 Fri May 27 06:38:27 2016, TD, AE & CG, Friday 27 May 2016 13x
|
14.30 DSSSD stack moved upstream to position DSSSD#3 at centre of EURICA.
Initial tests of detector bias with DSSSD #1-6 were Ok. Unfortunately we were unable to bias
DSSSD #7 obtaining either open or short circuit depending on which of the two p+n junction
side and n+n ohmic side detector bias bus lines we connected to.
Demonstrated that short circuit was upstream, of AIDA adaptor PCB by disconnecting Kapton
LH couplers.
Remove DSSSD stack and replace DSSSD #7. In progress.
15.50 Startup AIDA with DSSSDs disconnected
Temperatures & firmware version - see attachment 1
AIDA SYNCs - attachment 2
System wide checks - attachments 3-6 - note persistent nnaida19 ASIC clock and SYNC errors
Statistics nnaida19, 20 - attachments 7-8
nnaida19, 20, 27 & 28 hit pattern and waveform spectra - see attachments 9-13
Some nnaida19 system wide errors above and noisy ASIC#4 hit channel for nnaida28 - otherwise OK |
|
Fri Oct 26 03:28:10 2018, OH, CA, Friday 26 October
|
October 25th:
In anticipation of losing access in the evening on arrival at RIKEN the following was done:
- Chiller was refilled
- All power cables reconnected after being removed in October for the RIKEN power down
- All NIM bins, fan trays and RPis were turned on
- 50MHz AIDA clock was set up and connected
- Remote connections to AC Mains relay and RPi for CAEN bias was tested
- Chiller was powered up
October 26th:
11:31 Still have access to the F11 area due to a bigRIPS delay.
Double checked wiring from yesterday and all still seems good
Chiller is still running with set point at +20 deg C
11:36 FEEs powered up. All 24 mounted
11:57 Bias and leakage currents all ok - attachment 1
FEE temperatures all ok - attachment 2
System wide checks all ok
13:26 Bias and leakage currents ok - attachment 3
FEE temperatures all ok - attachment 4
System wide checks all ok
14:00 Stats are ok - attachment 5
Appear similar to last time: https://elog.ph.ed.ac.uk/AIDA/747
However FEE24 and 24 appear much noisier than last time with rates around 100k
19:24 Pulser walkthrough run from 90000 to 10000 in steps of 10000 for R2
Opened file Oct18/R3, alpha run, threshold at 100kev, pulser on.
|
|
Fri May 26 02:20:42 2017, CB, OH, NN, Friday 26 May 15x
|
10.20 DAQ continues OK
Current file May2017/R27_22
Detector biases; leakage currents OK - see attachment 1
FEE64 Temperatures OK - see attachment 2
good events; statistics OK - see attachment 3
No warnings/errors reported by merger since DAQ GO - see attachment 4
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
10.30 E17/F11 ambient temperature +24.2 deg C, RH 39.7%, d.p. +9.7 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 75%)
Left DAQ running on alpha background calibration run
ttyUSB7 log (nnaida1) attached
GUI got stuck while attempting to drag-and-drop ttyUSB7 to ELOG to upload. Terminal still working and
confirmed Merger working OK.
Killed nautilus process to get GUI unstuck. Uploaded ttyUS7 via Browse -> Upload button on ELOG instead.
15.51 DAQ continues OK
Current file May2017/R27_28
Detector biases; leakage currents OK - see attachment 6
FEE64 Temperatures OK - see attachment 7
good events; statistics OK - see attachment 8
No warnings/errors reported by merger since DAQ GO - see attachment 9
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
15.53 E17/F11 ambient temperature +24.1 deg C, RH 40.1%, d.p. +9.8 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 75%)
Left DAQ running on alpha background calibration run
ttyUSB7 log (nnaida1) attached
19.20 DAQ continues OK
Current file May2017/R27_31
Detector biases; leakage currents OK - see attachment 11 & 12
FEE64 Temperatures OK - see attachment 13
good events; statistics OK - see attachment 14
No warnings/errors reported by merger since DAQ GO - see attachment 15
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (status=6)
19.30 E17/F11 ambient temperature +24.2 deg C, RH 38.5%, d.p. +9.2 deg C |
|
Fri Aug 26 02:10:31 2016, TD, Friday 26 August 28x
|
10.11 R9 continues
ASIC settings 2016Aug20-15.34.53
Discriminator masks -> 0x0
From Correlation Status & Control tab change Trigger delay from 0x180 to 0x5
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
t_r 50ns tau_d 50us
- polarity
INT ref, delay MIN, tail pulse
External (random) trigger from EG&G Ortec 462 Start output (Range 81.92us) - frequency c. 120Hz
B2F/F11 temp +24.8 deg C, d.p. +12.9 deg C, RH 46.8%
DSSSD bias/leakage current OK - see attachments 1-2
FEE64 temperatures OK - see attachment 3
Some error messages observed for merger - see attachment 4-12
All related to Q5 (nnaida6)
System-wide checks OK - see attachments 13-18
AIDA SYNC, PAUSE, RESUME, Correlation L, SYNC time warp, Good Events, nnaida6, nnaida5 & nnaida20
statistics - see attachments
19-28
Analysis of R9_561 shows data synchronised - see attachmen
FEE # versus timestamp (0.1ms / channel)
Note nnaida19 not currently configured
10.49 R9 stops |
|
Fri Nov 25 07:33:44 2016, TD, Friday 25 November 9x
|
16.35 DSSSD bias & leakage currents OK - see attachments 1 & 2
note - the significant increase observed yesterday appears to be plateau'ing
FEE64 temperatures OK - see attachment 3
17.10 Rate, HitRate, 1.8.L & 1.8.W spectra - see attachments 4-9 |
|
Fri Nov 24 10:36:06 2023, NH, Friday 24 November
|
Pulser LEMOs removed from p+n fees
Pulser connected to n+n fees: aida02 and aida04
BNC PB-5 Polarity --> NEGATIVE
HV and FEE power up
Rates look similar to usual (Attachments 1 and 2)
Turn on pulser, see them in n+n spectra as expected (attachment 3)
Pulser run R6
See peaks in ADC spectra (attachment 4)
Remove pulser from aida02, left on aida04 with 50Ohm terminator
AIDA powered off, HV off |
|
Fri May 24 03:04:26 2019, TD, Friday 24 May 15x
|
11.04 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C
Water level c. 75% M-H markers
Temperature +26.1 deg C dew point +4.2 deg C RH 24.4%
DAQ continues OK to file May19/R9_5
alpha background
ASIC settings 2019May19-17.54.03
slow comparator 0x64
BNC PB-4 Pulser OFF
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachments 4
Merger OK - see attachment 5
TapeServer OK - see attachment 6
1.8.L spectra - see attachments 7 & 8
p+n FEE64s 1.8.W spectra 20us FSR - attachment 9
n+n FEE64s 1.8.W spectra 20us FSR - attachment 10
14.17 analysis of May19/R9_5 - see attachment 11
deadtime OK *except* nnaida22
ADC data for FEE64s nnaida5 & nnaida6 hot channels (Stat spectrum channel # 104)
Also observed at a much lower rate for nnaida1 & nnaida2
Statistics imply nnaida22 running at high rate for some part of R9_5
analysis of May19/R9_4 - see attachment 12
No indication of higher rates for nnaida22
11.19 Check ASIC Control *all* ASICs & FEE64s
11.29 zero DAQ statistics
14.42 DAQ stop file May19/R9_6
Run stopped to move AIDA out of DTAS prior to changes to Pb shielding upstream of (CH2)n shield
15.01 AIDA removed from inside DTAS
Slow comparator 0x64 -> 0xa
Check ASIC Control *all* ASICs & FEE64s
good event statistics OK - see attachments 13
13x < 20k, 22 < 50k, 0 > 100k
p+n FEE64s 1.8.W spectra 20us FSR - attachment 14
n+n FEE64s 1.8.W spectra 20us FSR - attachment 15
all system wide checks OK *except* nnaida7 fails ADC calibration
zero all histograms
Slow comparator 0xa -> 0x64
Check ASIC Control *all* ASICs & FEE64s
15.08 DAQ start file May19/R10
nnaida1 'good event' rate changed from c. 380Hz to 0Hz at Start ASIC Readout - DAQ stopped
15.10 DAQ start file May19/R11
alpha background
ASIC settings 2019May19-17.54.03
slow comparator 0x64
BNC PB-4 Pulser OFF |
|
Fri Jun 22 02:50:37 2018, OH, TD, Friday 22 June 2018
|
10:50 Yesterday 4 FEE modules installed for FEE64s 25-32
dhcpd.conf updated to reflect MAC addresses of new FEE64s
AIDA config file updated
located at /MIDAS/config/TclHttpd/aidas1/
Firmware updated to /MIDAS/Aida/FEE_GF_Nov16_3.bin
Using run control GUI failed for nnaida28 - see attachment 1
Re-run manually OK
FEE64 temperatures OK, all firmware versions OK - see attachment 2
Power cycle all FEE64 mounted. 5 minute delay in nnaida30 being mounted
Updated ASIC, DISC (but not WAVEFORM) settings for FEE64s 25-32
DB key 2018Jun22-11.28.18
Update Options for FEE64s 25-32 (now same as FEE64s 1-24)
Power cycle OK
Histogramming tag (H) drops for FEE64s 25-32 at DAQ GO - see attachment 3
*all* FEE64 statistics (except histogram-related counters) OK
AIDA config & dhcpd.conf files attached - see attachments 4-5 |
|
Fri Oct 21 01:41:54 2016, TD, Friday 21 October 14x
|
09.38 DAQ (R66) continues OK
Detector bias and leakage currents OK - see attachments 1&2
FEE64 temperatures OK - see attachment 3
System wide checks SYNC count & SYNC errors fail - see attachments 4-7 - other checks OK
R66_367 ADC data synchronised
AIDA SYNC stats - attachment 8
Some merger errors - see attachment 9
13.53 DAQ found stalled
Most recent files R66_396 last accessed 10.55
System wide checks SYNC count & SYNC errors fail - see attachments 10-13 - other checks OK
AIDA SYNC stats - attachment 14
No further merger error messages
Restart merger OK
DAQ STOP OK
DAQ RESET & SETUP OK
ReSYNC OK
System-wide checks OK
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
14.02 DAQ starts (R67)
18.27 DAQ found stalled
Most recent file R67_121 last accessed 18.26
Restart merger
DAQ STOP
System wide checks
DAQ RESET & SETUP
System-wide checks
18.39 DAQ start (R68)
Disable H & data transfer #1
Restart merger & tapeserver
Enable H & data transfer #1
18.44 DAQ stalled
Most recent file R68_1 last accessed 18.44
Restart merger
DAQ STOP
System wide checks
DAQ RESET & SETUP
System-wide checks
18.53 DAQ starts (R70) |
|
Fri Jun 21 01:08:35 2019, CA, CB, Friday 21 June
|
09.08 all system wide checks okay *except* naida7 fails adc calibration
mismatch between sync pulses received from master and FEE64 - attachment 1
FEE64 temperatures ok - attachment 2
detector bias/leakage currents ok - attachment 3
leakage currents slightly ramping since last night
RH 50.7%, Temperature 22.2 deg, dew point 11.6 deg
09.30 AIDA powered off and now in safe state |
|
Fri Oct 20 01:43:40 2017, OH, Friday 20th October 6x
|
09:43 DAQ continues ok
System wide checks all ok
Detector bias and leakage ok - Attachment 1
FEE temperatures ok - Attachment 2
On file R3_279 writing at ~11Mb/s
10:07 Waveforms for nnaida 13, 11, 20 and 22 - Attachments 3-7
nnaida 13 & 22 p-side
nnaida 11 & 20 n-side
Preamp feedback settings for ASIC are still default
10:49 DAQ Stopped
Detector bias taken off |
|
Fri Sep 2 06:22:26 2016, TD, Friday 2 September 17x
|
14.20 R11 continues
DSSSD bias/leakage current OK - see attachments 1-2
FEE64 temperatures OK - see attachment 3
System-wide checks OK *except* nnaida19 fails ASIC timestamp check (no change)
Free memory - see attachment 4
Merger errors messages for links 4 & 5 - see attachment 5
AIDA SYNC, PAUSE, RESUME, Correlation L, SYNC time warp, Good Events, AIDA disc, nnaida6, nnaida5 &
nnaida20 statistics - see
attachments 6-16
Analysis of R11_645 - FEE64 data synchronised - see attachment 17
aidas1> ./analyser2 /TapeData/Aug2016/R11_645
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 156678476 ( 1098367.0 Hz)
Other data format: 104409524 ( 731944.6 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 92 ( 0.6 Hz)
RESUME: 92 ( 0.6 Hz)
SYNC100: 1303563 ( 9138.4 Hz)
FEE64 disc: 103104691 ( 722797.4 Hz)
MBS info: 1086 ( 7.6 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 650 ( 4.6 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 142.647 s
FEE module #: 1 elapsed dead time 0.186 s
FEE module #: 2 elapsed dead time 0.427 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 1.001 s
FEE module #: 6 elapsed dead time 3.508 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.053 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.000 s
FEE module #: 12 elapsed dead time 0.000 s
FEE module #: 13 elapsed dead time 0.100 s
FEE module #: 14 elapsed dead time 0.164 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.264 s
FEE module #: 18 elapsed dead time 0.000 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.000 s
FEE module #: 21 elapsed dead time 0.028 s
FEE module #: 22 elapsed dead time 0.171 s
FEE module #: 23 elapsed dead time 0.000 s
FEE module #: 24 elapsed dead time 0.000 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 15.730s ( 2034.269 blocks/s, 127.142 Mb/s)
14.54 R11 stopped (two DAQ STOP commands required)
15.00 New firmware version 8.24 installed (/MIDAS/Aida/FEE_GF_Feb16_24.bin)
- guarantee SYNC is the last data item with timestamp ending 0x000000A0 to be output (merger assumes this)
- ASIC clock runs when output disabled (ASIC requires periodic reset)
18.40 R13 starts
ASIC settings 2016Sep02-18.17.01
Discriminator masks -> 0x0
Correlation scaler trigger delay 0x180 -> 0x5 |
|
Fri Nov 2 00:57:24 2018, CA, CB, TD, OH, Friday 2 November 14x
|
09.58 DAQ continues OK - current file Oct18/R15_6
alpha background run
09.20 all system wide checks OK *except*
nnaida7 fails ADC calibration
SYNC errors since baseline - see attachment 1 - baseline not zero'd following reboot of nnaida2 and
setup of all FEE64s yesterday
SYNC errors OK following new baseline check
detector biases & leakage currents OK - see attachments 2 & 3
FEE64 temperatures OK - see attachment 4
good event statistics OK - see attachment 5
nnaida2 rate due to one hot channel
Merger OK - see attachment 6
TapeServer OK - see attachment 7
no errors or warnings shown by server terminal sessions
1.8.L spectra - see attachments 8 & 9
N.B. evidence of minimally ionising particles (presumably protons) from beam to F11 E detector
~10-15cm Pb bricks were placed within BRIKEN (CH2)n stack to stop heavy particles
1.8.W spectra - see attachments 10 & 11 - trace updates for 9/12 p+n FEE64s have stopped, n+n FEE64s OK
15.54 DAQ continues - current file Oct18/R15_15
nnaida17 good event rate c. 400kHz
15.57 FEE64 reset, setup, system wide checks
all ASIC clocks sync'd using ReSYNC
all spectra zero'd
ASIC check load
DAQ go - data transfer disabled
good events statistics - attachment 12
1.8.W spectra - see attachments 13 & 14
changed LED threshold 7700 -> 8500 for 9/12 p+n FEE64s |
|
Fri Jun 2 00:01:48 2017, OH, PW, CB, Friday 2 June 08:00-16:00 9x
|
08:05 Briken and BigRIPS stopping daqs
AIDA on file R1_1099
08:07 BigRIPS starts run 1088
BRIKEN starts run 77
08:13 System wide checks all ok
FEE temperatures all ok - attachment 1
Good events statistics - attachment 2
08:50 Bias and leakage currents ok - attachment 3
09:04 BigRIPS and BRIKEN stop daqs
AIDA on file R1_1113
09:05 BigRIPS starts run 1089
BRIKEN starts run 78
AIDA on file R1_1113
09:22 Beam lost AIDA on file R1_1117
09:26 Beam back AIDA on file R1_1118
10:06 BigRIPS and BRIKEN stop daqs
AIDA on file R1_1128
10:07 BigRIPS starts run 1090
BRIKEN starts run 79
AIDA on file R1_1128
10:12 System wide checks ok
10:24 DSSD rates from R1_1131
*** DSSSD # 1 count: 88384 old count: 45978 dt: 1.01 s LEC rate: 42084.25 Hz
*** DSSSD # 2 count: 119845 old count: 62135 dt: 1.01 s LEC rate: 57272.13 Hz
*** DSSSD # 3 count: 40809 old count: 21150 dt: 1.01 s LEC rate: 19509.84 Hz
*** DSSSD # 4 count: 37059 old count: 18986 dt: 1.01 s LEC rate: 17935.87 Hz
*** DSSSD # 5 count: 14947 old count: 7772 dt: 1.01 s LEC rate: 7120.56 Hz
*** DSSSD # 6 count: 29809 old count: 15349 dt: 1.01 s LEC rate: 14350.29 Hz
*** DSSSD # 1 count: 35 old count: 16 dt: 1.01 s HEC rate: 18.86 Hz
*** DSSSD # 2 count: 108 old count: 56 dt: 1.01 s HEC rate: 51.61 Hz
*** DSSSD # 3 count: 77 old count: 38 dt: 1.01 s HEC rate: 38.70 Hz
*** DSSSD # 4 count: 76 old count: 35 dt: 1.01 s HEC rate: 40.69 Hz
*** DSSSD # 5 count: 27 old count: 15 dt: 1.01 s HEC rate: 11.91 Hz
*** DSSSD # 6 count: 4 old count: 2 dt: 1.01 s HEC rate: 1.98 Hz
11:07 BigRIPS and BRIKEN stop their daqs
AIDA on file R1_1142
11:08 BigRIPS starts run 1091
BRIKEN starts run 80
AIDA on file R1_1142
11:10 Leakages and biases ok - attachment 4
11.36 DAQ continues OK
Attached HEC x vs y - attach 5
Zero'd HEC x vs y
11.59 Analysed R1_1153 - see attachment 6
No timewarps
Dead time negligible
All OK
12:06 BigRIPS and BRIKEN stop their daqs
AIDA on file R1_1156
12:07 BigRIPS starts run1092
BRIKEN starts run 81
AIDA on file R1_1156
13:07 BigRIPS and BRIKEN stop daqs
AIDA on file R1_1170
13:08 BRIKEN starts run 82
BigRIPS starts run 1093
AIDA on file R1_1170
13:11 System wide checks ok
13:55 BRIKEN and BigRIPS stop their daqs
AIDA on file R1_1181
Beam gone
14:11 Bias and leakage currents ok - attachment 7
Ambient Temperature 23.9C - Humidity 37.3% - D.P +8.3
15:26 Beam is back
AIDA on file R1_1201
15:07 BigRIPS starts run 1094
BRIKEN starts run 83
AIDA on file R1_1201
15:34 System wide checks ok
FEE temperatures ok - attachment 8
Good Events statistics - attachment 9
15:39 No beam - beam back
15:46 Beam gone for couple of minutes
15:50 Beam back |
|
Thu Jun 1 16:06:03 2017, NN, Friday 2 June 00:00-08:00 14x
|
00:35 Beam is on
current AIDA file R1_996
00:36 BRIKEN start run 72
BigRIPS start run 1083
AIDA file RIBF127R1/R1_996
00:55 Beam is off but DAQ of BRIKEN and BigRIPS are still running)
expecting it will be back within 10 minutes
AIDA file R1_1001
00:57 Analysis of file RIBF127R1/R1_1000 - dead time < 0.4% - see attachment 1
01:03 Beam is on
DAQ is running continuously
01:15 statistics normal
system wide checks ok
leakage current and bias ok see attachment 2
merger and tapeserver ok
01:25 BigRIPS and BRIKEN stop their runs
current AIDA run R1_1007
01:26 BRIKEN start run 73
BigRIPS start run 1084
AIDA on file R1_1008
01:36 FEE temperature is normal see attachment 3
02:22 BigRIPS and BRIKEN stop their runs
current AIDA run R1_1021
02:23 high energy correlation between x and y attachment 4
AIDA run R1_1021
02:26 BRIKEN start run 74
BigRIPS start run 1085
AIDA on file R1_1023
03:00 System wide checks all ok
FEE temperatures ok - attachment 5
Good event statistics - attachment 6
Merger and tape server still running - attachment 7
03:06 Leakages and bias ok - attachment 8
03:09 Beam is OFF
03:11 BigRIPS and BRIKEN stop their runs
current AIDA run R1_1033
04:10 Beam is still OFF
Investigation is still going on, on the ion source.
(Ion source were getting down more and more frequently before)
04:49 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok
merger and tapeserver ok
(waiting beam)
06:01 Beam is ON
AIDA run R1_1069
06:02 BRIKEN start run 75
BigRIPS start run 1086
AIDA on file R1_1070
06:08 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok see attachment 9
merger and tapeserver ok
06:20 Analysis of file RIBF127R1/R1_1072 - dead time < 0.6% (most of the FEE cards have 0.0%) - see attachment 10
07:01 high energy correlation between x and y attachment 11
AIDA run R1_1084
07:02 BigRIPS and BRIKEN stop their runs
current AIDA run R1_1084
07:04 BRIKEN start run 76
BigRIPS start run 1087
AIDA on file R1_1085
07:16 per DSSSD rates file RIBF127R1/R1_1086
*** DSSSD # 1 count: 92842 old count: 41280 dt: 1.05 s LEC rate: 49071.92 Hz
*** DSSSD # 2 count: 124879 old count: 56250 dt: 1.05 s LEC rate: 65314.71 Hz
*** DSSSD # 3 count: 44779 old count: 19466 dt: 1.05 s LEC rate: 24090.56 Hz
*** DSSSD # 4 count: 37971 old count: 18208 dt: 1.05 s LEC rate: 18808.59 Hz
*** DSSSD # 5 count: 15612 old count: 7434 dt: 1.05 s LEC rate: 7783.06 Hz
*** DSSSD # 6 count: 31207 old count: 14708 dt: 1.05 s LEC rate: 15702.22 Hz
*** DSSSD # 1 count: 27 old count: 11 dt: 1.05 s HEC rate: 15.23 Hz
*** DSSSD # 2 count: 89 old count: 43 dt: 1.05 s HEC rate: 43.78 Hz
*** DSSSD # 3 count: 82 old count: 44 dt: 1.05 s HEC rate: 36.16 Hz
*** DSSSD # 4 count: 65 old count: 32 dt: 1.05 s HEC rate: 31.41 Hz
*** DSSSD # 5 count: 29 old count: 17 dt: 1.05 s HEC rate: 11.42 Hz
*** DSSSD # 6 count: 6 old count: 3 dt: 1.05 s HEC rate: 2.86 Hz
07:22 FEE's temperature normal - see attachment 12
statistics normal - see attachment 13
system wide checks ok
leakage current and bias ok
merger and tapeserver ok - see attachment 14 |
|
Thu Dec 1 16:01:10 2016, CG, PV, Friday 2 December 14x
|
00.07 BigRIPS data file 1135
01.07 BigRIPS data file 1136.
02.09 BigRIPS data file 1137.
02.13 Beam off. ~1/2 way through R44_137
02.16 Beam back. ~600MB into R44_139
BigRIPS data file 1138.
03.17 BigRIPS data file 1139.
03.37 Beam stopped. End of R44_167.
03.43 Beam returned to F11. ~700MB through R44_170.
BigRIPS data file 1140.
04.00 Beam off for stripper foil change. End of R44_175.
04.06 Beam returned to F11. 1.2GB into R44_178.
04.08 BigRIPS data file 1141.
05.09 BigRIPS data file 1142.
06.02 BigRIPS data fill 1143.
06.26 R44 stopped @ R44_227 ahead of LN2 fill.
07.02 BigRIPS data file 1144.
07.43 Run R45 started.
08.02 BigRIPS data file 1145.
08.05 Local Elog and BigRIPS log uploaded (attachments 3-6).
09.00 Machine time ended, the last data file is R45_18
13.40 Biases are shown as attachments 7 and 8
15.04 DAQ starts (RIBF03R1/R46)
Pulser walkthrough
Amplitude 90,000 - 10,000 @ 10,000 step
x5 attenuator IN
t_r 50ns tau_d 50us
frequency 250Hz range
polarity -, tail pulse, delay MIN
15.19 Walk through finishes. See attachments 9 and 10 for histograms
15.26 DAQ starts (RIBF03R1/R47)
Pulser walkthrough
Amplitude 12,000 - 2,000 @ 2,000 step
15.35 R47_2 finishes.
See attachments 11 and 12 for histograms
15.41 DAQ starts (RIBF03R1/R48)
Background - BNC PB-4 pulser OFF
16.35 DAQ stops OK (RIBF03R1/R48_13)
16.55 DSSSD bias & leakage currents Ok - see attachment 13 & 14
Ambient temperature +25.2 deg C, -4.2 deg C, RH 14.2% |
|
Fri May 19 02:44:14 2017, TD, CB, OH, Friday 19th May
|
10:44 System wide checks all ok
Leakages and biases all ok (see attachment 1)
Ambient Temperature 24.4C - Humidity 38.1% - Dew Point +9.1
FEE temperatures ok (see attachment 2)
DAQ, Merger and Tape server all still running ok
Good events statistics (see attachment 3)
Orientation of RS-232 cards was wrong. They have now been corrected will enable logging then do a halt and
go on the daq.
Power supply also moved onto AIDA circuit.
11:00 Current file R15_333.
11:04 halt and go performed
24 Log files produced on Rasp Pi console monitor. |
|
Fri Aug 19 07:42:22 2016, TD, PV, Friday 19 August 6x
|
14.00 Both AIDA NIM bins U/S
Upper NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B - ac mains fuse 100V/8A/slow? blowing
Lower NIM bin - 11x MACB - not powering up
Replaced both NIM bins.
Upper NIM bin - 11x MACB
Lower NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B
15.50 Julabo FL11006 chiller ON - set point +20 deg C
B2F/F11 ambient temp +24.0 deg C, RH 54%, DP +13.8 deg C
Bias 6x MSL type BB18 DSSSDs - see attachments 1-2
16.10 Startup DAQ nnaida1-24 *except* nnaida19
System-wide checks
Check clock status OK
Check ADC calibration - nnaida7 failed
Check ASIC clock timestamp - multiple failures - see attachment 3
Check SYNC errors not counted Since Baseline - see attachment 4
Check SYNC pulses received - see attachment 5
BNC PB-4
Amplitude 90,000, x5 attenuator IN
t_r 50ns, tau_d 50us
Polarity -
INT ref, delay MIN, tail pulse
FEE64 temperatures - see attachment 6
16.34 R1 starts (directory Aug2016)
slow comparator 0x10, LEC/MEC fast comparator 0x10
merge 555k data items/s, tapeserver 4430 kb/s
18.28 R4 starts
Settings per R1
18.31 DAQ/merge stalls with (many) messages as follows
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
Merge state now Paused
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in pending data, found 1146,
last 575
copyItems: queue 14, maybe copied in wrong buffer: sequence 1146, last 575
Merge_addItems: queue 14, maybe added wrong buffer: sequence 1146, last 575
MERGE Program (24316): check_for_data: index 14, unexpected header sequence number in new data, found 689, last 1258
copyItems: queue 14, maybe copied in wrong buffer: sequence 689, last 1258
Merge_addItems: queue 14, maybe added wrong buffer: sequence 689, last 1258
MERGE Data Link (24254): client closed connection
MERGE Data Link (24254): listening on port 11001
MERGE Data Link (24255): client closed connection
MERGE Data Link (24255): listening on port 11002
MERGE Data Link (24257): client closed connection
MERGE Data Link (24257): listening on port 11004
MERGE Data Link (24258): client closed connection
MERGE Data Link (24258): listening on port 11005
MERGE Data Link (24261): client closed connection
MERGE Data Link (24261): listening on port 11008
MERGE Data Link (24260): client closed connection
MERGE Data Link (24260): listening on port 11007
MERGE Data Link (24259): client closed connection
MERGE Data Link (24259): listening on port 11006
MERGE Data Link (24256): client closed connection
MERGE Data Link (24256): listening on port 11003
MERGE Data Link (24262): client closed connection
MERGE Data Link (24262): listening on port 11009
MERGE Data Link (24263): client closed connection
MERGE Data Link (24263): listening on port 11010
MERGE Data Link (24265): client closed connection
MERGE Data Link (24265): listening on port 11012
MERGE Data Link (24266): client closed connection
MERGE Data Link (24266): listening on port 11013
MERGE Data Link (24267): client closed connection
MERGE Data Link (24267): listening on port 11014
MERGE Data Link (24269): client closed connection
MERGE Data Link (24269): listening on port 11016
MERGE Data Link (24268): client closed connection
MERGE Data Link (24268): listening on port 11015
MERGE Data Link (24270): client closed connection
MERGE Data Link (24270): listening on port 11017
MERGE Data Link (24264): client closed connection
MERGE Data Link (24264): listening on port 11011
MERGE Data Link (24273): client closed connection
MERGE Data Link (24273): listening on port 11020
MERGE Data Link (24271): client closed connection
MERGE Data Link (24271): listening on port 11018
MERGE Data Link (24277): client closed connection
MERGE Data Link (24277): listening on port 11024
MERGE Data Link (24275): client closed connection
MERGE Data Link (24275): listening on port 11022
MERGE Data Link (24274): client closed connection
MERGE Data Link (24274): listening on port 11021
MERGE Data Link (24276): client closed connection
MERGE Data Link (24276): listening on port 11023 |
 Fri Aug 19 09:43:27 2016, TD, VP, reply PJCS, Friday 19 August
|
>
> 14.00 Both AIDA NIM bins U/S
> Upper NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B - ac mains fuse 100V/8A/slow? blowing
> Lower NIM bin - 11x MACB - not powering up
>
> Replaced both NIM bins.
> Upper NIM bin - 11x MACB
> Lower NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B
>
> 15.50 Julabo FL11006 chiller ON - set point +20 deg C
> B2F/F11 ambient temp +24.0 deg C, RH 54%, DP +13.8 deg C
>
> Bias 6x MSL type BB18 DSSSDs - see attachments 1-2
>
> 16.10 Startup DAQ nnaida1-24 *except* nnaida19
>
> System-wide checks
>
> Check clock status OK
> Check ADC calibration - nnaida7 failed
> Check ASIC clock timestamp - multiple failures - see attachment 3
> Check SYNC errors not counted Since Baseline - see attachment 4
> Check SYNC pulses received - see attachment 5
>
> BNC PB-4
>
> Amplitude 90,000, x5 attenuator IN
> t_r 50ns, tau_d 50us
> Polarity -
> INT ref, delay MIN, tail pulse
>
> FEE64 temperatures - see attachment 6
>
> 16.34 R1 starts (directory Aug2016)
>
> slow comparator 0x10, LEC/MEC fast comparator 0x10
>
> merge 555k data items/s, tapeserver 4430 kb/s
Looks like a problem with the inter-MACB wiring.
The screen shots show groups of 4 with the problems.
I suggest re-seating the short HDMI cables and reset the system. |
|
Fri Aug 19 11:07:44 2016, TD, VP, reply PJCS, Friday 19 August
|
> >
> > 14.00 Both AIDA NIM bins U/S
> > Upper NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B - ac mains fuse 100V/8A/slow? blowing
> > Lower NIM bin - 11x MACB - not powering up
> >
> > Replaced both NIM bins.
> > Upper NIM bin - 11x MACB
> > Lower NIM bin - BNC PB-4, Ortec 433, 2x CAEN N1419, 1x CAEN N1419B
> >
> > 15.50 Julabo FL11006 chiller ON - set point +20 deg C
> > B2F/F11 ambient temp +24.0 deg C, RH 54%, DP +13.8 deg C
> >
> > Bias 6x MSL type BB18 DSSSDs - see attachments 1-2
> >
> > 16.10 Startup DAQ nnaida1-24 *except* nnaida19
> >
> > System-wide checks
> >
> > Check clock status OK
> > Check ADC calibration - nnaida7 failed
> > Check ASIC clock timestamp - multiple failures - see attachment 3
> > Check SYNC errors not counted Since Baseline - see attachment 4
> > Check SYNC pulses received - see attachment 5
> >
> > BNC PB-4
> >
> > Amplitude 90,000, x5 attenuator IN
> > t_r 50ns, tau_d 50us
> > Polarity -
> > INT ref, delay MIN, tail pulse
> >
> > FEE64 temperatures - see attachment 6
> >
> > 16.34 R1 starts (directory Aug2016)
> >
> > slow comparator 0x10, LEC/MEC fast comparator 0x10
> >
> > merge 555k data items/s, tapeserver 4430 kb/s
> Looks like a problem with the inter-MACB wiring.
> The screen shots show groups of 4 with the problems.
> I suggest re-seating the short HDMI cables and reset the system.
Short HDMI cables re-seated. See attachment 1 |
|