 Sun Jun 16 00:52:27 2019, Ela, Sonja, Victor, root file 6:30-8:30 
|
| |
|
Sun Jun 16 03:42:17 2019, Ela, Sonja, Victor, root file 8:30-10:30
|
| |
|
Sun Jun 16 04:44:05 2019, Ela, Sonja, Victor, root file 10:30-12:30
|
| The beam stopped a couple of times due to problems before RRC |
|
Sun Jun 16 06:55:31 2019, Ela, Sonja, Victor, root file 12:30-14:30
|
| |
|
Fri Jun 7 01:55:24 2019, CA, JA , AT, merger test
|
Setup: On 17th-May (11:18 - 11:38), AIDA was inside DTAS. Measurement of 60Co source.
Files:
|
|
Thu Jun 6 09:36:52 2019, Alvaro, Jorge, Ale, new config file
|
New config file: 20190606_Conf.xlsx
Changed with respect to the earlier file (20190605_Conf.xlsx):
|
|
Wed Jun 19 05:10:15 2019, Alvaro, Aida plastic - gain change
|
TAC AIDAPL - CryA changed
After increasing the gain, x2 peaks in TAC |
|
Wed May 15 11:53:17 2019, Algora, Nacher, Kiss, Background
|
Start: 20:05
Stop: 09:44
Background rate 2.9 kHz (Dynodes), 2.3 (Anodes) (Threshold of detector 13 was increased) |
|
Wed May 15 11:50:04 2019, Algora, Nacher, 137Cs listmode, and rootfile
|
137Cs source in the center of the DTAS, with the IFIC holder
list mode files: Cs137_Source_20190515_000.dlt to Cs137_Source_20190515_005.dlt
Root file: 201905151942_137Cs.root |
|
Wed May 15 06:40:16 2019, Algora, Kiss, Nacher , DTAS aligned and calibrated
|
Signal cables (long cables, from preamp to digitizer) of channels 13 and 16 were changed. For the moment they have not been relabelled.
We assumed that it was not a HV supply or cable problem, since the anods were aligned and only the dynodes moved.
After changing the cables we realigned the dynodes and recalibrated all signals. Screen shots are attached. |
|
Thu May 16 02:02:24 2019, Algora Kiss Nacher, detector 3 moved over night
|
After the long background measurement we have measured 60Co to check alignment.
Everything looks fine except for detector #3 that has moved to lower gain (seen in dynodes and anodes).
See figures attached. |
|
Thu May 16 06:59:51 2019, Algora Kiss Nacher, Det 3
|
Det 3 moved, both Anode and Dynode. So we have changed the HV cable to test if there are no more jumps. We used cable 9 and it was not
relabeled. The HV of the detector was corrected. It was changed to 527.5 V |
|
Mon Jun 10 04:14:39 2019, Ale, Jose, Background measurement overnight
|
Start:~14:00 (June 9)
Stop:10:30
|
|
Mon Jun 10 04:18:24 2019, Ale, Jose, New Configuration File
|
File: 20190610_1145_Conf_DTAS.xlsx
Several changes and corrections
|
|
Mon Jun 10 08:07:17 2019, Ale, Jose, Test of pulser count rates
|
File: 20190610_1602_background_AIDA_in.root
SyncPulse: 61777
|
|
Mon Jun 10 10:44:36 2019, Ale, Jose, New Conf file with new calibration
|
| File: 20190610_1835_Conf_DTAS.xlsx |
|
Mon Jun 10 12:31:52 2019, Ale, Jose, New calibration
|
New calibration with more statistics
File: 20190610_2030_60Co_137Cs_AIDA_in.root
|
|
Mon Jun 10 12:48:01 2019, Ale, Jose, New Config file 6x
|
Conf file with new calibration:
20190610_2035_Conf_DTAS.xlsx
|
|
Fri Jun 14 16:22:25 2019, AT, OH, JA, CG, TD, AIDA Sync
|
Problem with the sync checker appeared AIDA was not its notmal 14us out from DTAS.
Check with source shows we are in sync still
|
|
Wed Jun 12 02:04:07 2019, AA, EN, PM, AT, background during in-beam exp.
|
In-beam experiment going on. Only 12h of beam in the last 21h.
Start: ~1pm (11th-June)
|