| ID |
Date |
Author |
Subject |
|
599
|
Thu May 25 02:11:04 2017 |
CB, TD | Thursday 25 May | 10.10 DAQ continues OK
Current file May2017/R26_17
Detector biases; leakage currents OK - see attachment 1
FEE64 Temperatures OK - see attachment 2
good events; statistics OK - see attachment 3
No warnings/errors reported by merger since DAQ GO - see attachment 4
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
10.17 E17/F11 ambient temperature +24.2 deg C, RH 42.8%, d.p. +10.7 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 70%)
Lights on B2 partially off - Alvaro TD reports this may imply beam tests being carried out. He also
reports spike of gamma counts in BRIKEN clover around 10:00.
10.18 DAQ stops OK
Current file May2017/R26_17
Zeroed histograms. Background alpha calibration long run ongoing.
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x64
LEC/MEC fast comparator 0x20
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
10.25 DAQ stars OK
Current file may2017/R27
ttyUSB7 (nnaida1) attached
10.50 Measured AIDA ac mains voltage with DMM. Voltage 100.4V rms L-N
FL11006 chiller refilled (2 litres added)
17.05 DAQ continues OK
Current file May2017/R26_17
Detector biases; leakage currents OK - see attachment 6,7
FEE64 Temperatures OK - see attachment 8
good events; statistics OK - see attachment 9
No warnings/errors reported by merger since DAQ GO - see attachment 10
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
17.07 E17/F11 ambient temperature +24.1 deg C, RH 39.8%, d.p. +9.5 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 95%)
Left DAQ running on alpha background calibration run
|
|
700
|
Fri Nov 17 10:03:25 2017 |
CB, TD | Friday 17 November | 19.03 DAQ started OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa
Detector biases & leakage currents OK - see attachments 1
FEE64 Temperatures OK - see attachment 2
DAQ statistics OK - see attachment 3
*all* system wide checks OK *except* nnaida7 fails ADC calibration
Rate look OK. A few dropped channels. See attach 4
Waveforms look OK. Noise at reasonable levels. See attach 5 & 6
19:15 Started run Nov17/R1
Kbyte/sec written 2611
Merger data rate 346210 items/sec
19:26 Observed increase in rate in asics nnaida13, 19 (>50 000)
Noise profile looks typical. See waveforms - attach 7,8
Increased FEE64 slow comparators for nnaida 13, 19 from 0xa to 0xc
Rate decreases significantly. See attach 9
19.40 Beam on
BigRIPS 115Nb setting
WAS3ABI + YSO
Good Event, merger and data rates OK - see attachments 10-12
8x FEE64s <10k
8x FEE64s 10-20k
6x FEE64s 20-30k
2x FEE64s 30-40k
19.57 per FEE64 1.8.W spectra (2ms FSR) - see attachments 14-15
20.06 per FEE64 1.8.L spectra - see attachments 16-17
nnaida17 67 ch FWHM
nnaida8 73 ch FWHM
20.50 DAQ starts
RIKEN run: 005
Wasabi Run: 4048
BigRIPS run: 2057
AIDA run R2_0
Listmode DLT file:171117_2050_115Nb_005.dlt
BRIKEN Rate (h:12): ~ 42 cps
F11 Rate (h:18): ~ 37 cps
CLOVERS Rate (h:15): ~ 33 cps
AIDA Veto Plastic Rate (h:19): ~ 23
WAS3ABi in
YSO removed
AIDA inserted to HPGe clover cryostat position
BigRIPS 115Nb setting
Degrader 5mm Al
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xf, nnaida19 0xc, nnaida20-21 0xb
20.57 all spectra zero'd
Good Event stats - see attachment 18
7x FEE64s <10k
5x FEE64s 10-20k
4x FEE64s 20-30k
4x FEE64s 30-40k
3x FEE64s 40-50k
1x FEE64 >50k (nnaida13 73k)
21.22 Not all ASICs settings restored from 2017Oct23-14.38.03
Some p+n FEE64s Ibias LF feedback 0x8 *not* 0xf as expected - now changed manually
AIDA data file Nov17/R2_5
ASIC settings saved to 2017Nov17-21.24.47
Updated options
21.33 New BigRIPS, BRIKEN, WAS3ABi files started
AIDA continues from R2_6
Date: 17/11/017
Start: 2133
RIKEN run: 006
Wasabi Run: 4061
BigRIPS run: 2058
AIDA run R2_06
Listmode DLT file:171117_2132_115Nb_006.dlt
BRIKEN Rate (h:12): ~ 42 cps
F11 Rate (h:18): ~ 37 cps
CLOVERS Rate (h:15): ~ 33 cps
AIDA Veto Plastic Rate (h:19): ~ 23
21.40 Detector biases & leakage currents OK - see attachments 19 & 20
FEE64 Temperatures OK - see attachment 21
DAQ statistics OK - see attachment 22
*all* system wide checks OK *except* nnaida7 fails ADC calibration
per FEE64 1.8.* spectra (20ms FSR) see attachments 23 & 24
p+n spectra now look OK with Ibias LF feedback changed from 0x8 to 0xf
note 3kHz appears in nnaida19, 21 & 22
22.41 DAQ stop
AIDA data file Nov17/R2_15
*use R2_8 - R2_15* for offline analysis
22.50 AIDA withdrawn from BRIKEN
YSO re-installed
23.10 Detector biases & leakage currents OK - see attachments 25 & 26
FEE64 Temperatures OK - see attachment 27
DAQ statistics OK - see attachment 28
7x FEE64s <10k
4x FEE64s 10-20k
8x FEE64s 20-30k
2x FEE64s 30-40k
2x FEE64s 40-50k
1x FEE64 >50k (nnaida13 64k)
*all* system wide checks OK *except* nnaida7 fails ADC calibration
per FEE64 1.8.W spectra (20ms FSR) - see attachments 29 & 30
per FEE64 rate spectra linear and log scales - see attachments 31 & 32
23.30 all spectra zero'd |
|
703
|
Sat Nov 18 04:25:16 2017 |
CB, TD | Saturday 18 November |
13.27 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
7x FEE64s <10k
4x FEE64s 10-20k
6x FEE64s 20-30k
4x FEE64s 30-40k
2x FEE64s 40-50k
1x FEE64 >50k (nnaida13 64k)
*all* system wide checks OK *except* nnaida7 fails ADC calibration
13.50 all spectra zero'd
*all* ASIC slow comparator settings -> 0xa
DAQ statistics - see attachment 5
17:05 1.*.W spectra for front strips attached - see attach 6-17
Layout 3 & 4 - see attach 18,19
nnaida1 Peak width = 79.68+/- 0.3080, Peak area = 189026.00+/- 434.77
nnaida2 Peak width = 126.52+/- 1.0035, Peak area = 180119.00+/- 426.09
nnaida5 Peak width = 79.16+/- 1.1547, Peak area = 189192.00+/- 434.96
nnaida6 Peak width = 78.30+/- 0.2948, Peak area = 189316.00+/- 435.10
nnaida9 Peak width = 77.54+/- 0.2578, Peak area = 189201.00+/- 434.97
nnaida10 Peak width = 88.96+/- 0.7201, Peak area = 189252.00+/- 435.03
nnaida13 Peak width = 225.44+/- 0.6773, Peak area = 178047.00+/- 421.96
nnaida14 Peak width = 81.43+/- 0.5754, Peak area = 188275.50+/- 435.05
nnaida17 Peak width = 74.42+/- 0.3670, Peak area = 189139.00+/- 434.90
nnaida18 Peak width = 78.13+/- 2.1601, Peak area = 188683.00+/- 436.03
nnaida21 Peak width = 155.44+/- 0.7619, Peak area = 183728.00+/- 428.64
nnaida22 Peak width = 120.95+/- 0.3604, Peak area = 184462.00+/- 429.49
nnaida3 Peak width = 80.08+/- 0.1346, Peak area = 190083.00+/- 435.99
nnaida4 Peak width = 82.15+/- 0.1403, Peak area = 190143.00+/- 436.0
nnaida7 Peak width = 87.46+/- 0.6821, Peak area = 190314.00+/- 436.25
nnaida8 Peak width = 69.86+/- 1.0958, Peak area = 189915.50+/- 437.33
nnaida11 Peak width = 99.95+/- 0.2553, Peak area = 188884.00+/- 436.10
nnaida12 Peak width = 101.40+/- 0.2937, Peak area = 188737.00+/- 436.02
nnaida15 Peak width = 78.17+/- 1.8691, Peak area = 188912.00+/- 436.61
nnaida16 Peak width = 107.16+/- 1.1332, Peak area = 190392.00+/- 436.34
nnaida19 Peak width = 137.14+/- 0.2579, Peak area = 186414.50+/- 432.426
nnaida20 Peak width = 128.06+/- 0.9060, Peak area = 185287.00+/- 437.16
nnaida23 Peak width = 103.67+/- 0.3636, Peak area = 190221.00+/- 436.14
nnaida24 Peak width = 99.72+/- 0.4577, Peak area = 189176.00+/- 436.85 |
|
704
|
Sun Nov 19 01:46:10 2017 |
CB, TD | Sunday 19 November | 10.45 Detector biases & leakage currents OK - see attachments 1
FEE64 Temperatures OK - see attachment 2
DAQ statistics OK - note *all* slow comparators 0xa - see attachment 3
7x FEE64s <10k
4x FEE64s 10-20k
4x FEE64s 20-30k
4x FEE64s 30-40k
1x FEE64s 40-50k
4x FEE64 >50k
*all* system wide checks OK *except* nnaida7 fails ADC calibration
14.05 *all spectra zero'd
14.24 Detector biases & leakage currents OK - see attachments 4 & 5
FEE64 Temperatures OK - see attachment 6
DAQ statistics OK - see attachment 7
7x FEE64s <10k
3x FEE64s 10-20k
4x FEE64s 20-30k
5x FEE64s 30-40k
1x FEE64s 40-50k
4x FEE64 >50k
*all* system wide checks OK *except* nnaida7 fails ADC calibration
per FEE64 rate, 1.8.L and 1.8.W spectra (20ms FSR) - see attachments 8-13
14.48 MONLOCK monitor - see attachment 14 |
|
833
|
Sat Jun 8 06:08:52 2019 |
CB, TD | Saturday 8 June | 14.14 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C
Water level c. 70% M-H markers
Temperature +25.3 deg C dew point +8.5 deg C RH 34.7%
DAQ continues OK
ASIC settings 2019May19-17.54.03
slow comparator 0xa
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachments 4
13x <20k 22x < 50k 24x <100k cf. 13x <20k 21x < 50k 24x <100k yesterday afternoon
Merger OK - see attachment 5
TapeServer OK - see attachment 6
p+n FEE64s 1.8.W spectra 20us FSR - attachment 7
n+n FEE64s 1.8.W spectra 20us FSR - attachment 8
1.8.L spectra - see attachments 9 & 10
nnaida1 104 ch FWHM, nnaida3 111 ch FWHM - cf. 80 & 87 ch FWHM respectively yesterday aftenoon
FEE64 Rate spectra - attachment 11
Check ASIC Control *all* FEE64s & ASICs x2
FEE64 Rate spectra - attachment 12 - some channels recovered
14.29 ADC data synchronised - attachment 13
14.31 zero all histograms
zero DAQ stats |
|
632
|
Sun Jun 4 23:50:24 2017 |
CB, PW, DK, TD | Monday 5 June 08:00 to 16:00 | 07:50 Leakage currents OK - attachment 1
FEE64 temperatures OK - attachment 2
Good event statistics OK - attachment 3
No new merger errors - attachment 4
HEC x vs y plot OK - attachment 5
Zero'd SortSas
Sorted run RIBF148/R2_375. DSSD rates as follows
Pulser still synchronised - attachment 6
*** data items: 13911095 ( 120732.29 Hz)
*** ADC events: 1173612 ( 10185.60 Hz)
*** time warps: 0 ( 0.00 Hz)
*** DSSSD # 1 count: 546264 old count: 529893 dt: 11.53 s LEC rate: 47387.36 Hz
*** DSSSD # 2 count: 811805 old count: 787055 dt: 11.53 s LEC rate: 70422.54 Hz
*** DSSSD # 3 count: 308448 old count: 297268 dt: 11.53 s LEC rate: 26757.28 Hz
*** DSSSD # 4 count: 246100 old count: 238286 dt: 11.53 s LEC rate: 21348.71 Hz
*** DSSSD # 5 count: 148961 old count: 143967 dt: 11.53 s LEC rate: 12922.08 Hz
*** DSSSD # 6 count: 240995 old count: 233066 dt: 11.53 s LEC rate: 20905.86 Hz
*** DSSSD # 1 count: 0 old count: 0 dt: 11.53 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 19 old count: 18 dt: 11.53 s HEC rate: 1.65 Hz
*** DSSSD # 3 count: 5 old count: 5 dt: 11.53 s HEC rate: 0.43 Hz
*** DSSSD # 4 count: 32 old count: 26 dt: 11.53 s HEC rate: 2.78 Hz
*** DSSSD # 5 count: 70 old count: 70 dt: 11.53 s HEC rate: 6.07 Hz
*** DSSSD # 6 count: 1403 old count: 1354 dt: 11.53 s HEC rate: 121.71 Hz
Analysed run R2_375. 6 MBS related errors messages, but no MBS timewarps. See attachment 7
08:01 BRIKEN and BigRIPS stopping run
AIDA on run RIBF148/R2_378
08:03 BRIKEN starts run 25
BigRIPS starts run 24
AIDA on run RIBF148/R2_379
08:26 All system wide checks OK *except* nnaida1 clock status (6), ADC calibration for nnaida1, 21
08:26 BRIKEN and BigRIPS stopping run
AIDA on run RIBF148/R2_387
08:26 Completely removing degraders
08:39 BRIKEN starts run 26
BigRIPS starts run 25
AIDA on run RIBF148/R2_388
Zero'd SortSas
08:55 HEC x vs y plot - attachment 8
09:00 BRIKEN and BigRIPS stopping run
AIDA on run RIBF148/R2_394
Rare earths first run ends here.
09:01 Stopped DAQ
09:20 Rebuilt lead wall in front of AIDA
T = 24.9C RH = 23.7% DP = 3.6C
Julabo Chiller at 75%. Refilled.
11:13 Restarted DAQ
Checkload x2 - All OK
Current run /TapeServer/RIBF128/R1_1
All OK
11:19 Starting run RIBF128/R2_1
High-amplitude pulser walkthrough 90 000, 80 000 ... 10 000
Frequency 250 Hz
11:31 Starting run RIBF128/R3_1
Low-amplitude pulser walkthrough 12 000, 10 000 ... 2 000
Frequency 250 Hz
Set pulser amplitude back to 90 000, frequency to 25 Hz
Stopped run
11:41 Starting new run RIBF128/R4_1
Background run at present
13.56 Detector biases & leakage currents OK - see attachments 9 & 10
FEE64 Temperatures OK - see attachment 11
good events statistics OK - see attachment 12
No warnings/errors reported by merger since DAQ GO - see attachment 13
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (status=6)
14.30 analysis of file RIBF128/R4_25 - dead time < 0.5% - see attachment 14
14.32 online analysis - ADC data synchronised - see attachment 15
15:08 Merger log shows repeated timewarps - attachment 16
Seems to have stopped now.
15:10 Analysed R4_38. 9 MBS timewarps.
Other parameters as normal
15:14 Analysed R4_39. 4 MBS timewarps.
Other parameters as normal.
15:19 ttyUSB18 (nnaida6) attached - attachment 17
Log is extremely large and contains several repetitions of one error message
TCP transfer library version 3.12
TCP socket send buffer was 16384 - now 221184
TCP socket receive buffer was 87380 - now 221184
TCP socket created OK - now connecting to myserver port 11006
Transfer Error - : Connection refused
connect() failed:
TCP transfer library version 3.12
TCP socket send buffer was 16384 - now 221184
TCP socket receive buffer was 87380 - now 221184
TCP socket created OK - now connecting to myserver port 11006
Transfer Error - : Connection refused
connect() failed:
TCP transfer library version 3.12
TCP socket send buffer was 16384 - now 221184
TCP socket receive buffer was 87380 - now 221184
TCP socket created OK - now connecting to myserver port 11006
Transfer Error - : Connection refused
15:25 Merger crashed. Stopped merger. Stopped tape server.
Merger shows all links bright green, except nnaida 2 - see attachment 20
Statistics show a counting spike in nnaida 2 - see attachment 21
15:33 Cannot reset the DAQ - see attachment 22
15:40 System console log for nnaida2 attached - see attach 23
15:54 Power cycled FEEs
Waited 10 minutes. nnaida13 did not mount /nfs - see attached log (attach 24)
16:07 Power cycled FEEs again. Managed to restart the DAQ. |
|
601
|
Fri May 26 02:20:42 2017 |
CB, OH, NN | Friday 26 May | 10.20 DAQ continues OK
Current file May2017/R27_22
Detector biases; leakage currents OK - see attachment 1
FEE64 Temperatures OK - see attachment 2
good events; statistics OK - see attachment 3
No warnings/errors reported by merger since DAQ GO - see attachment 4
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
10.30 E17/F11 ambient temperature +24.2 deg C, RH 39.7%, d.p. +9.7 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 75%)
Left DAQ running on alpha background calibration run
ttyUSB7 log (nnaida1) attached
GUI got stuck while attempting to drag-and-drop ttyUSB7 to ELOG to upload. Terminal still working and
confirmed Merger working OK.
Killed nautilus process to get GUI unstuck. Uploaded ttyUS7 via Browse -> Upload button on ELOG instead.
15.51 DAQ continues OK
Current file May2017/R27_28
Detector biases; leakage currents OK - see attachment 6
FEE64 Temperatures OK - see attachment 7
good events; statistics OK - see attachment 8
No warnings/errors reported by merger since DAQ GO - see attachment 9
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (=6)
15.53 E17/F11 ambient temperature +24.1 deg C, RH 40.1%, d.p. +9.8 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 75%)
Left DAQ running on alpha background calibration run
ttyUSB7 log (nnaida1) attached
19.20 DAQ continues OK
Current file May2017/R27_31
Detector biases; leakage currents OK - see attachment 11 & 12
FEE64 Temperatures OK - see attachment 13
good events; statistics OK - see attachment 14
No warnings/errors reported by merger since DAQ GO - see attachment 15
*all* system wide checks OK *except* ADC calibration of nnaida1, 21 and nnaida1 clock status (status=6)
19.30 E17/F11 ambient temperature +24.2 deg C, RH 38.5%, d.p. +9.2 deg C |
|
843
|
Sat Jun 15 16:53:22 2019 |
CB, OH, DK, ML | Sunday 16 June |
00.30 AIDA file R2_26
DTAS run 007
BigRIPS run 2006
00:55
Merger status - attachment 1
TapeSever status - attachment 2
01:40
Before zeroing stats - attachment 3
Histos up to now saved in /homes/npg/spectra/specs-2019Jun16-01.46.50
Before zeroing histos - XY attachment 4
02:22 Up to AIDA R2_41
Stats - attachment 5
XY implants - attachment 6
02:29 AIDA R2_42
DTAS run 011
BigRIPS still 2006
04:08 Up to AIDA R2_55
Temps - attachment 7
Biases - attachment 8
Stats - attachment 9
XY implants - attachment 10
04:50 Did some major UI updates to merger /data02/2019data/dtas/scripts/parallelscript/runall_xe19_dev.sh
If no parameters are passed, it asks to select each option one-by-one, showing available options
For DTAS, if there is only one run for a given header, it automatically selects it
After that, it checks that all the raw files actually exist
Finally, it composes the command, asks the user if it looks OK, and then launches the script (or quits)
(For experts, it can still take the original case where all 7 parameters are passed at the command line)
There may still be some minor bugs, so for now we don't replace the original one until Alvaro can check
06:09 Stats - attachment 11
XY implant profiles -- attachment 12
06:30 DTAS 018; AIDA R2_80; BigRIPS 2009
Things getting a bit noisier?
Merger - attachment 13
TapeServer - attachment 14
Stats - attachment 15
The FEEs corresponding to DSSSD1 are all showing factors 2 to 10 higher than just 30 min. ago
F11 rates still near 180 cps, primary beam still around 130 pnA.
06:43 Before I can diagnose the high noise problem in DSSSD1, it goes back to normal
Merger - attachment 16
TapeServer - attachment 17
Stats - attachment 18
Maybe the issue was from looking at the details too often :)
07:46 Shift change.
DAQ continues running OK.
Statistics show noisy DSSD #1 (100-200kHz) - see attach 19
Tapeserver also shows higher than normal write to disk rate - see attach 20
After a few seconds write to disk rate goes back to normal - see attach 21
Data items rate looks OK (500k). This was checked after the rates in DSSD#1 went back to normal - see attach 22
FEE64 temperatures OK - see attach 23
Implants look OK - see attach 24
System-wide checks OK except nnaida7 fails ADC calibration as usual.
Reset Statistics
Stats now OK - see attach 25
Reset HEC implants
Timewarp events appear to be very frequent, consistently every 3-5 seconds.
This seems to have been happening ever since beam was put on target.
Analysed R2_94 using analyser in Desktop 3. No timewarps reported. See attach 26.
08:32 AIDA: R2_100,
DTAS: 21 ,
BigRips: 2010
08:41 Another noise spike from DSSD#1
Observed up to 1,600k data items per second - see attach 27
Write to disk ~10 MB/s as before.
See LEC xy plot - attach 28
HEC xy plot shows no hints of issues - see attach 29
Rate seems manageable - see attach 30 for analysis of noisy run R2_103.
Note few seconds deadtime in some FEE64 and unequal number of Pause/Resume in nnaida 22
09:45 Rate in DSSD#1 back to normal. Data rate 500k, Write to disk 5 Mb/s.
10:00 Started compressing R2_* files to save disk space.
Used nice gzip to compress to avoid conflicts with the DAQ.
Status of compression can be checked in ELOG desktop in the terminal window running ls -alth
10:32 DTAS and BigRIPS stop runs
AIDA on file R2_128
DTAS:24
BigRIPS 2011
10:56 Lost beam. BigRIPS and DTAS DAQs continue running. Accelerator operators advise beam should be back in 10 minutes.
11:12 Beam is back. BigRIPS & DTAS continue running and did not stop. AIDA file R2_133.
11:25 System-wide checks OK except nnaida7 fails ADC calibration as usual.
Stats OK, but nnaida19 is a bit more noisy than befor (80k) - see attach 31
Temperatures OK - see attach 32
TapeServer & Merger OK - see attach 33, 34 - rates have been low since 10 am
HEC xy plot OK - see attach 35
Reset online spectra
Leakage current OK - attach 36
|
|
775
|
Sun Nov 11 21:35:42 2018 |
CB, OH, CA, LS | Monday 12 November | 06:35 DAQ Continues ok
Stats ok - attachment 1
FEE Temps ok - attachment 2
Bias and leakage currents ok - attachment 3
System wide checks all ok
Chiller refilled
07:57 DAQ continues OK
Stats OK - attachment 4
FEE temperatures OK - attachment 5
Bias and leakage currents OK - attachment 6
System-wide checks OK *except* nnaida7 fails ADC calibration
10:06 DAQ continues OK
Stats OK - attachment 7
FEE temperatures OK - attachment 8
Bias and leakage currents OK - attachment 9
System-wide checks OK *except* nnaida7 fails ADC calibration
Workstation occasionally feels sluggish. See iostat 5 (attach 10) & top -a (attach 11)
12:08 DAQ continues OK
Stats OK - attachment 12
FEE temperatures OK - attachment 13
Bias and leakage currents OK - attachment 14
System-wide checks OK *except* nnaida7 fails ADC calibration
15:40 DAQ continues OK
Stats OK - attachment 15
FEE temperatures OK - attachment 16
Bias and leakage currents OK - attachment 17
System-wide checks OK *except* nnaida7 fails ADC calibration
16:58 DAQ continues OK
Stats OK - attachment 18
FEE temperatures OK - attachment 19
Bias and leakage currents OK - attachment 20
System-wide checks OK *except* nnaida7 fails ADC calibration |
|
579
|
Sat May 20 02:39:06 2017 |
CB, OH | Saturday 20 May | 10.35 DAQ continues OK
Current file May2017/R16
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases; leakage currents OK - see attachment 1
FEE64 Temperatures OK - see attachment 2
good events; statistics OK - see attachment 3
No warnings/errors reported by merger since DAQ GO - see attachment 4
*all* system wide checks OK *except* ADC calibration of nnaida7
10.45 E17/F11 ambient temperature +24.8 deg C, RH 39.9%, d.p. +10.0 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 50%)
11.00 DAQ stops OK
Current file May2017/R16
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
11.10 DAQ starts
File May2017/R17
16.30 DAQ continues OK
Current file May2017/R17
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases; leakage currents OK - see attachment 5
FEE64 Temperatures OK - see attachment 6
good events; statistics OK - see attachment 7
No warnings/errors reported by merger since DAQ GO - see attachment 8
*all* system wide checks OK *except* ADC calibration of nnaida7
16.45 E17/F11 ambient temperature +24.3 deg C, RH 39.1%, d.p. +9.5 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 50%)
16.50 DAQ stops OK
Current file May2017/R17
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
16.54 DAQ starts
File May2017/R18
Attached Ras Pi system console log for USB0 |
|
614
|
Tue May 30 07:56:05 2017 |
CB, NN, OH, AE | Tuesday 30 May - evening shift | 16.00 Still no beam
Current run /RIBF127R1/R1_197
Found dropped channels on nnaida1, ASIC4 - see attach 1
Check ASIC control x2
No effects
17.08 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok
merger and tapeserver ok
still no beam
17.20 Beam is back
AIDA RIBF127R1/R1_216
DAQ start BRIKEN 16
DAQ start BigRIPS 1016
17.25 Almost all implants in DSSSD#6 - see attach 2
Beam stopped on AIDA run RIBF127R1/R1_217
Increasing degrader thickness.
17.30 New degrader: 11m Al plate
Zero'd all histograms
Deleted online SortSas
AIDA RIBF127R1/R1_21
DAQ start BRIKEN 17
DAQ start BigRIPS 1017
17.44 Most implants still in #5,6. Adjusted degrader: 14mm Al
Implants now in dets #4,5 preferentially.
Zero'd all histograms
Deleted online SortSas
AIDA RIBF127R1/R1_221
DAQ continues running in BRIKEN 17
DAQ start BigRIPS 1018
18.05 Beam lost on AIDA run RIBF127R1/R1_226
18.35 Beam is back
Zero'd all histograms
Deleted online SortSas
AIDA RIBF127R1/R1_233
DAQ start BRIKEN 18
DAQ start BigRIPS 1019
19:10 DSSD Rates from R1_239
*** DSSSD # 1 count: 164076 old count: 109857 dt: 1.02 s LEC rate: 53189.47 Hz
*** DSSSD # 2 count: 211989 old count: 140492 dt: 1.02 s LEC rate: 70139.39 Hz
*** DSSSD # 3 count: 76697 old count: 49676 dt: 1.02 s LEC rate: 26507.92 Hz
*** DSSSD # 4 count: 72050 old count: 47860 dt: 1.02 s LEC rate: 23730.67 Hz
*** DSSSD # 5 count: 27482 old count: 17785 dt: 1.02 s LEC rate: 9512.87 Hz
*** DSSSD # 6 count: 51983 old count: 34674 dt: 1.02 s LEC rate: 16980.33 Hz
*** DSSSD # 1 count: 37 old count: 21 dt: 1.02 s HEC rate: 15.70 Hz
*** DSSSD # 2 count: 89 old count: 59 dt: 1.02 s HEC rate: 29.43 Hz
*** DSSSD # 3 count: 124 old count: 83 dt: 1.02 s HEC rate: 40.22 Hz
*** DSSSD # 4 count: 104 old count: 66 dt: 1.02 s HEC rate: 37.28 Hz
*** DSSSD # 5 count: 75 old count: 47 dt: 1.02 s HEC rate: 27.47 Hz
*** DSSSD # 6 count: 45 old count: 33 dt: 1.02 s HEC rate: 11.77 Hz
19:23 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok see attachment 4
merger and tapeserver ok
current AIDA file R1_244
20:01 BigRIPS and BRIKEN stopping the run
AIDA RIBF127R1/R1_253
20:08 BigRIPS and BRIKEN start
DAQ start BRIKEN 19
DAQ start BigRIPS 1020
AIDA RIBF127R1/R1_254
20:19 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok see attachment 5
merger and tapeserver ok
current AIDA file R1_258
20.51 Beam and DAQ continue OK
HEC x vs. y look OK - see attach 6
21:03 BigRIPS and BRIKEN stopping the run
AIDA RIBF127R1/R1_268
21.05 Beam lost while changing runs
21.07 Beam is back.
DAQ start BRIKEN 20
DAQ start BigRIPS 1021
AIDA RIBF127R1/R1_270
22:01 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok
merger and tapeserver ok
current AIDA file R1_282
22:02 BigRIPS and BRIKEN stopping the run
AIDA RIBF127R1/R1_282
22:03 BigRIPS and BRIKEN start
DAQ start BRIKEN 21
DAQ start BigRIPS 1022
AIDA RIBF127R1/R1_283
23:02 BigRIPS and BRIKEN stopping the run
AIDA RIBF127R1/R1_296
23:04 BigRIPS and BRIKEN start
DAQ start BRIKEN 22
DAQ start BigRIPS 1023
AIDA RIBF127R1/R1_297
23:40 FEE's temperature normal
statistics normal
system wide checks ok
leakage current and bias ok see attchment 7
merger and tapeserver ok
current AIDA file R1_306 |
|
851
|
Mon Jun 17 16:01:27 2019 |
CB, CG, OH, TD | Tuesday 18 June 00:00 - 16:00 | 00:00 New day. The DAQ continues OK
Beam setting 2 for enhanced yield of Sn100
No degrader
Statistics OK - see attach 1
FEE64 temps OK - see attach 2
Merger & Tape server OK - see attach 3 & 4
Bias OK - see attach 5
All system-wide checks OK, except nnaida7 fails ADC calibration
00:19 AIDA R2_473
DTAS 82
BigRIPS 2036
01:50 FEE temps and bias/leakage currents OK
Data rate continues at ~620k items/s and ~5.1MB/s
ASIC check performed successfully
02:29 DTAS run 85
BigRIPS run 2037
AIDA ~1.5GB into R2_492
02:30 DTAS reset correlation scaler at start of R2_493
Confirmed by change in value in Correlation status & control @ aidas1 window.
02:36 DTAS run 86 started
BigRIPS run 2038
AIDA file R2_494
04:38 DTAS run 88 stopped. AIDA run R2_512.
DTAS run 89 started.
BigRIPS run 2039
AIDA run R2_512 (1.8GB)
Temps + bias/leakage currents still ok
Data rate still ~600k items/s and ~5MB/s
Individual Good data rates remain roughly constant (see attachment 6)
All system-wide checks passed, except nnaida7 fails ADC calibration
05:48 Stats and histograms zeroed
06:28 DTAS run 91 stopped. AIDA run R2_528 at the time.
DTAS run 92 started
BigRIPS run 2040
AIDA run R2_528
07:50 Made some basic observations with the first file merged after the setting change
Attachment 7 shows implant x:y plots for each DSSD
Attachment 8 show PID for second setting with 100Sn highlighted in red and 96Ag in magenta
08:21 PID per DSSD Attachment 9
Sn100 per DSSD attachment 10
Sn100 Velocity against DSSD 11
Sn100 Velocity against DSSD Energy attachment 12
08:29 DTAS and BigRIPS stop
AIDA on file R2_546
DTAS starts file 95
BigRIPS run 2041
AIDA on file R2_547
08:53 Stats ok - attachment 13
Temps ok - attachment 14
System wide checks ok
ASIC check ok
Bias and leakage still ok though DSSD3 continues to rise - attachment 15
Merger continues with data rate around 700k - attachment 16
09:43 With the new implantation profile depositing most of the Sn100 in DSSD2 but some in the 3rd the
plan is to put in place a 200 micron degrader to bring the deposition into the centre of detector
2
10:15 Overnight MIDAS analysis has been completed.
Spectra have been exported to: /homes/npg/spectra/specs-2019Jun18-10.14.36
MIDAS will be switched to online mode with the change in degrader setting
10.33 DAQ stop
AIDA file RIBF147/R2_566
OH/AA/SN add 0.3mm Al degrader to Pb wall immediately upstream of the (CH2)n shield
10.35 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C
Water level c. 50% M-H markers
Temperature +24.1 deg C dew point +9.7 deg C RH 39.8%
10.39 DTAS starts file 98
BigRIPS run 2042
AIDA on file R2_567
11:06 Implantation events for the 2nd setting with 0,3mm Al plate - attachments 17-19
FEE64 Rate spectra - attachment 20
FEE64 HitRate spectra - attachment 21
1.8.L spectra - see attachments 22-25
nnaida1 73 ch FWHM, nnaida3 77 ch FWHM - cf. 73 & 78 ch FWHM respectively 10.41 yesterday
1.8.H spectra - see attcahments 26-27
p+n FEE64s 1.8.W spectra 20us FSR - attachment 28
n+n FEE64s 1.8.W spectra 20us FSR - attachment 29
11.30 Check ASIC Control *all* FEE64s & ASICs
zero *all* histograms
zero DAQ stats
11.50 analysis of RIBF147/R2_576
deadtime *all* FEE64s <<1%
no timewarps
11.57 ADC data synchronised - attachment 30
per FEE64 ADC data / 20.48us - attachment 31
12:39 DTAS and BigRIPS stop runs
AIDA on file R2_585
DTAS file 101
BigRIPS run 2043
AIDA on File R2_585
13:23 System wide checks ok
14:38 DTAS and BigRIPS stop runs
AIDA on file R2_683
OH offline analysis of BigRIPS-implant correlations for previous 2h indicates >90% of 100Sn are
now in DSSSD#2 with small d=fraction remaining in DSSSD#3
100Sn setting, 0.3mm Al degrader
ASIC settings 2019Jun13-08.56.35
DSSSD#1 slow comparator 0xa -> 0x1d
DSSSD#2 slow comparator 0xa -> 0x8
DSSSD#3 slow comparator 0x8 -> 0xa
DAQ stats before & after chn age of slow comparator thresholds above - see attachments 33 & 34
before 11x <20k 21x <50k 24x <100k cf after 11x <20k 22x <50k 23x <100k
merger 664k items/s cf 560k data items/s
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range, variable min. c. 2.5Hz
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
15.03 DAQ start
AIDA file R2_606
DTAS file 104
BigRIPS run 2044
|
|
554
|
Thu Apr 13 15:08:31 2017 |
CB | Card test | I tested the FWHM of a BNC PB-5 pulser signal as a function of shaping time using the first produced ISOL FEE64 card in Daresbury Labs.
Find attached four representative spectra per ASIC taken with 8, 5 and 0.5 us shaping time values. Run times are different.
Also find attached a plot of the FWHM as a function of the shaping time for the first channel in each ASIC. There appears to be a maximum of the FWHM at around 4 us. This may indicate the main source of noise is external, and at ~4 us the band pass lets most of the noise in.
Unlike the FEE cards employed in RIKEN, this card is grounded to the metal base plate through the screws. In order to investigate the effect of this ground on the noise level of the ADCs in the card, the card was disconnected from the metal plate base. An additional layer of insuating material was placed between the base and the FEE64 card. Nylon screws rather than metal screws were employed to affix the card to the base, and the same tests as before were repeated. See plot below. Overall, the same trend is recovered but suprisingly the FWHM is larger than before for ASICs #1,2 and #3. ASIC #4 has a lower FWHM than before. The reason for the change is not obvious, and may need further investigation.
Carlo
BNC PB-5 parameters
Delay 250 ns
Rate 100 Hz
Polarity POS
Pulse Top TAIL
Amplitude 0.5 V
|
|
625
|
Fri Jun 2 16:02:37 2017 |
CB | Saturday 3 June 00:00-08:00 | 00:02 Noise in nnaida 1 and 2 appears to be reduced.
However, some channels in nnaida1, ASIC4 and nnaida2, ASIC 1 have been dropped. See attachment 1
00:05 Analysed RIBF127R1/R1_1314 - see attachment 2
No timewarps, SYNC100 OK, dead time negligible
No mismatches between dead time and idle time
00:07 Sorted RIBF127R1/R1_1314 - rates OK
*** DSSSD # 1 count: 35064 old count: 0 dt: 1.00 s LEC rate: 35055.03 Hz
*** DSSSD # 2 count: 49092 old count: 0 dt: 1.00 s LEC rate: 49079.44 Hz
*** DSSSD # 3 count: 16520 old count: 0 dt: 1.00 s LEC rate: 16515.77 Hz
*** DSSSD # 4 count: 14753 old count: 0 dt: 1.00 s LEC rate: 14749.23 Hz
*** DSSSD # 5 count: 7128 old count: 0 dt: 1.00 s LEC rate: 7126.18 Hz
*** DSSSD # 6 count: 13937 old count: 0 dt: 1.00 s LEC rate: 13933.43 Hz
*** DSSSD # 1 count: 19 old count: 0 dt: 1.00 s HEC rate: 19.00 Hz
*** DSSSD # 2 count: 36 old count: 0 dt: 1.00 s HEC rate: 35.99 Hz
*** DSSSD # 3 count: 44 old count: 0 dt: 1.00 s HEC rate: 43.99 Hz
*** DSSSD # 4 count: 39 old count: 0 dt: 1.00 s HEC rate: 38.99 Hz
*** DSSSD # 5 count: 17 old count: 0 dt: 1.00 s HEC rate: 17.00 Hz
*** DSSSD # 6 count: 2 old count: 0 dt: 1.00 s HEC rate: 2.00 Hz
Zero'd all histogram and SortSas
00:10 System console log ttyUSB7 (nnaida1) attached - 3
00:22 BigRIPS & BRIKEN stop runs
AIDA on file R1_1318
00:26 BigRIPS starts run 1103
BRIKEN starts run 92
AIDA on file R1_1319
Zero'd all SortSas
01:18 DAQ continues OK
FEE64 temperatures - OK
Good event statistics - OK
System wide checks - OK except clock status for nnaida1 (status=6), and ADC calibration for nnaida 1, 21
No new Merger error messages
HEC x vs y plot OK - attachment 4
01:26 BigRIPS & BRIKEN stop runs
AIDA on file R1_1333
01:30 BigRIPS starts run 1104
BRIKEN starts run 93
AIDA on file R1_1334
02:06 Finished compressing RIBF127R1/R1_6* and R1_7*
Beginning compression of RIBF127R1/R1_8* and R1_9*
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_aidas1-lv_root
50G 43G 3.9G 92% /
tmpfs 3.9G 1.1G 2.9G 27% /dev/shm
/dev/sda1 477M 77M 376M 17% /boot
/dev/mapper/vg_aidas1-lv_home
860G 580G 236G 72% /home
/dev/mapper/Data1-data10
7.7T 6.6T 824G 89% /data10
/dev/sdg2 7.3T 3.7T 3.7T 50% /ntfs
02:25 BigRIPS & BRIKEN stop runs
AIDA on file R1_1346
02:27 BigRIPS starts run 1105
BRIKEN starts run 94
AIDA on file R1_1347
02:31 DAQ continues OK
Sorted R1_1347. DSSSD rates are
*** data items: 1044352 ( 89746.26 Hz)
*** ADC events: 125937 ( 10822.38 Hz)
*** time warps: 0 ( 0.00 Hz)
*** DSSSD # 1 count: 36971 old count: 33324 dt: 1.11 s LEC rate: 33252.59 Hz
*** DSSSD # 2 count: 49630 old count: 45531 dt: 1.11 s LEC rate: 44638.40 Hz
*** DSSSD # 3 count: 16611 old count: 15180 dt: 1.11 s LEC rate: 14940.33 Hz
*** DSSSD # 4 count: 16456 old count: 15001 dt: 1.11 s LEC rate: 14800.92 Hz
*** DSSSD # 5 count: 7463 old count: 6781 dt: 1.11 s LEC rate: 6712.40 Hz
*** DSSSD # 6 count: 15199 old count: 13737 dt: 1.11 s LEC rate: 13670.34 Hz
*** DSSSD # 1 count: 23 old count: 19 dt: 1.11 s HEC rate: 20.69 Hz
*** DSSSD # 2 count: 53 old count: 45 dt: 1.11 s HEC rate: 47.67 Hz
*** DSSSD # 3 count: 45 old count: 43 dt: 1.11 s HEC rate: 40.47 Hz
*** DSSSD # 4 count: 41 old count: 36 dt: 1.11 s HEC rate: 36.88 Hz
*** DSSSD # 5 count: 20 old count: 18 dt: 1.11 s HEC rate: 17.99 Hz
*** DSSSD # 6 count: 3 old count: 1 dt: 1.11 s HEC rate: 2.70 Hz
HEC x vs y plot OK - cleared SortSas
02:40 Leakage currents OK - attachment 5
FEE64 temperatures OK - attachment 6
Good events statistics OK - attachment 7
No new merger errors - attachment 8
03:28 Analysed RIBF127R1/R1_1359 - see attachment 9
No timewarps, SYNC100 OK
Dead time OK
03:29 BigRIPS & BRIKEN stop runs
AIDA on file R1_1360
03:31 BigRIPS starts run 1106
BRIKEN starts run 95
AIDA on file R1_1361
03:48 HEC x vs y plot OK. Cleared SortSas.
04:04 DAQ continues OK
All system-wide checks OK, *except* nnaida1 clock status (=6) and nnaida1, 21 ADC time calibration
04:30 BigRIPS & BRIKEN stop runs
AIDA on file R1_1374
04:32 BigRIPS starts run 1107
BRIKEN starts run 96
AIDA on file R1_1375
04:34 Sorted R1_1375. DSSSD rates are as follows
*** data items: 1101465 ( 93446.58 Hz)
*** ADC events: 125547 ( 10651.21 Hz)
*** time warps: 0 ( 0.00 Hz)
*** DSSSD # 1 count: 44101 old count: 39716 dt: 1.12 s LEC rate: 39211.50 Hz
*** DSSSD # 2 count: 64123 old count: 57044 dt: 1.12 s LEC rate: 57013.65 Hz
*** DSSSD # 3 count: 18735 old count: 16851 dt: 1.12 s LEC rate: 16657.84 Hz
*** DSSSD # 4 count: 18739 old count: 16870 dt: 1.12 s LEC rate: 16661.40 Hz
*** DSSSD # 5 count: 7490 old count: 6811 dt: 1.12 s LEC rate: 6659.58 Hz
*** DSSSD # 6 count: 15970 old count: 14515 dt: 1.12 s LEC rate: 14199.40 Hz
*** DSSSD # 1 count: 26 old count: 24 dt: 1.12 s HEC rate: 23.12 Hz
*** DSSSD # 2 count: 43 old count: 39 dt: 1.12 s HEC rate: 38.23 Hz
*** DSSSD # 3 count: 50 old count: 46 dt: 1.12 s HEC rate: 44.46 Hz
*** DSSSD # 4 count: 40 old count: 36 dt: 1.12 s HEC rate: 35.57 Hz
*** DSSSD # 5 count: 17 old count: 16 dt: 1.12 s HEC rate: 15.12 Hz
*** DSSSD # 6 count: 7 old count: 6 dt: 1.12 s HEC rate: 6.22 Hz
04:36 Leakage currents OK - attachment 10
FEE64 temperatures OK - attachment 11
Good events statistics OK - attachment 12
No new merger errors - attachment 13
05:09 DAQ continues OK. Analysed RIBF127R1/R1_1383 - see attachment 14
No timewarps, SYNC100 OK
Dead time OK
Hit pattern OK - see attachment 15
05:28 Beam lost. BRIKEN & BigRIPS stopping run.
AIDA on run RIBF127R1/R1_1387
05:31 Beam is back. Issue unclear.
BigRIPS starts run 1108
BRIKEN starts run 97
AIDA on run R1_1388
05:37 Lost beam again. It appears to be an issue with "power"
AIDA on run RIBF127R1/R1_1389
BRIKEN & BigRIPS still running.
05:39 BigRIPS no longer sending signal: lost synchronisation.
05:43 Beam is back. Synchronisation is back.
BRIKEN & BigRIPS stopping run.
05:47 BigRIPS starts run 1109
BRIKEN starts run 98
AIDA on run R1_1391
05:53 Analysed R1_1391 - see attachment 16
No timewarps, SYNC100 OK
Dead time OK
DAQ continues OK
06:05 Sorted R1_1395. DSSSD rates as follows
*** data items: 1158578 ( 105681.80 Hz)
*** ADC events: 120781 ( 11017.26 Hz)
*** time warps: 0 ( 0.00 Hz)
*** DSSSD # 1 count: 54590 old count: 48655 dt: 1.12 s LEC rate: 48746.42 Hz
*** DSSSD # 2 count: 79085 old count: 70259 dt: 1.12 s LEC rate: 70619.36 Hz
*** DSSSD # 3 count: 24651 old count: 21385 dt: 1.12 s LEC rate: 22012.24 Hz
*** DSSSD # 4 count: 20753 old count: 18595 dt: 1.12 s LEC rate: 18531.50 Hz
*** DSSSD # 5 count: 8376 old count: 7452 dt: 1.12 s LEC rate: 7479.39 Hz
*** DSSSD # 6 count: 17321 old count: 15715 dt: 1.12 s LEC rate: 15466.88 Hz
*** DSSSD # 1 count: 27 old count: 24 dt: 1.12 s HEC rate: 24.11 Hz
*** DSSSD # 2 count: 43 old count: 38 dt: 1.12 s HEC rate: 38.40 Hz
*** DSSSD # 3 count: 41 old count: 35 dt: 1.12 s HEC rate: 36.61 Hz
*** DSSSD # 4 count: 38 old count: 33 dt: 1.12 s HEC rate: 33.93 Hz
*** DSSSD # 5 count: 14 old count: 14 dt: 1.12 s HEC rate: 12.50 Hz
*** DSSSD # 6 count: 1 old count: 1 dt: 1.12 s HEC rate: 0.89 Hz
06:19 Leakage currents OK - attachment 17
FEE64 temperatures OK - attachment 18
Good events statistics OK - attachment 19
No new merger errors - attachment 20
06:23 HEC x vs y plot OK - attachment 21
Zero'd all SortSas
06:27 Lost the beam. AIDA on run R1_1401.
Same "power-related" issue as before. Expected 2-3 minutes shutdown.
Lost synchronisation.
06:32 Beam is back. Synchronisation is back.
BRIKEN & BigRIPS stopping run.
06:33 BigRIPS starts run 1110
BRIKEN starts run 99
AIDA on run R1_1402
06:58 DAQ continues OK
HEC x vs y plot OK - attachment 22
Zero'd all SortSas
Analysed R1_1407 - attachment 23
No timewarps, SYNC100 OK
Dead time OK
07:06 Sorted R1_1407. Pulser events are still synchronised - attachment 24
07:30 BRIKEN & BigRIPS stopping run.
AIDA on run R1_1415
07:33 BigRIPS starts run 1111
BRIKEN starts run 100
AIDA on run R1_1416
07:35 Leakage currents OK - attachment 25
FEE64 temperatures OK - attachment 26
Good events statistics OK - attachment 27
No new merger errors - attachment 28
HEC x vs y plot OK
Zero'd SortSas |
|
699
|
Fri Nov 17 03:32:31 2017 |
CB | Julabo FL11006 recirculating chiller refilled | 12:32 Chiller found almost empty & still working at 20C. Refilled to overflow. |
|
854
|
Tue Jun 18 23:58:46 2019 |
CB | Wed Jun 19 8:00-16:00 | 08:00 Shift change
No change in settings
DAQ continues running OK
Good events rate OK - see attach 1
FEE64 temperature OK - see attach 2
Merger & Tape server OK - see 3 & 4
Leakage currents OK - see attach 5
Online HEC xy plot OK, most implants in DSSD2 - see attach 6
Zeroed online histograms
09:29 DTAS DAQ stops on run 135
AIDA on run R2_787
09:32 DTAS DAQ restarts on run 136
AIDA on run R2_787
BigRIPS on run 2053
09:33 DAQ continues OK
Good events rate OK - see attach 7
Merger ~ 700k items/s
Tape ~ 5400 Kbytes/s
Leakage currents OK - see attach 8
Online HEC xy plot OK - see attach 9
10:31 Good event rate in nnaida 19, 24 steadily creeping up. See attach 10.
Currently 160k and 120k
Merger ~ 710 k items/s
Tape ~ 5689 kbytes/s
All system-wide checks OK, except nnaida7 fails ADC calibration as usual
11:20 Good event rate stable - see attach 11
FEE64 temperatures OK - see attach 12
Merger ~700k items/s
Tape server ~ 5500 Kbytes/s
Leakage currents OK - see attach 13 & 14
11:30 DTAS stops DAQ on run 139
BigRIPS on run 2053
AIDA on run R2_806
11:32 DTAS restarts on run 140
BigRIPS 2053
AIDA R2_807
13:14 DAQ continues OK
Good statistics events stable - see attach 15
Merger ~ 730k items/s
Tape server ~ 5500 KBytes/s
Leakage current OK - see attach 16
13:34 DTAS stops DAQ on AIDA R2_826
13:37 DTAS restarts DAQ on run 144
BigRIPS run 2055
AIDA run 827
15:10 DTAS DAQ reports 20% drop in F11 counting rate
AIDA plastic unchanged, beam current unchanged. Focusing issue?
Reset online histograms to check we are still implanting. We are.
Acquisition continues uninterrupted.
15:17 Good statistics OK - see attach 17
FEE64 temperature OK - see attach 18
Merger ~ 700k items/s
TapeServer ~ 5500 Kbytes/s
Detector leakage current OK - see attach 19
15:30 DTAS stops DAQ on AIDA run R2_845
15:33 DTAS restarts DAQ on run 147
BigRIPS run 2056
AIDA run R2_846
|
|
788
|
Thu Nov 15 22:55:38 2018 |
CA, TD, OH, LS | Friday 16th November 08.00 - 16.00 | 07.56 DAQ continues - AIDA file RIBF148/R5_822
165Pm BigRIPS setting + 2.8mm Al degrader
08.13 zeroed xy hit pattern on online analysis and MIDASsort
08.30 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 1)
good event statistics ok (attachment 2)
detector bias/leakage currents ok (attachment 3)
08.34 Merger and TapeServer ok, no error messages in terminal (attachments 4/5)
08.40 zeroed all spectra on online analysis and MIDASsort
08.44 BRIKEN and BigRIPS stop
AIDA file RIBF148/R5_830
08.45 BigRIPS starts run 1087
BRIKEN starts run 102
AIDA on file RIBF148/R5_830
09.13 n vs p multiplicity (attachment 6)
xy hit pattern (*deleted, took wrong screenshot, sorry! -CA@12.16*)
Energy X vs Energy Y plot (*deleted, took wrong screenshot, sorry! -CA@12.16*)
12.17 see elog entry for 15th November 2018 00.00-08.00 (attachments 9 and 10) for screenshots of the above before
degrader change
09.17 BRIKEN and BigRIPS stop
AIDA on file RIBF148/R5_836
beam stop to change Al degrader thickness to 3.3mm
09.23 chiller refilled while access available
humidity, temperature, dew point measurements obtained
09.25 detector bias/ leakage currents ok (attachment 7)
09.30 zeroed all spectra in online analysis and MIDASsort
09.31 beam back on
BRIKEN and BigRIPS start
AIDA file RIBF148/R5_838
BRIKEN run 103
BigRIPS run 1088
10.32 BRIKEN and BigRIPS stop
AIDA file RIBF148/R5_848
10.33 BRIKEN and BigRIPS start
AIDA file RIBF148/R5_848
BRIKEN run 104
BigRIPS run 1089
10.45 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 8)
good event statistics ok (attachment 10)
detector bias/leakage currents ok (attachment 9)
11.20 ran analyser on file R5_847 - attachment 11
no timewarps observed
dead time in nnaida19 at ~1s out of 355.283s (~0.3%)
rest at zero, except nnaida20 at ~0.6s and nnaida21 at ~0.1s
11.33 BRIKEN and BigRIPS stop
AIDA file RIBF148/R5_859
11.34 BRIKEN and BigRIPS start
AIDA file RIBF148/R5_859
BRIKEN run 105
BigRIPS run 1090
12.05 n vs p multiplicity (attachment 12)
xy hit pattern (attachment 13)
Energy X vs Energy Y plot (attachment 14)
this is after change of Al degrader thickness to 3.3mm
12.36 BRIKEN and BigRIPS stop
AIDA file RIBF148/R5_869
12.36 BRIKEN and BigRIPS start
AIDA file RIBF148/R5_869
BRIKEN run 106
BigRIPS run 1091
12.40 online histograms
per FEE64 Rate - attachment 15
per FEE64 HitRate - attachment 16
1.8.L spectra - attachments 17-20
nnaida1 pulser peak width 70ch FWHM
1.8.H spectra - attachments 21-22
1.8.W spectra - attachments 23-24
12.47 beam off
AIDA file RIBF148/R5_870
12.54 BRIKEN and BigRIPS stop
AIDA file RIBF148/R5_871
13.10 MIDASsort analysis RIBF148/R5_871 - all ADC data synchronised - attachments 25-26
13.16 correlation analysis decay plots for each detector with the Al degrader thickness at 3.3mm (attachment 23)
see elog entry November 15th 2018 00:00-08:00 (attachments 16-18) for same plots with previous degrader
thickness.
13.26 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 24)
good event statistics ok (attachment 25)
detector bias/leakage currents ok (attachment 26)
15.04 see other elog entries for correlation analysis and high energy Ex vs Ey plots compared between different Al
degrader thicknesses.
15.38 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 28)
good event statistics ok (attachment 27)
detector bias/leakage currents ok (attachment 29)
15.55 BRIKEN start background measurement
BRIKEN not writing to file
AIDA file RIBF148/R5_896
Online histograms available
16.00 BRIKEN start writing to file
AIDA file RIBF/R5_897
BRIKEN run 107
17.18 DAQ stop AIDA file RIBF148/R5_907
End of run RIBF148 due to accelerator problems requiring ~3-4 days to fix
'low' mass BigRIPS setting postponed
ASIC check load
all onine histograms zero'd
17.22 DAQ start AIDA file RIBF148/R6
Pulser walkthrough
BNC PB-4 amplitudes 90,000 - 10,000 @ 10,000 step
x5 attenuator IN
Frequency 25Hz range
Delay MIN
Polarity -
Tail pulse
17.37 DAQ trop AIDA file RIBF148/R6_2
1.8.L spectra - see attachments 30 & 31
17.40 DAQ start AIDA file RIBF148/R7
Pulser walkthrough
BNC PB-4 amplitudes 1,200 - 1,000 @ 1,000 step
x5 attenuator IN
Frequency 25Hz range
Delay MIN
Polarity -
Tail pulse
17.50 DAQ stop AIDA file RIBF148/R7_1
1.8.L spectra - see attachments 32 & 33
17.54 DAQ start AIDA file RIBF148/R8
background
BNC PB-4 pulser OFF
18.00 detector biases & leakage currents OK - see attachments 34 & 35
FEE64 temperatures OK - see attachment 36
good event statistics OK - see attachments 37
Merger OK - see attachment 38
TapeServer OK - see attachment 39
no error or warning messages terminal server sesssions reported
per FEE64 Rate spectra - attachment 40
1.8.W spectra 20ms FSR - attachments 41 & 42
18.10 DAQ stop AIDA file RIBF148/R8_2
Detector bias OFF
FEE64 power OFF
18.12 Ambient temperature +25.5 deg C, d.p. +2.2 deg C, RH 21.5%
18.15 Withdraw AIDA from BRIKEN - done
2x NIM bin OFF
1x NIM bin fan tray OFF
1x USB ac mains relay OFF
Julabo FL11006 chiller OFF front panel/rear panel/wall-mounted 3ph outlet
2x network cables disconnected and coiled/cable-tied to stairwell railings
disconnect coorelation scaler trigger & reset inputs to root MACB front panel
disconnect 50MHz TTL clock root MACB rear panel
disconnect AIDA plastic veto
discopnnect 2x ac mains cabnles from ac mains distribution box
remove AIDA support assembly nose support
19.00 raise AIDA support assembly feet/lower AIDA support assembly wheels from/to F11 floor
|
|
780
|
Tue Nov 13 07:35:37 2018 |
CA, TD, OH | Tuesday 13 November 16:00 - 00:00 | 16.36 DAQ continues ok
AIDA file RIBF148/R5_198
BRIKEN file 37
BigRIPS file 1022
16.38 system wide checks ok, except nnaida7 ADC calibration failure
16.40 FEE64 temperatures ok (attachment 1)
16.42 good event statistics ok (attachment 2)
16.43 detector bias/leakage currents ok (attachment 3)
16.44 Merger and TapeServer ok, no error messages in terminals (attachments 4 and 5)
16.51 BRIKEN stop
AIDA file RIBF148/R5_200
17.00 Al Degrader thickness changed from 2.3mm to 2.8mm
The 2.3mm plate was previously assumed to be 2.5mm, but this has been corrected by measuring individual Al
plates with digital micrometer.
17.02 BRIKEN start
BRIKEN file 38
BigRIPS file 1023
AIDA file RIBF148/R5_202
18.01 BRIKEN stop
AIDA file RIBF148/R5_211
18.03 BRIKEN start
AIDA file RIBF148/R5_212
BRIKEN file 39
BigRIPS file 1024
18.08 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 6)
good event statistics ok (attachment 8)
detector bias/leakage currents ok (attachment 7)
18.11 Merger and TapeServer ok, no error messages in terminal
19.00 BRIKEN stop
AIDA file RIBF148/R5_221
19.02 BRIKEN start
AIDA file RIBF148/R5_221
BRIKEN file 40
BigRIPS file 1025
19.57 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 9)
good event statistics ok (attachment 10)
detector bias/leakage current ok (attachment 11)
20.01 BRIKEN stop
AIDA file RIBF148/R5_231
20.03 BRIKEN start
AIDA file RIBF148/R5_231
BRIKEN file 41
BigRIPS file 1026
21.01 BRIKEN stop
AIDA file RIBF148/R5_240
21.03 BRIKEN start
AIDA file RIBF148/R5_240
BRIKEN file 42
BigRIPS file 1027
21:18 system wide checks ok - except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 12)
good event statistics ok (attachment 13)
detector bias/leakage current ok (attachment 14)
22:01 BRIKEN stop
AIDA file RIBF148/R5_250
22:03 BRIKEN start
AIDA file RIBF148/R5_250
BRIKEN file 43
BigRIPS file 1028
22:10 system wide checks ok - except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 15)
good event statistics ok (attachment 16)
detector bias/leakage current ok (attachment 17)
Merger and TapeServer ok, no error messages in terminal
23:01 BRIKEN stop
AIDA file RIBF148/R5_260
23:03 BRIKEN start
AIDA file RIBF148/R5_260
BRIKEN file 44
BigRIPS file 1029
23.05 system wide checks ok - except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 18)
good event statistics ok (attachment 20)
detector bias/leakage current ok (attachment 19)
Merger and TapeServer ok, no error messages in terminal
|
|
789
|
Fri Nov 16 04:47:39 2018 |
CA, TD, OH | Correlation analysis at different degrader Al thickness | 13.53 Correlation analysis plot of all detectors with 3.3mm Al degrader thickness (attachment 1)
13.54 Correlation analysis plot of detectors 1 and 2 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 2)
Correlation analysis plot of detectors 3 and 4 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 3)
Correlation analysis plot of detectors 5 and 6 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 4)
14.02 Plots made over first 200ms of data |
|
795
|
Mon May 13 03:23:58 2019 |
CA, TD, OH | Monday 13 May |
09.55 all system wide checks OK *except* nnaida7 fails ADC calibration
FEE64 temperatures OK - see attachment 1
good event statistics OK - see attachment 2
all FEE64s <100k, 11x < 20k
1.8.L spectra - see attachments 3 & 4
nnaida1 70ch FWHM, nnaida3 80 ch FWHM
detector biases & leakage currents OK - see attachments 5 & 6
1.8.W spectra 20us FSR - see attachments 7 & 8
nnaida1 Options, Local Controls, Data Redaout, Discriminator Controls - see attachment 9-13
Lost Activity Monitor -see attachment 14
18.01 DAQ found stopped
This was caused by a chnage to the AIDA external clock frequency - see https://elog.ph.ed.ac.uk/AIDA/798
Following change of AIDA external clock frequency to 50MHz
DAQ RESET
DAQ SETUP
Sync all ASIC clocks using Resync
all system wide checks OK *except* nnaida7 fails ADC calibration
zero all histograms
DAQ GO
18.31 FEE64 temperatures OK - see attachment 15
good event statistics OK - see attachment 16
all FEE64s <100k, 10x < 20k
detector biases & leakage currents OK - see attachments 17 & 18 |
|