN starts run 106
BigRIPS starts run 3112
AIDA on file R7_901
06:30 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_916
06:31 BRIKEN starts run 107
BigRIPS starts run 3113
AIDA on file R7_916
06:35 Offline Analysis of file RIBF128/R7_915- zero timewarps, 2 MBS timewarps - see attachment 22
High Energy hit pattern spectra - see attachment 23
AIDA on file R7_917
zeroed Midas sort online spectra
06:37 *All* system wide checks OK
FEE64 Temperatures OK - see attachment 24
Good events statistics OK - see attachment 25
Merger and tape server running - see attachment 26,27
Detector biases and leakage currents OK - see attachment 28
06:46 RRC power is down, it may take more than 1 hour to fix the problem
AIDA on file R7_920
06:48 BigRIPS and BRIKEN stop their DAQ
AIDA run file R7_920
06:52 BRIKEN starts run 108 (background run without beam)
AIDA on file R7_921 |
|