| ID |
Date |
Author |
Subject |
|
675
|
Thu Oct 19 01:40:35 2017 |
TD, OH | Thursday 19 October |
09.40 DAQ continues OK
File /TapeData/Oct17/R1_280
BNC PB-4 Pulser frequency switched from 250Hz to 25Hz range
09:54 ASIC Temperatures - Attachment 1
Bias and leakage currents ok - Attachments 2 & 3
Statistics - Attachment 4
10:19 Output of analysis of R1_291 - Attachment 5
11:02 Pulser widths measured before changing jumpers (In log book)
DAQ stopped on Run R1_304
11:31 All field plane jumpers removed (Jumpers 1&3)
System wide checks ok
ASIC load check ok
11:37 DAQ started online only
Statistics - Attachment 6
FEE temperatures - Attachment 7
11:46 Layout 1 - Attachments 8 & 9
Layout 2 - attachments 10
13:38 Layouts 3 - Attachment 11
Layout 4 - Attachment 12
Pulser widths measured using 1.8.L spectra.
Most channels show an increase in noise with the FWHM increased by ~5-10 channels
(Recorded in log book)
13:55 Layout 7 p-side waveforms - Attachments 13 & 14
Layout 8 n-side waveforms - Attachments 15 & 16
For comparison with jumpers on see yesterday's elog entry: https://elog.ph.ed.ac.uk/AIDA/674
14:02 DAQ stopped
14:23 PCB ground plane jumper removed from all adapter boards (Jumper 2)
Bias and leakage currents ok T = 23.0 DP = +8.8 H = 38.7% - Attachment 17
System wide checks all ok
ASIC load check ok
DAQ Started
14:44 FEE temperatures all ok - Attachment 18
Statistics - Attachment 19
14:54 Layout 1 - Attachment 20 & 21
Layout 2 - Attachment 22
15:17 Layout 3 p-side pulser - Attachment 23
Layout 4 n-side pulser - Attachment 24
Pulser widths measured using 1.8.L spectra
In comparison with just having the FP jumpers removed for channels that were not noisy before they show no
to only minor increases in noise.
However channels that were previously noisy with all jumpers on show drastic increases in the amount of
noise. Increases in the FWHM of up to 80ch
13:55 Layout 7 p-side waveforms - Attachments 25 & 26
Layout 8 n-side waveforms - Attachments 27 & 28
DAQ Stopped
16:15 Detector bias turned off as replacing the jumpers is challenging
16:55 All jumpers back on. I advise starting with all on the new boards tomorrow and removing if needed.
Pain to put back on when mounted with cables.
16:59 System wide checks ok
Bias back on and leakage currents ok - Attachment 29
17:09 Statistics - Attachment 30
FEE temperatures - Attachment 31
By putting the jumpers back the statistics appear to have recovered to a similar level to this morning
17:25 FEEs powered down to do a power cycle for Patrick
17:50 FEEs powered up
18:00 Same javascript errors as yesterday when setting up DAQ
System wide checks all ok
FEE Temperatures ok
18:06 DAQ started
Statistics similar to before power cycle - Attachment 32
Layout 1 looks good - Attachments 33 & 34
18:14 DAQ stopped
18:16 DAQ Started
Writing to R2 in /TapeData/Oct17/
Writing at 11Mb/s
18:56 Statistics - Attachment 35 |
|
676
|
Thu Oct 19 11:32:29 2017 |
TD, OH | Thursday 19 October | >
> 09.40 DAQ continues OK
> File /TapeData/Oct17/R1_280
>
> BNC PB-4 Pulser frequency switched from 250Hz to 25Hz range
>
> 09:54 ASIC Temperatures - Attachment 1
> Bias and leakage currents ok - Attachments 2 & 3
> Statistics - Attachment 4
>
> 10:19 Output of analysis of R1_291 - Attachment 5
>
> 11:02 Pulser widths measured before changing jumpers (In log book)
> DAQ stopped on Run R1_304
>
> 11:31 All field plane jumpers removed (Jumpers 1&3)
> System wide checks ok
> ASIC load check ok
>
> 11:37 DAQ started online only
> Statistics - Attachment 6
> FEE temperatures - Attachment 7
>
> 11:46 Layout 1 - Attachments 8 & 9
> Layout 2 - attachments 10
>
> 13:38 Layouts 3 - Attachment 11
> Layout 4 - Attachment 12
> Pulser widths measured using 1.8.L spectra.
> Most channels show an increase in noise with the FWHM increased by ~5-10 channels
> (Recorded in log book)
>
> 13:55 Layout 7 p-side waveforms - Attachments 13 & 14
> Layout 8 n-side waveforms - Attachments 15 & 16
> For comparison with jumpers on see yesterday's elog entry: https://elog.ph.ed.ac.uk/AIDA/674
>
> 14:02 DAQ stopped
>
> 14:23 PCB ground plane jumper removed from all adapter boards (Jumper 2)
>
> Bias and leakage currents ok T = 23.0 DP = +8.8 H = 38.7% - Attachment 17
> System wide checks all ok
> ASIC load check ok
>
> DAQ Started
>
> 14:44 FEE temperatures all ok - Attachment 18
> Statistics - Attachment 19
>
> 14:54 Layout 1 - Attachment 20 & 21
> Layout 2 - Attachment 22
>
> 15:17 Layout 3 p-side pulser - Attachment 23
> Layout 4 n-side pulser - Attachment 24
>
> Pulser widths measured using 1.8.L spectra
>
> In comparison with just having the FP jumpers removed for channels that were not noisy before they show no
> to only minor increases in noise.
>
> However channels that were previously noisy with all jumpers on show drastic increases in the amount of
> noise. Increases in the FWHM of up to 80ch
>
> 13:55 Layout 7 p-side waveforms - Attachments 25 & 26
> Layout 8 n-side waveforms - Attachments 27 & 28
>
> DAQ Stopped
>
> 16:15 Detector bias turned off as replacing the jumpers is challenging
>
> 16:55 All jumpers back on. I advise starting with all on the new boards tomorrow and removing if needed.
> Pain to put back on when mounted with cables.
>
> 16:59 System wide checks ok
> Bias back on and leakage currents ok - Attachment 29
>
> 17:09 Statistics - Attachment 30
> FEE temperatures - Attachment 31
>
> By putting the jumpers back the statistics appear to have recovered to a similar level to this morning
>
> 17:25 FEEs powered down to do a power cycle for Patrick
>
> 17:50 FEEs powered up
>
> 18:00 Same javascript errors as yesterday when setting up DAQ
> System wide checks all ok
> FEE Temperatures ok
>
> 18:06 DAQ started
> Statistics similar to before power cycle - Attachment 32
> Layout 1 looks good - Attachments 33 & 34
>
> 18:14 DAQ stopped
>
> 18:16 DAQ Started
> Writing to R2 in /TapeData/Oct17/
> Writing at 11Mb/s
>
> 18:56 Statistics - Attachment 35
Please could you repeat the power cycle and this time turn all the FEE64s at once. The error I am looking to solve occurs ( so it is believed ) when all 24 request access to the server together. |
|
910
|
Thu Oct 19 10:39:20 2023 |
NH | Thursday 19 October | Water Temp: 20 C - Flow felt on pipe
AIDA interlock OVERRIDE
One USB Hub for the FEE64 TTYs was unplugged on cable tray, replugged in
(may fix Pi_Monitor)
Bias DSSD (Ch 3)
Leakage current stays at 17 uA during ramp up. At 150 V it quickly drops back to 6 uA
Fig 1
Current FEE mapping
p+n aida09 aida01 aida10
aida11 aida03 aida12
n+n aida02 aida04
Unused aida06 aida08
Due to merger need 8 FEEs 1-8 to merge properly will temporarily renumber for 1 DSSSD test
- Will revert to this numbering for experiment!
Power up with unchanged configuration to test
Fee Temps OK Figure 2
Start DAQ at 0x64 threshold (1 MeV)
Most channels 0 rate (expected)
ASIC01 of AIDA4 very hot
2 channels in aida10 very hot
Figure 3
Pulser OFF and only connected to aida11 aida03 aida12
LOCAL operation at present 10V/10X level, positive tail, 25 Hz
STOP and Power off to renumber
New mapping for now:
p+n aida05 aida01 aida06
aida07 aida03 aida08
n+n aida02 aida04
aida09 ---> aida05
aida10 ---> aida06
aida11 ---> aida07
aida12 ---> aida08
-
Backup dhcpd.conf -> dhcpd.conf231019
Update to only first 8 fees
only turn on Relay 1
Update MIDAS Tcl
/MIDAS/config/TclHttpd/aidas-gsi@8015/startup.Tcl
list aida01... aida08
new folder
/home/npg/LayOut/GSI_triple_test_renumber
copy to /tmp
-
Reboot MIDAS and Power on Relay 1
Power OFF
Reboot dhcp!
Anydesk Connection Lost??
Make new DB key 2023Oct19-13.46.30
Copy aida01/CONTENTS (p+n) to aida06 and aida08
Cannot update Options http://localhost:8015/AIDA/Options/Options.tml ? Error 500
Figure 4
Load settings manually and check-load ASIC
TODO: Manually change files, or?
GO
ADC items + rates figures 5, 6
Restart Merger
xfer Links (bad)
Netvar -> Inquire Registers
NetVar.MERGE.RunOptions WRITE 1
Merger now shows xfer Links => Merger
Merger GO
Open file BG18OCT23 R1
STOP DAQ
Data Xfer #1 Enable
GO DAQ
See merger links all GSI_triple_test_renumber
Enable output to data storage
xfer Links => Merger => storage
See tape rate: 3 MB/s (!)
Also start MBS on x86l-119 (new AIDA FDR) and try MBS relay
rate seen in MBS
Figure 8 - Accumulated statistics for ca 3 hours
Figs 9, 10 - ADC spectra
System turned off and DSSSD biased down for end of work day, due to water issue |
|
571
|
Thu May 18 02:16:05 2017 |
CB, TD, OH | Thursday 18 May | 10.10 DAQ continues OK
Current file May2017/R10_346
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
'good events' statistics OK - see attachment 4
No warnings/errors reported by merger since DAQ GO - see attachment 5
*all* system wide checks OK
10.20 E17/F11 ambient temperature +24.3 deg C, RH 39.0%, d.p. +9.3 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 65%)
10.25 DAQ stops OK
Current file May2017/R13_294
Files May2017/R13* *deleted*
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
10.30 DAQ starts
File May2017/R14
17.34 DAQ stops OK
Current file May2017/R14_113
Files May2017/R14* *deleted*
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control
Zero all spectra
*all* system wide checks OK
17.37 DAQ starts
File May2017/R15
Detector biases & leakage currents OK - see attachments 6 & 7
FEE64 Temperatures OK - see attachment 8
good events statistics - higher rates for several FEE64s - due to addition of system consoles? - see
attachment 9
No warnings/errors reported by merger since DAQ GO - ~ +30% data rate - see attachment 10 |
|
154
|
Thu Feb 18 10:23:48 2016 |
TD | Thursday 18 February | MSL type BB18(DS)-1000 serial 2998-22
Bias +200V, I_L +=6.200uA, ambient temperature +20.1 deg C
DSSSD - AIDA adaptor PCB cabling
4 off LH Coupler (Kapton PCB, 5cm), 2x 34-way Samtec ribbon cable (45cm), RH coupler(Kapton PCB, 10cm)
+ 3M 1245 1.4mil copper foil screen ribbon cables + RH coupler only (i.e. not LH coupler)
+ drain wires -> gold-plated Lemo-00 test input connectors
nnaida 11 & 12 AIDA adaptor PCB rev B
nnaida 13 & 14 AIDA adaptor PCB rev C (LK1 fitted)
ground links LK3 & LK7 fitted to nnaida11-14 AIDA adaptor PCBs
Heavy duty copper cable connects copper front end frames of FEE modules
Nitto 5011N conductive gasket between FEE module and front end frames
Standard ASIC settings
nnaida 11 & 12 - negative input
nnaida 13 & 14 - positive input
Pulser BNC PB-5
Fall time 1.0ms
Rate 100Hz
Delay 250ns
Ampl 5.00000V
Polarity +
Pulse top Tail
Atten 10x
Clamp ON
- polarity via Cooknell SA1 Summing Amplifier
207Bi source, approx centred on DSSSD, approx 3cm from DSSSD
File R30
shaping time 8uS
slow comparator 6 (dec)
start: 10.21 stop: 15.09
spectra saved to disk 16.10 BST (sic)
Pulser OFF
see attachments 1-4 (stat & rate hit patterns)
File R33
shaping time 8uS
slow comparator 5 (dec)
start: 16.03 stop: 17.44
spectra saved to disk 18.45 BST (sic)
Pulser OFF
Connect DSSSD-AIDA adaptor PCB screened cabling drain wires to adaptor PCB
mounting holes and secure with M3 socket bolts. With introduction of conductive
gasket should be equivalent to previous grounding via crocodile clips and gold-plated
Lemo-00 test input connectors.
18.19 Bias +200V, I_L +=6.760uA, ambient temperature +20.2 deg C
File R34
shaping time 8uS
slow comparator 8 (dec)
start: 18.34 stop: 10.19 19.2.16
spectra saved to disk 11.20 BST (sic)
Pulser OFF
see attachments 5-8
Attachments 9 & 10
DSSSD energy (~10keV/ch) versus DSSSD strip #
Note some eveidence for non-linearity at low amplitude for p+n strips (128-255) cf. n+n strips
(0-127)
Projection of above showing energy spectrum for one strip. Can observe 478 and 975keV K-lines
and prominent Landau peak near threshold. Threshold estimated at ~80-100keV (slow comparator 0x8).
m(p+n strips) = m(n+n strips) = 1, E(p+n strip)-E(n+n strip) = +/- 100keV
Enegy spectra ADC offset correct, no relative gain adjustment
Attachments 11, 12
Energy (p+n strip) versus E(n+n strip)
~10keV/channel, m(p+n strips) = m(n+n strips) = 1, with & without equal energy gate
Attachments 13, 14 & 15
Raw hit pattern, m(n+n strips) and m(p+n strips)
Attachment 16 - gzip'd tar file of sorted R34 spectra (see attachments 17 & 18)
Attachment 17 - FORTRAN user subroutine
Attachment 18 - ADC offset variables used by FORTRAN user subroutine
Attachment 19 - ADC offsets |
|
458
|
Sat Nov 19 02:43:39 2016 |
TD | Thursday 17 November |
10.15 DSSSD bias & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachments 3 & 4 |
|
801
|
Thu May 16 02:13:10 2019 |
CA, OH, TD | Thursday 16th May | 10:13 all system wide checks OK *except* nnaida7 fails ADC calibration
FEE64 temperatures OK - see attachment 1
good event statistics OK - see attachments 2
detector biases & leakage currents OK - see attachment 3
Temperature + deg 24.7C dew point +8.6 deg C RH 35.0%
Merger and TapeServer ok
10:30 DAQ, merger, TapeServer stop
Alpha run stopped at AIDA file TapeData/May19/R2_5
slow comparator threshold lowered to 10 keV (0xa)
DAQ start, not writing to file
good event statistics after lowering threshold, ok (attachment 4)
10:49 1.8.W spectra 20ms FSR - attachments 5 & 6
11:25 started writing to file R3 (sync test)
low threshold run at 5mb/s
11:33 DAQ stop (R3)
slow comparator threshold raised to 100 kev (0x64)
DAQ start, alpha run
Writing to file TapeData/May19/R4
18.49 alpha background
ASIC settings 2018Oct03-13.26.58
*except* slow comparator 0xa -> 0x64
BNC PB-4 Pulser OFF
FEE64 temperatures OK - see attachment 7
good event statistics - see attachments 8 - nnaida1 405k & nnaida17 368k, all other FEE64s c. 380Hz as
expected
ASIC check for *all* ASICs & FEE64s restored all FEE64 rates to expected c. 380Hz - see attachment 13
detector biases & leakage currents OK - see attachments 9 & 10
Merger OK - no error messages - see attachment 11
TapeServer OK - see attachment 12
all system wide checks OK *except* nnaida7 fails ADC calibration *and* Check Sync errors not counted Since
Baseline - see attachment 14
DAQ stopped May19/R4_3
aidas1> ls -l /TapeData/May19
total 19808048
-rw-rw-rw-. 1 npg npgstaff 1908736000 May 14 18:28 R1_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 02:30 R2_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 10:20 R2_1
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 18:08 R2_2
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 01:57 R2_3
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 09:45 R2_4
-rw-rw-rw-. 1 npg npgstaff 190447616 May 16 10:28 R2_5
-rw-rw-rw-. 1 npg npgstaff 1109327872 May 16 11:28 R3_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:39 R4_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:45 R4_1
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:50 R4_2
-rw-rw-rw-. 1 npg npgstaff 225312768 May 16 18:54 R4_3
-rw-rw-rw-. 1 npg npgstaff 52494336 May 16 19:10 R5_0
Wahtever the issue was it probably occurred before 18.39
DAQ RESET
DAQ SETUP
ASIC check for *all* ASICs & FEE64s
all system wide checks OK *except* nnaida7 fails ADC calibration
Sync all ASIC clocks using Re-SYNC
DAQ started May19/R5
19.23 1.8.W spectra - see attachments 15 & 16 |
|
316
|
Thu Jun 16 03:40:43 2016 |
TD | Thursday 16 June 2016 | 10.40 DAQ stalled AIDA75_30 c. 01.36
SYNC errors since baseline (start of AIDA75) - attachment 1
SYstem-wide checks ASIC clock timestamp and clock status OK for all FEE64s
Power-cycle & reboot
11.14 AIDA76
ASIC settings 2016Jun12-10.10.08
BNC PB-4 amplitude 50,000
11.19 AIDA77
BNC PB-4 amplitude 30,000
11.23 AIDA78
BNC PB-4 amplitude 10,000
11.28 AIDA79
BNC PB-4 amplitude 5,000
All *.L histograms saved c. 11.30 Thursday 16 June 2016
Example spectra - attachment 5
11.34 Water on floor by AIDA NIM bins/forward AIDA stand/EURICA - it would appear
that one or more cluster LN2 cryostat inlets have thawed are or thawing - failed fill
and/or blocked manifold?
Julabo FL11006 water level and flow looks OK
FEE temperatures OK - see attachment 4
Detector bias off
FEE64 power off
All AIDA power off
Source of water was determined to be wheeled air dehumdifier/cooler used to cool crates
in 19" rack to right of AIDA (looking upstream). This had a small tray tank to collect
water which was full to overflowing.
2x 60Co sources (#2530 and CD395) returned to cupboard B3F (between E12 & E17 stairwells)
|
|
786
|
Thu Nov 15 06:52:09 2018 |
OH | Thursday 15th November 16:00 - 24:00 | 15:51 DAQ continues - AIDA file RIBF148/R5_664
165Pm BigRIPS setting + 2.8mm Al degrader
ASIC settings 2018Oct03-13.26.58
from c. 09.00 13.11.18
n+n FEE64s Ibias LF feedback 0xb -> 0xd
HEC fast comparator threshold 0x20 -> 0xff
15:52 Beam out due to power fault somewhere.
15:53 Beam back
BRIKEN and BigRIPS start
BRIKEN file 181115_1553_165Pm_085.dlt
BigRIPS run 1070
AIDA on run R5_664
16:00 System wide checks all ok *Except nnaida7 fails adc calibration*
Leakage currents and bias ok - attachment 1
FEE Temps ok - attachment 2
Statistics ok - attachment 3
16:54 BRIKEN and BigRIPS stop
AIDA on file R5_675
16:55 BRIKEN starts run 181115_1654_165Pm_086.dlt
BigRIPS starts run 1071
AIDA on file R5_675
17:30 BRIKEBN and BigRIPS stop for BigRIPS team to get access
13:46 BRIKEN sends sync pulse resetting timestamp
AIDA on file R5_683
17:49 BRIKEN starts run 181115_1748_165Pm_087.dlt
bigRIPS starts run 1072
AIDA on file R5_683
18.00 System wide checks ok, except nnaida7 ADC calibration failure
FEE64 Temperatures ok (attachment 4)
Good event statistics ok (attachment 5)
Detector bias/Leakage currents ok (attachment 6)
18.04 Merger and TapeServer run ok - no error messages in terminals (attachments 7 and 8)
18:48 BigRIPS and BRIKEN stop
AIDA on file R5_693
18:49 BigRIPS starts run 1073
BRIKEN starts run 181115_1849_165Pm_088.dlt
AIDA on file R5_693
19:47 BgiRIPS and BRIKEN stop
AIDA on file R5_703
19:48 BigRIPS starts run 1074
BRIKEN starts run 181115_1947_165Pm_089.dlt
AIDA on file R5_703
20:54 bigRIPS and BRIKEN stop
AIDA on file R5_714
20:55 bigRIPS starts run 1075
BRIKEN starts run 181115_2053_165Pm_090.dlt
AIDA on file R5_714
21:25 System wide checks all ok *Except nnaida 7 fails adc calibration*
Bias and leakage currents ok - attachment 9
FEE Temps all ok - attachment 10
Statistics ok - attachment 11
21:55 BRIKEN and BigRIPS stop
AIDA on file R5_724
21:56 BigRIPS starts on run 1076
BRIKEN starts run
AIDA on file R5_724
22:55 BigRIPS and BRIKEN stop
AIDA on file R5_733
22:56 BRIKEN Starts run
BigRIPS starts run 1077
AIDA on file R5_733
23.53 Briken stops
AIDA on file R5_743
23.55 BRIKEN starts
bigRIPS run 1078
BRIKEN starts run 93
AIDA on file R5_743 |
|
785
|
Wed Nov 14 22:54:11 2018 |
LS | Thursday 15th November 08:00 - 16:00 |
08.10 BRIKEN stop
AIDA file RIBF148/R5_587
08.11 BRIKEN start
AIDA file RIBF148/R5_588
BRIKEN run 77
BigRIPS run 1062
08.16 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 1)
good event statistics ok (attachment 2)
detector bias/leakage currents ok (attachment 3)
Merger and TapeServer still ok
09.11 BRIKEN stop
AIDA file RIBF148/R5_598
09.13 BRIKEN start
AIDA file RIBF148/R5_598
BRIKEN run 78
BigRIPS run 1063
10.10 BRIKEN stop
AIDA file RIBF148/R5_608
10.12 BRIKEN start
AIDA file RIBF148/R5_608
BRIKEN run 79
BigRIPS run 1064
11.10 BRIKEN stop
AIDA file RIBF148/R5_618
11.12 BRIKEN start
AIDA file RIBF148/R5_618
BRIKEN run 80
BigRIPS run 1065
11.17 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 4)
good event statistics ok (attachment 5)
detector bias/leakage currents ok (attachment 6)
Merger and TapeServer still ok
12:10 BigRIPS and BRIKEN stop
AIDA on file R5_628
12:11 BRIKEN start
AIDA on file R5_628
BigRIPS run 1066
BRIKEN run 81 181115_1211_165Pm_081.dlt
13.10 BRIKEN stop
AIDA file RIBF148/R5_638
13.12 BRIKEN start
AIDA file RIBF148/R5_638
BRIKEN run 82
BigRIPS run 1067
13.32 AIDA file RIBF148/R5_642
BRIKEN stopped
Turning beam off to access area
13.50 AIDA file RIBF148/R5_644
beam back on
BRIKEN run 83
BigRIPS run 1068
14.26 MIDASsort analysis file RIBF148/R5_648 - all ADC data synchronised - attachment 7
analysis of file RIBF148/R5_648 - attachment 8
nnaida19 dead time ~0.5% - all other deadtimes lower or 0% - no timewarps
14.35 1.8.W spectra layout ID 8 (attachment 9)
14.50 BRIKEN stop
AIDA file RIBF148/R5_654
14.51 BRIKEN start
AIDA file RIBF148/R5_654
BRIKEN run 83
BigRIPS run 1068
15.10 1.8.H high energy channel spectra (attachment 10)
15.35 beam off
AIDA file RIBF148/R5_662
BRIKEN and BigRIPS stopped run |
|
784
|
Wed Nov 14 14:46:47 2018 |
CA | Thursday 15th November 00:00 - 08:00 | 23.58 DAQ continues ok (RIBF148/R5_505)
00.09 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 1)
good event statistics ok (attachment 2)
detector bias/leakage currents ok (attachment 3)
00.13 Merger and TapeServer run ok (attachment 4/5)
00.26 BRIKEN stop
AIDA file RIBF148/R5_509
00.29 BRIKEN start
AIDA file RIBF148/R5_510
BRIKEN run 70
BigRIPS run 1055
01.46 BRIKEN stop
AIDA file RIBF148/R5_523
01.49 BRIKEN start
AIDA file RIBF148/R5_523
BRIKEN run 71
BigRIPS run 1056
02.05 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 6)
good event statistics ok (attachment 7)
detector bias/leakage currents ok (attachment 8)
Merger and TapeServer still ok
02.34 XY hit patterns (attachment 9)
Ex vs Ey plots (attachment 10)
HEC spectra (attachment 11)
LEC spectra (attachment 12)
02.49 BRIKEN stop
AIDA file RIBF148/R5_534
02.50 BRIKEN start
AIDA file RIBF148/R5_534
BRIKEN run 72
BigRIPS run 1057
03.26 zeroed all spectra on online analysis and MIDASsort
04.04 BRIKEN stop
AIDA file RIBF148/R5_546
04.05 BRIKEN start
AIDA file RIBF148/R5_546
BRIKEN run 73
BigRIPS run 1058
04.10 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 13)
good event statistics ok (attachment 14)
detector bias/leakage currents ok (attachment 15)
Merger and TapeServer still ok
05.06 BRIKEN stop
AIDA file RIBF/R5_556
05.07 BRIKEN start
AIDA file RIBF148/R5_557
BRIKEN run 74
BigRIPS run 1059
05.08 First 200ms of decay correlations in all detectors
comparison between different Al degrader thickness values (3mm, 2.3mm, 2.8mm)
see attachments 16, 17 and 18 - graphs labelled with detector number and Al degrader thickness
06.09 BRIKEN stop
AIDA file RIBF148/R5_567
06.11 BRIKEN start
AIDA file RIBF148/R5_567
BRIKEN run 75
BigRIPS run 1060
06.16 system wide checks ok, except nnaida7 ADC calibration failure
FEE64 temperatures ok (attachment 19)
good event statistics ok (attachment 20)
detector bias/leakage currents ok (attachment 21)
Merger and TapeServer still ok
06.17 ASIC check load - ok
06.34 XY hit patterns (attachment 22)
Ex vs Ey plots (attachment 23)
HEC spectra (attachment 24)
LEC spectra (attachment 25)
07:12 BRIKEN stop
AIDA file RIBF148/R5_578
07:15 BRIKEN start
AIDA file RIBF148/R5_578
BRIKEN run 76
BigRIPS run 1061
|
|
662
|
Thu Jun 15 02:56:32 2017 |
TD, OH | Thursday 15 June | 10.52 DAQ continues
AIDA file RIBF148/R8_39
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0x64
LEC/MEC fast comparator 0x14
10.54 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachment 4
No warnings/errors reported by merger since start of RIBF148/R3 - see attachment 5
*all* system wide checks OK (zero fails)
11.02 analysis file RIBF148/R8_39 - zero deadtime, 222x MBS and zero ts timewarps - see attachment 6
correlation scaler trigger ~ 950/3 ~ 320Hz
15.12 online analysis
ADC & disc data synchronised - note the effect of the higher slow comparator threshold on the after-pulse
- see attachment 7
per DSSSD m_p versus m_n (LEC) - see attachments 8
per DSSSD x versus y (LEC) - see attachment 9
per DSSSD E_p versus E_n (LEC) - 512x512 spectra - nominal 20keV per channel - see attachment 10
Spectra show light particles detected from last night's 238U beam test - no HEC data due to 10cm Pb wall
It should be straightforward to separate the alpha background from this data using the change in LEC rates
and the light particle data will also provide a good check of the calibration.
11.17 Stop DAQ
AIDA file RIBF148/R8_40
online histograms & SortSas spectra zero'd
saw tooth noise FEE64s p+n junction strips not observed
clover detectors re-installed but not cabled or biased
3He detectors are on
Si dE and variable degrader was removed yesterday
11.19 Start DAQ
AIDA file RIBF148/R9
Check ASIC control x2
13.15 Detector biases & leakage currents OK - see attachments 11 & 12
16.45 Clover detectors cabled and bias applied
17.33 DAQ continues
AIDA file RIBF148/R9_6
nnaida13 & nnaida11 1.8.W spectra - nnaida13 shows evidence of high frequency noise modulated
with a period of ~400us cf. https://elog.ph.ed.ac.uk/AIDA/661
18.01 DAQ stop
AIDA file RIBF148/R9_6
18.09 *** NEW FEE64 FIRMWARE ***
New RunControl/sys.tcl and Check/check.js .tcl .tml
18.48 DAQ start
AIDA file RIBF148/R10
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
*except*
slow comparator 0x64
LEC/MEC fast comparator 0x14
19.03 online analysis
ADC & disc data synchronised - 20.48us/channel - see attachment 15
For all combinations of x-y strips (LEC events) calculate
IF ( ihit( i ) .AND. ihit( j ) ) THEN
tdiff1 = ihit_ts(i)-e_time
tdiff2 = ihit_ts(j)-e_time
CALL inc1d( 500, tdiff1 + 2000 )
CALL inc1d( 506, tdiff2 + 2000 )
CALL inc2d( 2600, tdiff1, tdiff2 )
ENDIF
where
e_time = 100MHz timestamp of first ADC word of event
ihit_ts(i) = 100MHz timestamp of ADC word i of event
see attachments 16-17
19.21 Current MONLOCK status - see attachment 18 |
|
384
|
Thu Oct 13 06:07:43 2016 |
TD & CG | Thursday 13 October |
11.40 Power cycle AIDA FEE64s
Set TS_SYNC_PHASE 0
DSSSD bias/leakage current OK - see attachment 1-2
FEE64 temperatures OK - see attachment 3
*All* system-wide checks OK
B2F/F11 temperature + deg C, d.p. + deg C,RH %
ASIC settings 2016Sep02-18.17.01
slow comparator 0x10 -> 0x0a
LEC/MEC fast comparators # 1, 55 & 58 disabled for all FEE64s
Master MACB serial #13 (see https://elog.ph.ed.ac.uk/AIDA/367)
Master MACB mode 5
12.15 DAQ starts (file Sept2016/R24)
15.16 DAQ stops OK
15.18 DAQ starts (R25)
Pulser walkthrough
BNC PB-4 amplitudes 10,000 - 90,000 @ 10,000 step
See attachment 4
Spectra saved 13.10.16 15.32 (08.32 FEE64s)
15.30 DAQ stops OK
15.38 DAQ starts (R26)
Pulser walkthrough
BNC PB-4 amplitudes 8,000 - 2,000 @ 2,000 step
See attachment 5
Spectra saved 13.10.16 15.47 (08.47 FEE64s)
15.45 DAQ stops
15.50 DAQ starts (R27)
LEC/MEC FSR 20MeV -> 1GeV
BNC PB-4 amplitude 90,000
Spectra saved 13.10.16 16.07 (09.05 FEE64s)
16.05 DAQ stops
16.12 DAQ starts (R28)
LEC/MEC FSR 1GeV -> 20MeV
BNC PB-4 off (noise + background activity only)
Spectra saved 13.10.16 16:49 (saved 09.49 FEE64s)
16.48 DAQ stops
16.57 DAQ starts (R29)
BNC PB-4 90,000 amplitude ~23Hz freq.
17.26 Lost SYNC pulses. Merger+TapeServer stopped writing to file (noticed 18.20)
18.25 R29 closed.
19:20 NIM bin supplying TTL clock to master MACB failed at or around the same time as the DAQ stop occurred.
Need to replace NIM bin before clock can be supplied.
21.20 DAQ starts (R32)
23.51 DAQ found stopped, most recent file R32_26 (last access 22.34 13.10.16)
23.56 Restarted merger & immediately requested DAQ STOP - OK
DAQ reset & setup
System-wide tests all OK
00.01 DAQ starts (R33) |
|
839
|
Thu Jun 13 00:30:17 2019 |
CA, CB, TD, CG, OH, DK | Thursday 13 June | 08.32 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C
Water level c. 70% M-H markers + 0.5 jugful -> c. 80% M-H markers
Temperature +24.0 deg C dew point +9.6 deg C RH 39.0%
DAQ continues OK
ASIC settings 2019May19-17.54.03
slow comparator 0xa
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics - OK - see attachment 4
8x <20k 23x < 50k 24x <100k cf. 7x <20k 23x < 50k 24x <100k yesterday evening
Merger OK - see attachment 5
TapeServer OK - see attachment 6
p+n FEE64s 1.8.W spectra 20us FSR - attachment 7
n+n FEE64s 1.8.W spectra 20us FSR - attachment 8
1.8.L spectra - see attachments 9 & 10
nnaida1 85 ch FWHM, nnaida3 86 ch FWHM - cf. 75 & 79 ch FWHM respectively 17.04 Tuesday 11 June
FEE64 Rate spectra - attachment 11
Check ASIC Control *all* FEE64s & ASICs x2
Check ASIC Control x3
FEE64 ASIC
13 1
14 4
16 4
19 3
21 2
FEE64 Rate spectra - attachment 12 - some channels recovered
08.45 ADC data synchronised - attachment 13
08.52 zero all histograms
zero DAQ stats
08.56 ASIC settings saved to new DB key 2019Jun13-08.56.35
includes slow comparator 0xa
DAQ options updated
15:18
DAQ continues okay. Rates seem ok, see attachment 14.
Biases shown as attachment 15 -- looks fine.
(These are all as before we assume)
ASIC settings 2019May19-17.54.03
slow comparator 0xa
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
all system wide checks OK *except* nnaida7 fails ADC calibration
FEE64 temperatures OK - see attachment 16
Merge ok, 570k items per second, see attachment 17
TapeServer not storing but sitting around 4 MBytes/sec, see attachment 18 |
|
907
|
Thu Oct 12 13:02:50 2023 |
TD | Thursday 12 October contd. |
ASIC settings 2021Apr29-13-16-00
slow comparator 0xa ( all p+n junction FEE64s ) and 0xf ( all n+n Ohmic FEE64s )
BNC PB-5
amplitude 10.0V
attenuation x10
tail pulse
decay time 1ms
frequency 25Hz
polarity -
PB-5 output direct to aida02 *only*
CAEN N1419ET non-floating outputs ( internal LK fitted )
ch2 - polarity
HV cable - standard coaxial cable to aida12 chained to aida03 & aida11
chain ( Lemo-00 cables ) adaptor PCB gnd from aida09 to aida01 & aida10
ground cable from aida04 adaptor PCB gnd to aida12, aida02 & aida09
aida04 LK1 ( local gnd ) fitted
aida03 LK3 fitted ( DSSSD PCB gnd )
DSSSD bias -150V -6.510uA - attachment 1
ADC data item stats - attachment 2
p+n rates dominated by hot channels - most p+n channels < 1Hz/channel
n+n rates c. 10Hz/channel
per FEE64 Rate spectra - attachment 3-5
aida02 1.8.L pulser peak width 102 ch FWHM ( 70 keV FWHM )
aida02 *.*.L spectra - attachments 6-9
common x & y scales for all spectra - peak height proxy for peak width
all channels have similar pulser peak widths
aida02 3.*.W spectra - 20us, 200us, 2ms & 20ms FSR - attachments 10-17
per p+n FEE64 1.8.W spectra - 20us, 200us, 2ms & 20ms FSR - attachments 18-25
per n+n FEE64 1.8.W spectra - 20us, 200us, 2ms & 20ms FSR - attachments 26-33
DSSSD bias -150V -6.510uA - attachment 34
ADC data item stats - attachment 35
p+n rates dominated by hot channels - most p+n channels < 1Hz/channel
n+n rates c. 10Hz/channel
per FEE64 Rate spectra - attachment 36-38
aida12 1.8.L pulser peak width 56 ch FWHM ( 39keV FWHM )
aida12 *.*.L spectra - attachments 39-42
common x & y scales for all spectra - peak height proxy for peak width
60 channels have similar pulser peak widths
4 channels show peak widths c. 2x larger ( 'hot' channels )
aida12 3.*.W spectra - 20us, 200us, 2ms & 20ms FSR - attachments 43-50 |
|
906
|
Thu Oct 12 09:12:34 2023 |
TD | Thursday 12 October | 10.10 Water flow & temp OK
Power ON
All system wide checks OK
ASIC settings 2021Apr29-13-16-00
slow comparator 0x64
BNC PB-5
amplitude 10.0V
attenuation x10
tail pulse
decay time 1ms
frequency 25Hz
polarity -
PB-5 output direct to aida01 *only*
CAEN N1419ET non-floating outputs ( internal LK fitted )
ch2 - polarity
HV cable - standard coaxial cable to aida12 chained to aida03, aida11, aida09, aida01 & aida10
aida04 LK1 ( local gnd ) fitted
ground cable from aida04 adaptor PCB gnd to aida12 & aida02
aida03 LK3 fitted ( DSSSD PCB gnd )
DSSSD bias -150V -6.300uA - attachment 1
FEE64 temps OK - attachment 2
ADC data item stats - attachment 3
per FEE64 Rate spectra - attachment 4
ignore aida06 & adida08 - not connected to anything
ignore known issue of high rates aida04 asic #1 and aida10 asic #4 - remediable
aida01 1.8.L pulser peak width 75 ch FWHM ( 53keV FWHM )
1.8.W spectra - 20us FSR - attachments 5 & 6
10.35 slow comparator 0x64 -> 0xa ( all p+n junction FEE64s ) and 0xf ( all n+n Ohmic FEE64s )
ADC data item stats - attachment 7
per FEE64 Rate spectra - attachment 8-10
p+n rates dominated by hot channels - most p+n channels < 1Hz/channel
n+n rates c. 50Hz/channel
per p+n FEE64 1.8.W spectra - 20us, 200us & 2ms FSR - attachments 11-13
per n+n FEE64 1.8.W spectra - 20us, 200us & 2ms FSR - attachments 14-16
12.10 HV cable - standard coaxial cable to aida12 chained to aida03 & aida11
chain ( Lemo-00 cables ) adaptor PCB gnd from aida09 to aida01 & aida10
DSSSD bias -150V -6.535uA - attachment 17
ADC data item stats - attachment 18
per FEE64 Rate spectra - attachment 19-21
aida01 1.8.L pulser peak width 78 ch FWHM ( 55keV FWHM )
1.8.W spectra - 20us FSR - attachments 22 & 23
12.40 HV cable - standard coaxial cable to aida12 chained to aida03 & aida11
chain ( Lemo-00 cables ) adaptor PCB gnd from aida09 to aida01 & aida10
ground cable from aida04 adaptor PCB gnd to aida12, aida02 & aida09
DSSSD bias -150V -6.535uA - attachment 24
ADC data item stats - attachment 25
per FEE64 Rate spectra - attachment 26-28
aida01 1.8.L pulser peak width 61 ch FWHM ( 42keV FWHM )
1.8.W spectra - 20us FSR - attachments 29-32
aida01 *.*.L spectra - attachments 33-36
common x & y scales - pulser peak height proxy for peak width
aida01 3.*.W spectra - 20us FSR - attachments 37-39
per p+n FEE64 1.8.W spectra - 20us, 200us, 2ms & 20ms - attachments 40-47 |
|
562
|
Thu May 11 05:43:30 2017 |
TD, OH | Thursday 11 May | 13.43 DAQ continues OK
Current file May2017/R6_123
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x20
LEC/MEC fast comparator 0xff
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
'good events' statistics OK - see attachment 4
No warnings/errors reported by merger since DAQ GO - see attachment 5
*all* system wide checks OK
13.37 E17/F11 ambient temperature +24.4 deg C, RH 37.3%, d.p. +9.1 deg C
13.58 1.8.L ADC spectra - see attachments 6 & 7
1.8.W waveforms - see attachments 8-11
14.16 Analysis of data file R6_124 - see attachment 12
Zero AIDA pause/resume
Zero idle-time
AIDA SYNC100 variations ~20/468430
18.36 DAQ continues OK
Current file May2017/R6_137
Detector biases & leakage currents OK - see attachments 13 & 14
FEE64 Temperatures OK - see attachment 15
'good events' statistics OK - see attachment 16
*all* system wide checks OK |
|
451
|
Thu Nov 10 12:02:24 2016 |
TD, OH, CG | Thursday 10 November |
21.17 DAQ starts (R30)
Pulser walkthrough
Amplitude 90,000 - 10,000 @ 10,000 step
x5 attenuator IN
t_r 50ns tau_d 50us
polarity -, tail pulse, delay MIN
frequency 250Hz range
21.30 DAQ stops OK
21.32 DAQ starts (R31)
Pulser walkthrough
Amplitude 10,000 - 2,000 @ 2,000 step
21.40 DAQ stops OK
21.44 DAQ starts (R32)
Background
BNC PB-4 pulser OFF
21.59 DAQ stops OK
23.45 Started R35 so Jorge can do some tests.
No storage mode.
00.20 Carried out manual fill on LN2 in advance of beam arriving later (~03.00).
Took around 20mins.
Continued writing to R35 after soft reset of DAQ. |
|
353
|
Thu Sep 1 03:45:34 2016 |
TD | Thursday 1 September | 13.33 R11 starts
ASIC settings 2016Aug20-15.34.53
Discriminator masks -> 0x0
Slow comparator 0x10
LEC/MEC fast comparator 0xff
From Correlation Status & Control tab change Trigger delay 0x180
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
t_r 50ns tau_d 50us
- polarity
INT ref, delay MIN, tail pulse
Frequency c. 5Hz
B2F/F11 temp +24.8 deg C, d.p. +11.9 deg C, RH 44.8%
DSSSD bias/leakage current OK - see attachments 1-2
FEE64 temperatures OK - see attachment 3
System-wide checks OK - see attachments 4-9
AIDA SYNC, PAUSE, RESUME, Correlation L, SYNC time warp, Good Events, AIDA disc, nnaida6, nnaida5 & nnaida20 statistics - see
attachments 10-20
Good event rate varies from 5-320k / FEE64
Merger/tapeserver - see attachments 21-22
Merged data rate ~2-3M data items/s, c. 16M to disk
Analysis of R11_93 - FEE64 data synchronised - see attachment 23
aidas1> ./analyser2 /TapeData/Aug2016/R11_93
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ADC data: block: 3402 ptr: 15985 data: 0xC4C37FDB module: 19 fail: 0 range: 0 id: 1219 channel: 3 adc: 32731 ts:
0x00000120C00000A0 OLD: ts: 0x00000120D000008D tag: 3 type: 0
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 170966247 ( 1387907.5 Hz)
Other data format: 90121753 ( 731610.3 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 106 ( 0.9 Hz)
RESUME: 106 ( 0.9 Hz)
SYNC100: 1124303 ( 9127.1 Hz)
FEE64 disc: 88996299 ( 722473.8 Hz)
MBS info: 939 ( 7.6 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 571 ( 4.6 Hz)
Timewarps: ADC: 1 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 123.183 s
FEE module #: 1 elapsed dead time 0.370 s
FEE module #: 2 elapsed dead time 0.317 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 1.058 s
FEE module #: 6 elapsed dead time 2.581 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.130 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.000 s
FEE module #: 12 elapsed dead time 0.000 s
FEE module #: 13 elapsed dead time 1.078 s
FEE module #: 14 elapsed dead time 0.172 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.223 s
FEE module #: 18 elapsed dead time 0.017 s
FEE module #: 19 elapsed dead time 0.089 s
FEE module #: 20 elapsed dead time 0.000 s
FEE module #: 21 elapsed dead time 2.291 s
FEE module #: 22 elapsed dead time 0.450 s
FEE module #: 23 elapsed dead time 0.000 s
FEE module #: 24 elapsed dead time 0.000 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 21.035s ( 1521.263 blocks/s, 95.079 Mb/s)
Verbose data dump around time warp (file R11_93, block 3402, ptr 15985)
*** ADC data: block: 3402 ptr: 15901 data: 0xC5777559 module: 21 fail: 0 range: 0 id: 1399 channel: 55 adc: 30041 ts:
0x00000120CFFFF895
*** FEE64 discriminator: block: 3402 ptr: 15903 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFF895
*** ADC data: block: 3402 ptr: 15905 data: 0xC17A793F module: 5 fail: 0 range: 0 id: 378 channel: 58 adc: 31039 ts:
0x00000120CFFFF895
*** FEE64 discriminator: block: 3402 ptr: 15907 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFF898
*** FEE64 discriminator: block: 3402 ptr: 15909 data: 0x82640080 module: 2 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFF89A
*** FEE64 discriminator: block: 3402 ptr: 15911 data: 0x81640080 module: 1 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFF89B
*** ADC data: block: 3402 ptr: 15913 data: 0xC5018140 module: 20 fail: 0 range: 0 id: 1281 channel: 1 adc: 33088 ts:
0x00000120CFFFF8D5
*** ADC data: block: 3402 ptr: 15915 data: 0xC3617FA1 module: 13 fail: 0 range: 0 id: 865 channel: 33 adc: 32673 ts:
0x00000120CFFFF92D
*** ADC data: block: 3402 ptr: 15917 data: 0xC5417DDE module: 21 fail: 0 range: 0 id: 1345 channel: 1 adc: 32222 ts:
0x00000120CFFFF95D
*** ADC data: block: 3402 ptr: 15919 data: 0xC57A7D7B module: 21 fail: 0 range: 0 id: 1402 channel: 58 adc: 32123 ts:
0x00000120CFFFF95D
*** ADC data: block: 3402 ptr: 15921 data: 0xC3687F55 module: 13 fail: 0 range: 0 id: 872 channel: 40 adc: 32597 ts:
0x00000120CFFFF9F5
*** FEE64 discriminator: block: 3402 ptr: 15923 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFB5B
*** FEE64 discriminator: block: 3402 ptr: 15925 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFB5C
*** FEE64 discriminator: block: 3402 ptr: 15927 data: 0x82640080 module: 2 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFB5F
*** ADC data: block: 3402 ptr: 15929 data: 0xC35F7DAD module: 13 fail: 0 range: 0 id: 863 channel: 31 adc: 32173 ts:
0x00000120CFFFFB85
*** ADC data: block: 3402 ptr: 15931 data: 0xC3307F91 module: 12 fail: 0 range: 0 id: 816 channel: 48 adc: 32657 ts:
0x00000120CFFFFBB5
*** ADC data: block: 3402 ptr: 15933 data: 0xC5A67F6D module: 22 fail: 0 range: 0 id: 1446 channel: 38 adc: 32621 ts:
0x00000120CFFFFBDD
*** ADC data: block: 3402 ptr: 15935 data: 0xC0C0845E module: 3 fail: 0 range: 0 id: 192 channel: 0 adc: 33886 ts:
0x00000120CFFFFC35
*** ADC data: block: 3402 ptr: 15937 data: 0xC3657ED9 module: 13 fail: 0 range: 0 id: 869 channel: 37 adc: 32473 ts:
0x00000120CFFFFC4D
*** FEE64 discriminator: block: 3402 ptr: 15939 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFC77
*** FEE64 discriminator: block: 3402 ptr: 15941 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFC7A
*** FEE64 discriminator: block: 3402 ptr: 15943 data: 0x81640080 module: 1 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFC7C
*** FEE64 discriminator: block: 3402 ptr: 15945 data: 0x82640080 module: 2 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFC7C
*** ADC data: block: 3402 ptr: 15947 data: 0xC4DC8041 module: 19 fail: 0 range: 0 id: 1244 channel: 28 adc: 32833 ts:
0x00000120CFFFFCB8
*** FEE64 discriminator: block: 3402 ptr: 15949 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFCC6
*** ADC data: block: 3402 ptr: 15951 data: 0xC38C7EF8 module: 14 fail: 0 range: 0 id: 908 channel: 12 adc: 32504 ts:
0x00000120CFFFFD3D
*** ADC data: block: 3402 ptr: 15953 data: 0xC4817ED8 module: 18 fail: 0 range: 0 id: 1153 channel: 1 adc: 32472 ts:
0x00000120CFFFFD85
*** ADC data: block: 3402 ptr: 15955 data: 0xC3577EE4 module: 13 fail: 0 range: 0 id: 855 channel: 23 adc: 32484 ts:
0x00000120CFFFFDDD
*** ADC data: block: 3402 ptr: 15957 data: 0xC1B67F41 module: 6 fail: 0 range: 0 id: 438 channel: 54 adc: 32577 ts:
0x00000120CFFFFE35
*** FEE64 discriminator: block: 3402 ptr: 15959 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFF44
*** ADC data: block: 3402 ptr: 15961 data: 0xC5517FCD module: 21 fail: 0 range: 0 id: 1361 channel: 17 adc: 32717 ts:
0x00000120CFFFFF9D
*** ADC data: block: 3402 ptr: 15963 data: 0xC5957FEA module: 22 fail: 0 range: 0 id: 1429 channel: 21 adc: 32746 ts:
0x00000120CFFFFFC5
*** ADC data: block: 3402 ptr: 15965 data: 0xC5B37E90 module: 22 fail: 0 range: 0 id: 1459 channel: 51 adc: 32400 ts:
0x00000120CFFFFFC5
*** FEE64 discriminator: block: 3402 ptr: 15967 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120CFFFFFD9
*** ADC data: block: 3402 ptr: 15969 data: 0xC4B77FCE module: 18 fail: 0 range: 0 id: 1207 channel: 55 adc: 32718 ts:
0x00000120CFFFFFDD
*** ADC data: block: 3402 ptr: 15971 data: 0xC5047FBE module: 20 fail: 0 range: 0 id: 1284 channel: 4 adc: 32702 ts:
0x00000120CFFFFFDD
*** ADC data: block: 3402 ptr: 15973 data: 0xC3627FFD module: 13 fail: 0 range: 0 id: 866 channel: 34 adc: 32765 ts:
0x00000120D0000035
*** FEE64 discriminator: block: 3402 ptr: 15975 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D0000059
*** FEE64 discriminator: block: 3402 ptr: 15977 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120D000005D
*** FEE64 discriminator: block: 3402 ptr: 15979 data: 0x82640080 module: 2 information type: 6 information field: 0x00040080 ts:
0x00000120D000005F
*** ADC data: block: 3402 ptr: 15981 data: 0xC5437FC7 module: 21 fail: 0 range: 0 id: 1347 channel: 3 adc: 32711 ts:
0x00000120D0000065
*** ADC data: block: 3402 ptr: 15983 data: 0xC583802E module: 22 fail: 0 range: 0 id: 1411 channel: 3 adc: 32814 ts:
0x00000120D000008D
*** ADC data: block: 3402 ptr: 15985 data: 0xC4C37FDB module: 19 fail: 0 range: 0 id: 1219 channel: 3 adc: 32731 ts:
0x00000120C00000A0 OLD: ts: 0x00000120D000008D tag: 3 type: 0
*** ADC data: block: 3402 ptr: 15985 data: 0xC4C37FDB module: 19 fail: 0 range: 0 id: 1219 channel: 3 adc: 32731 ts:
0x00000120C00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15987 data: 0x8140120D module: 1 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15989 data: 0x8240120D module: 2 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15991 data: 0x8340120D module: 3 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15993 data: 0x8440120D module: 4 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15995 data: 0x8540120D module: 5 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15997 data: 0x8640120D module: 6 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 15999 data: 0x8740120D module: 7 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16001 data: 0x8840120D module: 8 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16003 data: 0x8940120D module: 9 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16005 data: 0x8A40120D module: 10 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16007 data: 0x8B40120D module: 11 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16009 data: 0x8C40120D module: 12 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16011 data: 0x8D40120D module: 13 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16013 data: 0x8E40120D module: 14 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16015 data: 0x8F40120D module: 15 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16017 data: 0x9040120D module: 16 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16019 data: 0x9140120D module: 17 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16021 data: 0x9240120D module: 18 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16023 data: 0x9340120D module: 19 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16025 data: 0x9440120D module: 20 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16027 data: 0x9540120D module: 21 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16029 data: 0x9640120D module: 22 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16031 data: 0x9740120D module: 23 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** SYNC100 timestamp: block: 3402 ptr: 16033 data: 0x9840120D module: 24 information type: 4 information field: 0x0000120D ts:
0x00000120D00000A0
*** ADC data: block: 3402 ptr: 16035 data: 0xC4BA7DF1 module: 18 fail: 0 range: 0 id: 1210 channel: 58 adc: 32241 ts:
0x00000120D00000A5
*** FEE64 discriminator: block: 3402 ptr: 16037 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D00000A9
*** FEE64 discriminator: block: 3402 ptr: 16039 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120D00000AC
*** ADC data: block: 3402 ptr: 16041 data: 0xC5F7812E module: 23 fail: 0 range: 0 id: 1527 channel: 55 adc: 33070 ts:
0x00000120D000010D
*** ADC data: block: 3402 ptr: 16043 data: 0xC5467E32 module: 21 fail: 0 range: 0 id: 1350 channel: 6 adc: 32306 ts:
0x00000120D000012D
*** ADC data: block: 3402 ptr: 16045 data: 0xC4C4801A module: 19 fail: 0 range: 0 id: 1220 channel: 4 adc: 32794 ts:
0x00000120D0000168
*** ADC data: block: 3402 ptr: 16047 data: 0xC54F7E07 module: 21 fail: 0 range: 0 id: 1359 channel: 15 adc: 32263 ts:
0x00000120D00001F5
*** ADC data: block: 3402 ptr: 16049 data: 0xC1907F13 module: 6 fail: 0 range: 0 id: 400 channel: 16 adc: 32531 ts:
0x00000120D000021D
*** ADC data: block: 3402 ptr: 16051 data: 0xC1B76F59 module: 6 fail: 0 range: 0 id: 439 channel: 55 adc: 28505 ts:
0x00000120D000021D
*** FEE64 discriminator: block: 3402 ptr: 16053 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D0000268
*** ADC data: block: 3402 ptr: 16055 data: 0xC519804A module: 20 fail: 0 range: 0 id: 1305 channel: 25 adc: 32842 ts:
0x00000120D00002FD
*** FEE64 discriminator: block: 3402 ptr: 16057 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D0000326
*** ADC data: block: 3402 ptr: 16059 data: 0xC3A57F86 module: 14 fail: 0 range: 0 id: 933 channel: 37 adc: 32646 ts:
0x00000120D000037D
*** ADC data: block: 3402 ptr: 16061 data: 0xC5707DD1 module: 21 fail: 0 range: 0 id: 1392 channel: 48 adc: 32209 ts:
0x00000120D0000385
*** ADC data: block: 3402 ptr: 16063 data: 0xC5B57F01 module: 22 fail: 0 range: 0 id: 1461 channel: 53 adc: 32513 ts:
0x00000120D00003AD
*** ADC data: block: 3402 ptr: 16065 data: 0xC2457E6F module: 9 fail: 0 range: 0 id: 581 channel: 5 adc: 32367 ts:
0x00000120D00003BD
*** FEE64 discriminator: block: 3402 ptr: 16067 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D00003BD
*** ADC data: block: 3402 ptr: 16069 data: 0xC4C181BD module: 19 fail: 0 range: 0 id: 1217 channel: 1 adc: 33213 ts:
0x00000120D00003C0
*** ADC data: block: 3402 ptr: 16071 data: 0xC4ED80E8 module: 19 fail: 0 range: 0 id: 1261 channel: 45 adc: 33000 ts:
0x00000120D00003C0
*** ADC data: block: 3402 ptr: 16073 data: 0xC4F6812B module: 19 fail: 0 range: 0 id: 1270 channel: 54 adc: 33067 ts:
0x00000120D00003C0
*** ADC data: block: 3402 ptr: 16075 data: 0xC3457F08 module: 13 fail: 0 range: 0 id: 837 channel: 5 adc: 32520 ts:
0x00000120D000041D
*** ADC data: block: 3402 ptr: 16077 data: 0xC37C7FB1 module: 13 fail: 0 range: 0 id: 892 channel: 60 adc: 32689 ts:
0x00000120D000041D
*** FEE64 discriminator: block: 3402 ptr: 16079 data: 0x85640080 module: 5 information type: 6 information field: 0x00040080 ts:
0x00000120D000043B
*** FEE64 discriminator: block: 3402 ptr: 16081 data: 0x86640080 module: 6 information type: 6 information field: 0x00040080 ts:
0x00000120D000043B
*** FEE64 discriminator: block: 3402 ptr: 16083 data: 0x81640080 module: 1 information type: 6 information field: 0x00040080 ts:
0x00000120D000043F
*** FEE64 discriminator: block: 3402 ptr: 16085 data: 0x82640080 module: 2 information type: 6 information field: 0x00040080 ts:
0x00000120D0000440
*** ADC data: block: 3402 ptr: 16087 data: 0xC38A7F89 module: 14 fail: 0 range: 0 id: 906 channel: 10 adc: 32649 ts:
0x00000120D0000445
*** ADC data: block: 3402 ptr: 16089 data: 0xC3A68005 module: 14 fail: 0 range: 0 id: 934 channel: 38 adc: 32773 ts:
0x00000120D0000445
*** ADC data: block: 3402 ptr: 16091 data: 0xC3B07E25 module: 14 fail: 0 range: 0 id: 944 channel: 48 adc: 32293 ts:
0x00000120D0000445
*** ADC data: block: 3402 ptr: 16093 data: 0xC5737ED1 module: 21 fail: 0 range: 0 id: 1395 channel: 51 adc: 32465 ts:
0x00000120D000044D
*** ADC data: block: 3402 ptr: 16095 data: 0xC5A17F32 module: 22 fail: 0 range: 0 id: 1441 channel: 33 adc: 32562 ts:
0x00000120D0000475
*** ADC data: block: 3402 ptr: 16097 data: 0xC4FB80F3 module: 19 fail: 0 range: 0 id: 1275 channel: 59 adc: 33011 ts:
0x00000120D0000488
*** ADC data: block: 3402 ptr: 16099 data: 0xC37F7E9C module: 13 fail: 0 range: 0 id: 895 channel: 63 adc: 32412 ts:
0x00000120D00004E5
*** ADC data: block: 3402 ptr: 16101 data: 0xC1837FED module: 6 fail: 0 range: 0 id: 387 channel: 3 adc: 32749 ts:
0x00000120D000053D
Note - system-wide checks still OK despite time warp observed above
no errors reported by merger since start of R11
Free memory before and after saving all L and H spectra to disk - see attachments 24-25
Some merger errors observed during save of all L and H spectra to disk - see attachment 26
FEE64 temperatures - Julabo FL11006 set point + 20 deg C - see attachment 27
set point + 16 deg C - see attachment 28
Temperatures decrease typically ~ 2-4 deg C which implies that the coolant loop is working as expected.
However, +16 deg C is marginal due to relative humidity variations ~40-55% corresponding to Dew Point
temperatures of ~12-14 deg C. Returning Julabo FL11006 set point to +20 deg C. |
|
756
|
Thu Nov 1 00:24:23 2018 |
TD, OH, CA | Thursday 1 November | 09.24 DAQ continues OK - current file Oct18/R12_116
alpha background run
09.20 all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics OK *except* nnaida17 c. 400k - see attachment 4
nnaida2 rate due to one hot channel as before
Merger - Link16 errors reported - see attachment 5
TapeServer OK - see attachment 6
problem with nnaida17 rate resolved with ASIC check load - see attachment 7
1.8.L spectra - see attachments 7 & 8
N.B. evidence of minimally ionising particles (presumably protons) from beam to F11 E detector
~10-15cm Pb bricks were placed within BRIKEN (CH2)n stack to stop heavy particles
1.8.W spectra 20us FSR - see attachments 9 & 10
09.33 DAQ stop - file Oct18/R12_117
All Oct18/R12_* files deleted
09.34 all spectra zero'd
DAQ start - file Oct18/R13
alpha background run
all FEE64 good events statistics OK - see attachment 11
15.11 DAQ continues ok, on file Oct18/R13_2 (alpha run)
system wide checks ok, except nnaida7 failing ADC calibration
FEE64 temperatures ok (attachment 13)
detector bias and leakage currents ok (attachment 14)
good event statistics ok, except nnaida2 due to one hot channel (attachment 15)
Merger and TapeServer ok, no errors in terminal
15.20 DAQ stop - file Oct18/R13_2
15.24 Lowered slow comparator threshold from 100 to 10
good event statistics ok (attachment 16)
15.42 took waveforms, triggering ok (attachment 17)
raised slow comparator threshold to 100 from 10
start DAQ (R14)
nnaida22, no statistics showing (see attachment 18)
subsequent failure to connect to nnaida2
16:44 fixed by rebooting nnaida2 *only*, nnaida2 reset, setup all FEE64s
slow comparator threshold re-raised from 10 to 100, as default was restored
DAQ and alpha run restarted (R15)
Merger and TapeServer ok, no errors in terminal
good event statistics all ok, except for nnaida2 hot channel (attachment 19)
|
|