 Sun Jun 2 04:00:50 2019, TD, Sunday 2 June 21x
|
12.00 DAQ continues file May19/R15_169
ASIC settings 2019May19-17.54.03
slow comparator 0xa
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachments 4
10x <20k, 19x <50k, 24x <100k - same as yesterday evening
Merger OK - see attachment 5
TapeServer OK - see attachment 6
nnaida13 1.*.L spectra - attachment 7 - some evidence of light ions (5 < E < 20MeV) but low rate
FEE64 Rate spectra - attachment 8
1.8.L spectra - see attachments 9 & 10
nnaida1 75 ch FWHM, nnaida3 76 ch FWHM - cf. 77 & 82 ch FWHM respectively yesterday afternoon
p+n FEE64s 1.8.W spectra 20us FSR - attachment 11
n+n FEE64s 1.8.W spectra 20us FSR - attachment 12
Check ASIC Control *all* FEE64s & ASICs
12.20 Offline analysis from R15_0 to R15_167 ADC & disc data synchronisedfor file R15_0 - attachments 13, 14 & 15
18.27 DAQ stop file May19/R15_245
DAQ start - no storage
DAQ stall - reboot all FEE64s *except* nnaida4, 7, 8, 14, 15 & 16 - N.B. no power cycle required
all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 19 & 20
FEE64 temperatures OK - see attachment 21
good event statistics OK - see attachments 16
8x <20k, 15x <50k, 21x <100k - cf. earlier today 10x <20k, 19x <50k, 24x <100k
p+n FEE64s 1.8.W spectra 20us FSR - attachment 17
n+n FEE64s 1.8.W spectra 20us FSR - attachment 18 |
|
Sat Apr 1 16:16:05 2017, OH, CG, Sunday 2 April
|
00:12 BigRips started run 0223 (Started at 00:12)
AIDA file R20_344
System wide checks all ok
BRIKEN start run 67
01.38 Beam stopped to F11. ~1/2 way through R20_364.
01.43 Beam returned to F11. 1GB through R20_366.
BigRIPS file 0224.
BRIKEN run 68.
System-wise checks all ok, except nnaida1 global clocks failed 6.
Temps ok. Leakage currents ok (see attachment 1).
02.43 BigRIPS started run 0225. Start of R20_381
02.48 BRIKEN run 69 started. Start of R20_382.
03.28 System-wide checks same as previous. (R20_391)
03.43 BigRIPS file 0226. ~1/2 way through R20_394
03.48 BRIKEN run 70 started.
04.46 BigRIPS file 0227 started. End of R20_410.
04.48 BRIKEN run 71 started. Start of R20_411.
05.31 36Ne setting is over. End of R20_421.
BigRIPS team is changing setting for calibration. No beam will go through Zerodegree
05.51 R20 stopped (I was getting food).
06.30 20mm Al degrader + 3mm plastic removed from F8. 23mm Al degrader placed at F11 after IC.
06.35 BigRIPS file 0237 started - 38Mg setting.
06.37 R21 started on 38Mg setting.
06.57 Beam stopped to F11 - accelerator problem.
~700MB into R21_5.
Returned shortly after.
07.23 BigRIPS file 0245 started. ~3/4 way through R21_10.
07.26 BigRIPS file 0246 started. ~1/2 way through R21_11.
07.32 BigRIPS file 0247 started. Start of R21_13.
07.34 BigRIPS file 0248 started. ~1/2 way through R21_13.
07.38 BigRIPS file 0249 started. ~1GB into R21_15.
07.40 BigRIPS file 0250 started. Start of R21_16.
07.41 BigRIPS file 0251 started. Little way through R21_16.
08.06 38Mg setting finished. R21 stopped.
08.08 R22 started - got a bit trigger happy with the DAQ. No beam to F11.
08.10 Degrader set to 10mm Al.
08.16 BigRIPS file 0252 started on 39Al setting.
08.17 R23 started on 39Al setting.
08.20 R23 ended.
08.26 40Si setting. Too high rate for AIDA so beam won't be sent down ZDS.
08.40 F11 degrader set to 15mm Al fixed + 4mm Al variable (all in).
08.43 2nd run at 39Al setting.
BigRIPS file 0254 started.
R24 started.
09.00 R24_4 closed. May have been issues with degrader - not sure we were implanting in AIDA...
End of experiment!
09.07 AIDA background run started - R25.
Pulser is on in the run though.
09.20 R25 ended.
BigRIPS run summary attached. |
|
Sun Jul 1 02:26:50 2018, OH, Sunday 1st July
|
10:25 Bias and leakage currents ok - attachment 1
FEE Temperatures ok
System wide checks ok
Alpha run R9 stopped on file R9_74 |
|
Sun Nov 19 01:46:10 2017, CB, TD, Sunday 19 November 14x
|
10.45 Detector biases & leakage currents OK - see attachments 1
FEE64 Temperatures OK - see attachment 2
DAQ statistics OK - note *all* slow comparators 0xa - see attachment 3
7x FEE64s <10k
4x FEE64s 10-20k
4x FEE64s 20-30k
4x FEE64s 30-40k
1x FEE64s 40-50k
4x FEE64 >50k
*all* system wide checks OK *except* nnaida7 fails ADC calibration
14.05 *all spectra zero'd
14.24 Detector biases & leakage currents OK - see attachments 4 & 5
FEE64 Temperatures OK - see attachment 6
DAQ statistics OK - see attachment 7
7x FEE64s <10k
3x FEE64s 10-20k
4x FEE64s 20-30k
5x FEE64s 30-40k
1x FEE64s 40-50k
4x FEE64 >50k
*all* system wide checks OK *except* nnaida7 fails ADC calibration
per FEE64 rate, 1.8.L and 1.8.W spectra (20ms FSR) - see attachments 8-13
14.48 MONLOCK monitor - see attachment 14 |
|
Sun May 19 02:28:07 2019, OH, TD, CA, Sunday 19 May 11x
|
10:28 DAQ Continues ok
Alpha run continues - Currently on file R7_5
System wide checks all ok
leakage currents are up from yesterday - attachment 1
Temperature is up 2 deg C from yesterday which explains leakage current increase
Temp +26.6 deg C, Humidity 28.8% AND D.P +7.2 deg C
FEE Temperatures ok - attachment 2
Good event statistics ok - attachment 3
17.40 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C - water level 75% H-L markers
Temperature +25.4 deg C dew point +7.2 deg C RH 30.9%
17.47 DAQ continues OK to file May19/R7_6
alpha background
ASIC settings 2018Oct03-13.26.58
*except* slow comparator 0xa -> 0x64
BNC PB-4 Pulser OFF
all system wide checks OK *except*
nnaida7 fails ADC calibration
Check SYNC errors not counted since Baseline - see attachment 4 - also failed test following Collect All
SYNC Count Errors for Baseline
N.B. Check SYNC pulses received OK
detector biases & leakage currents OK - see attachments 5 & 6
FEE64 temperatures OK - see attachment 7
good event statistics OK - see attachments 8
Merger OK - see attachment 9
TapeServer OK - see attachment 10
17.53 DAQ stopped file May19/R7_6
DAQ RESET
DAQ SETUP
all system wide checks OK *except* nnaida7 fails ADC calibration
Sync all ASIC clocks using Re-Sync
Check ASIC Control *all* ASICs & FEE64s
17.57 DAQ start file May19/R8
alpha background
ASIC settings 2019May19-17.54.03
slow comparator 0x64
13.13 analysis of May19/R7_6 - see attachment 11
deadtime OK
ADC data for FEE64s nnaida5 & nnaida6 hot channels (Stat spectrum channel # 104)
Also observed at a much lower rate for nnaida1 & nnaida2 |
|
Sun Jun 18 02:56:43 2017, TD, Sunday 18 June 11x
|
10.56 Detector biases & leakage currents OK - see attachments 1 & 2
USB-controlled ac mains relay input #1 fuse blown - replaced
11.12 *all* system wide checks OK *except* nnaida21 fails ADC calibration
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
11.36 nnaida13 & nnaida11 1*W spectra - see attachments 3 & 4
per FEE64 1.8.W spectra - see attachments 5 & 6
good events statistics - see attachment 7
Note c. 3kHz modulated HF noise has disappeared overnight
12.00 2x unused (possibly faulty) MACBs removed from AIDA NIM bins preparatory to UK return
ambient temperature +24.0 deg C, d.p. +8.9 deg C, RH 38.8%
Julabo FL11006 set point +20.0 deg C, actual +20.0 deg C, water level c. 75%
14.03 nnaida13 1*W spectra
Ibias LF feedback 0x8 (default) - see attachments 8 & 10
Ibias LF feedback 0xf - see attachments 9 & 11
14.30 BRIKEN 3He and clovers off
no obvious change in preamp waveform noise
14.33 DSSSD bias off
14.37 FEE64 power off
14.43 2x NIM bins off
BNC PB-4 pulser off
USB-controlled ac mains relay off, interlock enabled, USB cable removed
ac mains circuit off
Tektronix AFG3201C off
Julabo FL11006 off
3ph supply off |
|
Sun Oct 16 03:14:41 2016, TD, Sunday 16 October 16x
|
11.12 DAQ start (R47)
Detector bias and leakage currents OK - see attachments 1 & 2
FEE64 temperatures OK - see attachment 3
Statistics - see attachments 4-14
11.56 Temperature +25.0 deg C, d.p. +8.4 deg C, RH 34.5%
20.33 DAQ found stopped
Most recent file R47_120 (last access 18.26)
R47_120 ADC data synchronised
Restart merger and request DAQ STOP - DAQ stops OK
System-wide tests SYNC errors and SYNC pulses - see attachments 15 & 16 - all other tests OK
DAQ RESET & SETUP OK
Normal restart which failed shortly after enabling ASIC readout - restarting merger did not
recover DAQ control - power cycle required
21.05 DAQ starts (R49)
|
|
Sun Jun 16 04:09:40 2019, CA, CB, ML, TD, CG, Sunday 16 June noon-midnight 16x
|
12.10 DAQ continues OK file RIBF147/R2_145
100Sn setting, no degrader
ASIC settings 2019Jun13-08.56.35
BNC PB-4 Pulser
Amplitude 90,000
x5 attenuator IN
Frequency 25Hz range, variable min. c. 2.5Hz
t_r 100ns, tau_d 50us
- polarity
Delay MIN, tail pulse
good event statistics - DSSSD#1 noisy - see attachment 3
10x <20k, 19x <50k, 20x <100k
p+n FEE64s 1.8.W spectra 20us, 200us, 2ms, 20ms FSR - DSSSD#1 noisy - attachments 4, 6, 7 & 8
n+n FEE64s 1.8.W spectra 20us FSR - DSSSD#1 noisy - attachment 5
FEE64 Rate spectra - attachment 1
Check ASIC Control *all* FEE64s & ASICs x1
FEE64 Rate spectra - attachment 2
Observe that nnaida17 is the really noisy FEE64 - nnaida20, 22 & 23 show increased noise but
not at same level as nnaida17. Is nnaida17 actually the problem? LH kapton PCB is the only
one we did not replace for example.
12.21 DSSSD#1 stats OK
12.36 AIDA R2_151
DTAS run 027
BigRIPS still 2012
13:43 DAQ continues running OK file RIBF147/R2_167
https://www.reddit.com/r/politics/
Settings as before
Good events stats OK - DSSD#1 no longer noisy - see attach 9
Leakage current OK - see attach 10
Systems wide checks OK except nnaida7 fails calibration
Merger ~550k events/second, TapeServer 4435 Kbytes/s
Will increase thresholds on DSSD#1 and decrease on DSSD#3 on next DTAS stop.
14:20 DSSD#1 was found noisy again (Rate>100kHz & Tapeserver 10Mbytes/s)) but then soon after was back to a
normal counting rate (Rate back to ~40kHz & Tapeserver back to 5 Mbytes/s)
14:39 DTAS & BigRIPS stops - changing threshold during AIDA R2_174
DSSD#1 (nnaida17, 20, 22, 23) slow comparator threshold -> 1d (300 keV)
DSSD#3 (nnaida9, 12, 14, 15) slow comparator threshold -> 8 (80 keV)
Check ASIC control x1 on all FEE64
Restarting
AIDA R2_175
DTAS 30
BigRIPS 2013
New stats look OK - zero'd Counters - see attach 11
nnaida 17,20,22,23 rates are down
nnaida 9,12,14,15 rates are up
It appears the data rate balances out. Data items & write to disk similar to before the changes.
See attach 12 & 13
New sample waveforms in attach 14 & 15. nnaida17 looks significantly better than before.
Rates spectra also attached - see 16
17:12 Data rate still ~600k items/s
File rolled over to R2_196
17:30 Current F11 rate ~190 cps
Estimation of implant rate in AIDA of ~270 implants/s (number of HEC events in DSSD1 y strips over duration
of file R2_197)
> increased AIDA rate likely due to double counting of multi-strip events
Temps all ok
18.11 DAQ stats zero'd
*all* histograms zero'd
20:13 DAQ continues to run OK
Data rate ~620k items/s. FEE64 data rates remain approx. same
Temps OK
Just rolled over to file R2_222
20:44 DTAS run 39 started
BigRIPS run 2015
AIDA at 1.2GB into R2_226
22:44 DTAS run 42 started
BigRIPS run 2017
AIDA at 1.3GB into R2_243
Carried out ASIC check successfully
Temps and data rate remain unchanged.
23:16 Been almost 1 day running.
DTAS running out of range in some of their timing histograms so reset the correlation scaler
Reset successfully at start of R2_249
23:19 Reset signal sent again. Still in file R2_249
23:23 DTAS run 43 started
BigRIPS run 2018
AIDA run R2_250
23:54 MIDASSORT spectra saved to /homes/npg/spectra/specs-2019Jun16-23.52.55
MIDASORT online started. |
|
Sat Jun 15 16:53:22 2019, CB, OH, DK, ML, Sunday 16 June 37x
|
00.30 AIDA file R2_26
DTAS run 007
BigRIPS run 2006
00:55
Merger status - attachment 1
TapeSever status - attachment 2
01:40
Before zeroing stats - attachment 3
Histos up to now saved in /homes/npg/spectra/specs-2019Jun16-01.46.50
Before zeroing histos - XY attachment 4
02:22 Up to AIDA R2_41
Stats - attachment 5
XY implants - attachment 6
02:29 AIDA R2_42
DTAS run 011
BigRIPS still 2006
04:08 Up to AIDA R2_55
Temps - attachment 7
Biases - attachment 8
Stats - attachment 9
XY implants - attachment 10
04:50 Did some major UI updates to merger /data02/2019data/dtas/scripts/parallelscript/runall_xe19_dev.sh
If no parameters are passed, it asks to select each option one-by-one, showing available options
For DTAS, if there is only one run for a given header, it automatically selects it
After that, it checks that all the raw files actually exist
Finally, it composes the command, asks the user if it looks OK, and then launches the script (or quits)
(For experts, it can still take the original case where all 7 parameters are passed at the command line)
There may still be some minor bugs, so for now we don't replace the original one until Alvaro can check
06:09 Stats - attachment 11
XY implant profiles -- attachment 12
06:30 DTAS 018; AIDA R2_80; BigRIPS 2009
Things getting a bit noisier?
Merger - attachment 13
TapeServer - attachment 14
Stats - attachment 15
The FEEs corresponding to DSSSD1 are all showing factors 2 to 10 higher than just 30 min. ago
F11 rates still near 180 cps, primary beam still around 130 pnA.
06:43 Before I can diagnose the high noise problem in DSSSD1, it goes back to normal
Merger - attachment 16
TapeServer - attachment 17
Stats - attachment 18
Maybe the issue was from looking at the details too often :)
07:46 Shift change.
DAQ continues running OK.
Statistics show noisy DSSD #1 (100-200kHz) - see attach 19
Tapeserver also shows higher than normal write to disk rate - see attach 20
After a few seconds write to disk rate goes back to normal - see attach 21
Data items rate looks OK (500k). This was checked after the rates in DSSD#1 went back to normal - see attach 22
FEE64 temperatures OK - see attach 23
Implants look OK - see attach 24
System-wide checks OK except nnaida7 fails ADC calibration as usual.
Reset Statistics
Stats now OK - see attach 25
Reset HEC implants
Timewarp events appear to be very frequent, consistently every 3-5 seconds.
This seems to have been happening ever since beam was put on target.
Analysed R2_94 using analyser in Desktop 3. No timewarps reported. See attach 26.
08:32 AIDA: R2_100,
DTAS: 21 ,
BigRips: 2010
08:41 Another noise spike from DSSD#1
Observed up to 1,600k data items per second - see attach 27
Write to disk ~10 MB/s as before.
See LEC xy plot - attach 28
HEC xy plot shows no hints of issues - see attach 29
Rate seems manageable - see attach 30 for analysis of noisy run R2_103.
Note few seconds deadtime in some FEE64 and unequal number of Pause/Resume in nnaida 22
09:45 Rate in DSSD#1 back to normal. Data rate 500k, Write to disk 5 Mb/s.
10:00 Started compressing R2_* files to save disk space.
Used nice gzip to compress to avoid conflicts with the DAQ.
Status of compression can be checked in ELOG desktop in the terminal window running ls -alth
10:32 DTAS and BigRIPS stop runs
AIDA on file R2_128
DTAS:24
BigRIPS 2011
10:56 Lost beam. BigRIPS and DTAS DAQs continue running. Accelerator operators advise beam should be back in 10 minutes.
11:12 Beam is back. BigRIPS & DTAS continue running and did not stop. AIDA file R2_133.
11:25 System-wide checks OK except nnaida7 fails ADC calibration as usual.
Stats OK, but nnaida19 is a bit more noisy than befor (80k) - see attach 31
Temperatures OK - see attach 32
TapeServer & Merger OK - see attach 33, 34 - rates have been low since 10 am
HEC xy plot OK - see attach 35
Reset online spectra
Leakage current OK - attach 36
|
|
Sun Jul 16 14:20:31 2023, TD, Sunday 16 July contd. 27x
|
15.20 All ERNI pins of aida01 adaptor PCB OK => FEE64 #1 ASIC #2 channel #5 issue faulty test C? faulty ASIC channel?
Fitted drain wire from aida06 & aida08 adaptor PCBs to FEE64 cooling plates
n+n FEE64 1.8.W spectra 20us FSR - attachments 1-2
p+n FEE64 1.8.W spectra 20us FSR - attachments 3
p+n FEE64 1.8.L spectra - attachment 4
aida01 1.8.L pulser peak width 15 ch FWHM
n+n FEE64 1.8.L spectra - attachment 5
double peak spectra
Significant improvement in noise for aida06 & aida08 but still not as good as aida02 & aida04. Some additional extrinsic noise observed for aida02 & aida04.
No change in 1.8.L spectra
n+n FEE64 1.8.W spectra aida02 200us FSR, other FEE64s 20us FSR - attachments 6
baseline sinusoid observed - 4T = 320 samples = 64us = 15.6kHz
15:50 BNC PB-5
switch polarity + to -
switch BNC cables from BNC PB-5 and EG&G Ortec 534 outputs for test +/-
Attachments 7-8
baseline sinusoid observed for p+n *not* n+n FEE64 1.8.W spectra
suggests issue is EG&G Ortec 534
Restore original cabling
16.55 Swap aida09 HDMI cable from MACB #4 port 1 to MACB #5 port 1 - power cycle and restart - no change - aida09 clock not locked
Replace aida09 HDMI with *new* HDMI cable to MACB # 4 port 1 - power cycle and restart - aida09 clock locked
FEE64 temperatures OK - attachment 9
System wide checks - attachments 10-15
OK *except* cannot calibrate aida12 ADCs
per FEE64 rate spectra - attachment 16
p+n FEE64 1.8.L spectra - attachments 17
aida01 1.8.L pulser peak width 15 ch FWHM
n+n FEE64 1.8.L spectra - attachments 18
double peak spectra
p+n FEE64 1.8.W spectra 20us FSR - attachments 19-20
n+n FEE64 1.8.W spectra 20us FSR - attachments 21-22
17.10 n+n FEE64 1.8.W spectra 200us FSR
BNC PB-5 decay time 50us - attachment 23
BNC PB-5 decay time 1ms - attachment 24
18.05 ADC data item stats
slow comparator 0x64 -> 0xa
BNC PB-5 pulser frequency 100Hz so expect rate of ADC data items per FEE64 to be c. 6.4kHz
attachment 25 - aida06 & aida08 ground from FEE64 cooling plate to adaptor PCB fitted, test - connected to aida02, aida04, aida06 & aida08
attachment 26 - aida06 & aida08 ground from FEE64 cooling plate to adaptor PCB fitted, test - disconnected from aida02, aida04, aida06 & aida08
attachment 27 - aida06 & aida08 ground from FEE64 cooling plate to adaptor PCB not fitted, test - disconnected from aida02, aida04, aida06 & aida08
Rev A adaptors require grounding (as expected). Output of EG&G Ortec 534 produces c. 15kHz sinsusoid at test input - cable length/capacitative load?
|
|
Sun May 14 01:52:49 2017, TD, OH, Sunday 14 May 16x
|
09.54 DAQ continues OK
Current file May2017/R7_292
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
'good events' statistics OK - see attachment 4
No warnings/errors reported by merger since DAQ GO - see attachment 5
*all* system wide checks OK
10.02 Rate/HitRate spectra - see attachments 6 & 7
1.8.L ADC spectra - see attachments 8 & 9
1.8.W waveforms - see attachments 10-13
10.07 Analysis of data file R7_294 - see attachment 14
dead-time/idle-time < 0.5%
AIDA SYNC100 variations ~330/102000
10.17 E17/F11 ambient temperature +25.1 deg C, RH 37.2%, d.p. +9.4 deg C
Julabo FL11006 set point +20 deg C, actual +20.0 deg C, water level OK (c. 65%)
10.19 DAQ stops OK
Current file May2017/R7_298
Files May2017/R7* *deleted*
ASIC settings 2017Mar27-16.12.39 *except*
slow comparator 0x0a
LEC/MEC fast comparator 0xff
BNC PB-4 settings
Amplitude 90,000
x5 attenuator IN
t_r 50ns, tau_d 50us
polarity -
rate 250Hz range
delay MIN, tail pulse
Check ASIC Control x2
Zero all spectra
10.22 DAQ starts
File May2017/R8
Analysis of May2017/R8_3 confirms ADC data synchronisation - see attachments 15 & 16 |
|
Mon May 13 03:43:08 2019, CA, TD, OH, Sunday 12 May 14x
|
19.12 all system wide checks OK *except* nnaida7 fails ADC calibration
FEE64 temperatures OK - see attachment 9
detector biases & leakage currents OK - see attachments 10 & 11
good event statistics OK - see attachment 12
all FEE64s <100k, 10x < 20k
1.8.W spectra 20us FSR - see attachments 13 & 14 |
|
Sun Jun 12 03:05:37 2016, TD, AE, CG, MA, Sunday 12 June 2016 part 2 11x
|
BigRIPS switched from 60Ti to 64V
AIDA48 (AIDA)2034 (EURICA) 2153 (BigRIPS)
start 08.44
stop 09.08 (FEE64 synchronisation lost -> power cycle & reboot FEE64s)
AIDA49 (AIDA) 2036 (EURICA) 2154 (BigRIPS)
Power cycle and reboot FEE64s
FADC power down (per PJCS recommendation)
All FEE64s pass all system wide checks *except* nnaida16 which failed the ADC calibration (not significant
as waveforms are disabled and FADC powered down anyway)
start 09.30
stop 09.58
ASIC settings 2016Jun12-09.09.37
AIDA50 (AIDA) 2037(EURICA) 2155 (BigRIPS)
start 10.02
stop 10.09 (beam lost)
ASIC settings 2016Jun12-10.10.08
changes to nnaida15 discriminator settings to reduce deadtime (pause-resume rate)
AIDA51 (AIDA) 2038 (EURICA) 2156 (BigRIPS)
start 10.45
stop 11.55
ASIC settings 2016Jun12-10.10.08
aidas1> ~/td/GREAT/analyser2 /TapeData/NP1512/AIDA51_0
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 163625493 ( 974305.9 Hz)
Other data format: 97494507 ( 580529.8 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 1227 ( 7.3 Hz)
RESUME: 1227 ( 7.3 Hz)
SYNC100: 64065 ( 381.5 Hz)
FEE64 disc: 96631002 ( 575388.1 Hz)
MBS info: 796986 ( 4745.6 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 213982 ( 1274.2 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 167.941 s
FEE module #: 1 elapsed dead time 0.142 s
FEE module #: 2 elapsed dead time 1.125 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.307 s
FEE module #: 6 elapsed dead time 0.579 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.082 s
FEE module #: 10 elapsed dead time 0.112 s
FEE module #: 11 elapsed dead time 3.204 s
FEE module #: 12 elapsed dead time 0.005 s
FEE module #: 13 elapsed dead time 0.212 s
FEE module #: 14 elapsed dead time 0.426 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.046 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.064 s
FEE module #: 21 elapsed dead time 0.319 s
FEE module #: 22 elapsed dead time 0.248 s
FEE module #: 23 elapsed dead time 0.010 s
FEE module #: 24 elapsed dead time 0.190 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 60.988s ( 524.691 blocks/s, 32.793 Mb/s)
See attachments 1-7 for AIDA51 rates etc
See attachment 8 for FEE64 synchronisation check (file AIDA51_0) - OK
AIDA52 (AIDA) 2039 (EURICA) 2158 (BigRIPS)
Start 11.56
Stop 12.54 (AIDA FEE lose sync)
Settings file 2016Jun12-10.10.08
Checked correlation of FEEs in file AIDA52_0 at 12.06 and everything seems ok.
aidas1> ~/td/GREAT/analyser2 /TapeData/NP1512/AIDA52_9
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 163879044 ( 985540.7 Hz)
Other data format: 97240956 ( 584790.6 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 1315 ( 7.9 Hz)
RESUME: 1315 ( 7.9 Hz)
SYNC100: 63433 ( 381.5 Hz)
FEE64 disc: 96378426 ( 579603.4 Hz)
MBS info: 796467 ( 4789.8 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 215707 ( 1297.2 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 1 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 166.283 s
FEE module #: 1 elapsed dead time 0.088 s
FEE module #: 2 elapsed dead time 0.724 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.510 s
FEE module #: 6 elapsed dead time 1.337 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.087 s
FEE module #: 10 elapsed dead time 0.121 s
FEE module #: 11 elapsed dead time 2.706 s
FEE module #: 12 elapsed dead time 0.000 s
FEE module #: 13 elapsed dead time 0.127 s
FEE module #: 14 elapsed dead time 0.191 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.058 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.071 s
FEE module #: 21 elapsed dead time 0.399 s
FEE module #: 22 elapsed dead time 0.222 s
FEE module #: 23 elapsed dead time 0.015 s
FEE module #: 24 elapsed dead time 0.061 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 47.215s ( 677.753 blocks/s, 42.360 Mb/s)
12.20 FEE64 temperatures - see attachment 9
Note with all FADC powered off all temperatures now green cf. attachment 8 https://elog.ph.ed.ac.uk/AIDA/305
Julabo FL11006 set point +17 deg C (B3F ambient temperature +25.1 deg C, d.p. +11.2 deg C, RH 40.3%)
13.11 AIDA52_13 per FEE64 ADC timestamp activity OK
12.54 AIDA FEE64 lose synchronisation
No change in system-wide checks
AIDA53 (AIDA) 2040 (EURICA) 2159 (BigRIPS)
Power cycled and rebooted FEE64s
System-wide checks all OK except 6 failures for ADC calibration - not retried
Start 13.09
Stop 13.44 (stop to reset EURICA VME crate)
ASIC Settings file 2016Jun12-10.10.08
13.17 AIDA53_0 FEE64 sync check - OK
aidas1> ~/td/GREAT/analyser2 /TapeData/NP1512/AIDA53_0
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 167386044 ( 1100597.1 Hz)
Other data format: 93733956 ( 616319.7 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 714 ( 4.7 Hz)
RESUME: 714 ( 4.7 Hz)
SYNC100: 58017 ( 381.5 Hz)
FEE64 disc: 92936706 ( 611077.6 Hz)
MBS info: 737805 ( 4851.2 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 166106 ( 1092.2 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 1 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 152.087 s
FEE module #: 1 elapsed dead time 0.020 s
FEE module #: 2 elapsed dead time 0.209 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.107 s
FEE module #: 6 elapsed dead time 0.824 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.008 s
FEE module #: 9 elapsed dead time 0.003 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.378 s
FEE module #: 12 elapsed dead time 0.017 s
FEE module #: 13 elapsed dead time 0.000 s
FEE module #: 14 elapsed dead time 0.059 s
FEE module #: 15 elapsed dead time 0.172 s
FEE module #: 16 elapsed dead time 1.101 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.018 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.093 s
FEE module #: 21 elapsed dead time 0.216 s
FEE module #: 22 elapsed dead time 0.161 s
FEE module #: 23 elapsed dead time 0.665 s
FEE module #: 24 elapsed dead time 0.201 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 25.180s ( 1270.866 blocks/s, 79.429 Mb/s)
AIDA54 (AIDA) 2041 (EURICA) 2160 (BigRIPS)
Start 13.46
Stop 13.53 (loss of sync AIDA54_0)
ASIC Settings file 2016Jun12-10.10.08
System-wide checks OK following loss of sync
19:25
Stable operation most of the afternoon through multiple DAQ start/stops.
FEEs remained synchronised throughout.
SYNCs lost in run AIDA57_37 leading to run stop/start.
-> in AIDA57_37 noticed relatively large chunks of data lost in nnaida6. (see attachments 10+11
19.40 Cumulative pause-resume time for AIDA57_37 (see above) and most recent
complete data file. The pause-resume times are relatively large compared to
other FEE64s but low relative to the measurement time. But we should remember
that we have observed periods of inactivity not bounded by pause-resume tags.
aidas1> ./analyser2 /TapeData/NP1512/AIDA57_37
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 164401851 ( 929891.0 Hz)
Other data format: 96718149 ( 547057.9 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 1081 ( 6.1 Hz)
RESUME: 1081 ( 6.1 Hz)
SYNC100: 67440 ( 381.5 Hz)
FEE64 disc: 95842999 ( 542107.9 Hz)
MBS info: 805548 ( 4556.3 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 194112 ( 1097.9 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 176.797 s
FEE module #: 1 elapsed dead time 0.149 s
FEE module #: 2 elapsed dead time 0.741 s
FEE module #: 3 elapsed dead time 0.004 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.425 s
FEE module #: 6 elapsed dead time 1.697 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.118 s
FEE module #: 10 elapsed dead time 0.084 s
FEE module #: 11 elapsed dead time 1.064 s
FEE module #: 12 elapsed dead time 0.014 s
FEE module #: 13 elapsed dead time 0.063 s
FEE module #: 14 elapsed dead time 0.267 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.010 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.059 s
FEE module #: 21 elapsed dead time 0.125 s
FEE module #: 22 elapsed dead time 0.225 s
FEE module #: 23 elapsed dead time 0.000 s
FEE module #: 24 elapsed dead time 0.205 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 23.047s ( 1388.475 blocks/s, 86.780 Mb/s)
aidas1> ./analyser2 /TapeData/NP1512/AIDA58_6
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ADC data: block: 14849 ptr: 14685 data: 0xC40181C9 module: 16 fail: 0 range: 0 id: 1025 channel:
1 adc: 33225 ts: 0x01AB000000A0 OLD: ts: 0x01AB1000003E tag: 3 type: 0
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 160685457 ( 937303.1 Hz)
Other data format: 100434543 ( 585850.2 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 1282 ( 7.5 Hz)
RESUME: 1282 ( 7.5 Hz)
SYNC100: 65397 ( 381.5 Hz)
FEE64 disc: 99536560 ( 580612.1 Hz)
MBS info: 830022 ( 4841.6 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 213213 ( 1243.7 Hz)
Timewarps: ADC: 1 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 171.434 s
FEE module #: 1 elapsed dead time 0.091 s
FEE module #: 2 elapsed dead time 0.870 s
FEE module #: 3 elapsed dead time 0.000 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.107 s
FEE module #: 6 elapsed dead time 0.518 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.058 s
FEE module #: 10 elapsed dead time 0.095 s
FEE module #: 11 elapsed dead time 2.397 s
FEE module #: 12 elapsed dead time 0.055 s
FEE module #: 13 elapsed dead time 0.157 s
FEE module #: 14 elapsed dead time 0.238 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.000 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.013 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.174 s
FEE module #: 21 elapsed dead time 0.298 s
FEE module #: 22 elapsed dead time 0.280 s
FEE module #: 23 elapsed dead time 0.004 s
FEE module #: 24 elapsed dead time 0.071 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 18.234s ( 1754.927 blocks/s, 109.683 Mb/s) |
|
Sat Jun 11 17:24:11 2016, DK, TD, Sunday 12 June 2016 14x
|
Runs 41 and 42 are quite short. Run 41 was interrupted by the beam dropping (operators called), and run 42 we are just trying to get EURICA to synchronize with AIDA DAQ.
1:08 Started AIDA Run 43 for 60Ti beam (EURICA run 2027; BigRIPS run 2132; CAEN Run 3018)
Leak currents less than 5 uA. See attachments 1 & 2
Scalers are shown as attachment 3
FEEE synchronization with pulser signal is shown as attachment 4
1:21 operator calls to note that the beam is stopped.
1:25 started AIDA run 44 for 60Ti beam (EURICA run 2028; BigRIPS #2133; CAEN #3019)
1:31 stopped because CAEN DAQ goes down.
1:34 started AIDA run 45 for 60Ti beam (EURICA run 2029; BigRIPS #2134; CAEN #3020)
1:37 data stops writing to disk for AIDA for unknown reason.
1:50 nnaida11 showed no SYNCs. Stop / GO on Run Control resolves it.
but 18 is off for the merger link. was this the status quo? try to reboot the merger but everything gets upset.
my first power cycle alone! (daid)
load the settings file 2016Jun10-20.30.18 which seems to be the most recent one
it takes some time, but finally I can get things up and running it seems.
2:40 still 18 link is down. strange. hopefully it's an acceptable loss, because I think it has been a long day for everyone.
OH DUH! nnaida19 hasn't been working for the entire experiment!! Just I forgot on the merge links it is offset 0 and not offset 1 for counting.
I could get some practice restoring AIDA at least?
Anyway, there had been some problems from run 45, and now all is well.
2:40 AIDA run 46. It's just a test that the system is working. But I forgot to put the TapeServer Volume Name so who knows where it ended up (discarded to /dev/null ?)
2:42 AIDA run 47, started with EURICA up and ready. (BigRIPS #2137; EUIRCA #2032; CAEN #3023)
Basically everything looks reasonable I think
SSD XY pattern looks basically okay. See attachment
Pulser shows the FEEs are synchronized nicely. See attachment 6
Biases and leak currents are shown in attachments 7 and 8
Scalers are shown as attachment 9
Check the pause/resumes. From the html Statistics page, nnaida20 shows some pauses, while nnaida24 seems to pause regularly.
I use Tom's program as outlined in a previous elog. He said we shall want the elapsed dead time to be much less than the timestamp elapsed
~/td/GREAT/analyser2 /TapeData/NP1512/AIDA47_26
*** GREAT format 3.2.0 analyser - TD - May 2014
*** FEE64 discriminator: block: 23312 ptr: 2071 data: 0x98638000 module: 24 information type: 6 information field: 0x00038000 ts: 0x0083500000A0 OLD: ts: 0x00836000009F tag: 2 type: 6
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 140888182 ( 963280.2 Hz)
Other data format: 120231818 ( 822048.6 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 4747 ( 32.5 Hz)
RESUME: 4747 ( 32.5 Hz)
SYNC100: 55794 ( 381.5 Hz)
FEE64 disc: 119436810 ( 816612.9 Hz)
MBS info: 729720 ( 4989.2 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 286072 ( 1955.9 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 0 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 1 ( 0.0 Hz)
FEE64 disc: 1 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 146.259 s
FEE module #: 1 elapsed dead time 0.019 s
FEE module #: 2 elapsed dead time 0.232 s
FEE module #: 3 elapsed dead time 0.002 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.255 s
FEE module #: 6 elapsed dead time 0.215 s
FEE module #: 7 elapsed dead time 0.001 s
FEE module #: 8 elapsed dead time 0.000 s
FEE module #: 9 elapsed dead time 0.028 s
FEE module #: 10 elapsed dead time 0.000 s
FEE module #: 11 elapsed dead time 0.036 s
FEE module #: 12 elapsed dead time 0.089 s
FEE module #: 13 elapsed dead time 0.001 s
FEE module #: 14 elapsed dead time 0.034 s
FEE module #: 15 elapsed dead time 0.000 s
FEE module #: 16 elapsed dead time 0.478 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.077 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.166 s
FEE module #: 21 elapsed dead time 0.760 s
FEE module #: 22 elapsed dead time 0.029 s
FEE module #: 23 elapsed dead time 0.755 s
FEE module #: 24 elapsed dead time 0.448 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
It could be around 5% total, but I do not think it is so terrible.
4:56 AIDA Run 47_53 begins 4:56. We do not restart the runs. EURICA also automatically had the new run 2033 at 4:56. BigRIPS manually stop / start is now at 2138 (4:57). CAEN run is still 3023.
5:02: At start of run, the beam dropped
5:05 PPAC F3 1A trips.
Leak current shown as attachment 10 and 11
Scalers shown as attachment 12
FEE sync looks good, as well as SSD XY. About 370 MB of ROOT tree (compared to typical check of 50 MB) Attachments 13 and 14, respectively.
Here are Tom's pause information
aidas1> ~/td/GREAT/analyser2 /TapeData/NP1512/AIDA47_53
*** GREAT format 3.2.0 analyser - TD - May 2014
*** ERROR: READ I/O error: 5002
blocks: 32000
ADC data format: 146454667 ( 944617.0 Hz)
Other data format: 114665333 ( 739579.2 Hz)
Sample trace data format: 0 ( 0.0 Hz)
Undefined format: 0 ( 0.0 Hz)
Other data format type: PAUSE: 4216 ( 27.2 Hz)
RESUME: 4216 ( 27.2 Hz)
SYNC100: 59144 ( 381.5 Hz)
FEE64 disc: 113857390 ( 734368.1 Hz)
MBS info: 740367 ( 4775.3 Hz)
Other info: 0 ( 0.0 Hz)
ADC data range bit set: 272434 ( 1757.2 Hz)
Timewarps: ADC: 0 ( 0.0 Hz)
PAUSE: 1 ( 0.0 Hz)
RESUME: 0 ( 0.0 Hz)
SYNC100: 0 ( 0.0 Hz)
FEE64 disc: 0 ( 0.0 Hz)
MBS info: 0 ( 0.0 Hz)
Undefined: 0 ( 0.0 Hz)
Sample trace: 0 ( 0.0 Hz)
Timestamp elapsed time: 155.041 s
FEE module #: 1 elapsed dead time 0.014 s
FEE module #: 2 elapsed dead time 0.231 s
FEE module #: 3 elapsed dead time 0.005 s
FEE module #: 4 elapsed dead time 0.000 s
FEE module #: 5 elapsed dead time 0.220 s
FEE module #: 6 elapsed dead time 0.040 s
FEE module #: 7 elapsed dead time 0.000 s
FEE module #: 8 elapsed dead time 0.009 s
FEE module #: 9 elapsed dead time 0.043 s
FEE module #: 10 elapsed dead time 0.005 s
FEE module #: 11 elapsed dead time 0.064 s
FEE module #: 12 elapsed dead time 0.006 s
FEE module #: 13 elapsed dead time 0.008 s
FEE module #: 14 elapsed dead time 0.039 s
FEE module #: 15 elapsed dead time 0.065 s
FEE module #: 16 elapsed dead time 0.457 s
FEE module #: 17 elapsed dead time 0.000 s
FEE module #: 18 elapsed dead time 0.015 s
FEE module #: 19 elapsed dead time 0.000 s
FEE module #: 20 elapsed dead time 0.059 s
FEE module #: 21 elapsed dead time 0.330 s
FEE module #: 22 elapsed dead time 0.043 s
FEE module #: 23 elapsed dead time 0.989 s
FEE module #: 24 elapsed dead time 0.462 s
FEE module #: 25 elapsed dead time 0.000 s
FEE module #: 26 elapsed dead time 0.000 s
FEE module #: 27 elapsed dead time 0.000 s
FEE module #: 28 elapsed dead time 0.000 s
FEE module #: 29 elapsed dead time 0.000 s
FEE module #: 30 elapsed dead time 0.000 s
FEE module #: 31 elapsed dead time 0.000 s
FEE module #: 32 elapsed dead time 0.000 s
*** Program elapsed time: 21.295s ( 1502.706 blocks/s, 93.919 Mb/s)
|
|
Sat Nov 10 21:53:29 2018, CA, CB, TD, OH, Sunday 11 November 21x
|
06.53 DAQ continues OK - data transfer disabled
06.55 all system wide checks OK *except* nnaida7 fails ADC calibration
detector biases & leakage currents OK - see attachments 1 & 2
Julabo FL11006 chiller set point +20 deg C actual +20 deg C, water level c. 75% (L-H)
ambient tempature + 26.9 deg C, RH 21.6%, d.p. +2.9 deg C
FEE64 temperatures OK - see attachment 3
good event statistics OK - see attachment 4
per FEE64 rate spectra - see attachment 5
ASIC check load
per FEE64 rate spectra - see attachment 6
good event statistics OK - see attachment 7
1.8.L spectra - see attachments 8 & 9
nnaida1 pulser peak width 72 ch FWHM
1.8.W spectra 20us FSR - see attachments 10 & 14
1.8.W spectra 200us FSR - see attachments 11 & 15
1.8.W spectra 2ms FSR - see attachments 12 & 16
1.8.W spectra 20ms FSR - see attachments 13 & 17
Note - LED threshold 9000 for *all* FEE64s
07.27 statistics zero'd
some 32bit counters (e.g. nnaida19 & nnaida20) had overflowed/wrapped around
18:19 Computer appears to be running slow though cannot see a reason why.
No programs using to much ram or cpu
FEE temp ok - attachment 18
bias and leakage currents ok - attachment 19
System wide checks ok
21:02 System wide checks ok
DAQ Continues ok - data transfer disabled.
Bias and leakage currents ok - attachment 20
FEE Temperatures ok - attachment 21 |
|
Sun Jun 11 08:23:23 2017, PV, Sunday 11 June 16:00-00:00 21x
|
16:40 beam lost - stripper foil problem
AIDA file RIBF128/R9_55
16:45 beam is back
AIDA file R9_57
17:19 BRIKEN and BigRIPS stop DAQs
AIDA on file R9_66
17:21 BigRIPS starts run 4024
BRIKEN starts run 134
AIDA on file R9_67
17:24 beam lost
AIDA on file R9_68
17:50 beam is still off
BRIKEN and BigRIPS stop DAQs
AIDA on file R9_74
17.52 Detector biases & leakage currents OK - see attachments 1
FEE64 Temperatures OK - see attachment 2
good events statistics stable (nnaida13 still ~140k) - see attachment 3
Merger and Tape server OK - see attachment 4,5
*all* system wide checks OK except ADC calibration for nnaida13
18:00 beam is back
BRIKEN starts run 135
BigRIPS starts run 4025
AIDA on file R9_76
18:05 analysis of file RIBF128/R9_77 no timewarps, 6 MBS timewarps ~1% dead time on nnaida13 - attachment 6
18:15 beam lost. RF is down.
AIDA on file R9_80
18:19 beam is back
AIDA on file R9_82
19:04 BRIKEN and BigRIPS stop DAQs
AIDA on file R9_93
19:05 BigRIPS starts run 4026
BRIKEN starts run 136
AIDA on file R9_94
19:40 analysis of file RIBF128/R9_102 no timewarps, 1 MBS timewarps - attachment 7
19:44 online high energy hit pattern - attachment 8
AIDA on file R9_104
zeroed Midas sort online histogram
19.50 Detector biases & leakage currents OK - see attachments 9
FEE64 Temperatures OK - see attachment 10
good events statistics stable - see attachment 11
Merger and Tape server OK - see attachment 12, 13
*all* system wide checks OK except ADC calibration for nnaida13
20:05 BRIKEN and BigRIPS stop DAQs
AIDA on file R9_110
20:07 BigRIPS starts run 4027
BRIKEN starts run 137
AIDA on file R9_111
20:11 Accelerator people stop the beam to fix the stripper system for about 30 min.
BRIKEN and BigRIPS stop DAQs
AIDA on file R9_112
21:12 Beam is back
AIDA on file R9_127
21:12 BigRIPS starts run 4028
BRIKEN starts run 138
AIDA on file R9_127
21:21 offline analysis RIBF128/R9_128 rates
*** DSSSD # 1 count: 469757 old count: 409726 dt: 1.01 s LEC rate: 59182.53 Hz
*** DSSSD # 2 count: 688773 old count: 600379 dt: 1.01 s LEC rate: 87144.65 Hz
*** DSSSD # 3 count: 226922 old count: 196673 dt: 1.01 s LEC rate: 29821.47 Hz
*** DSSSD # 4 count: 197996 old count: 173086 dt: 1.01 s LEC rate: 24557.93 Hz
*** DSSSD # 5 count: 75519 old count: 66217 dt: 1.01 s LEC rate: 9170.53 Hz
*** DSSSD # 6 count: 161720 old count: 141631 dt: 1.01 s LEC rate: 19805.07 Hz
*** DSSSD # 1 count: 6 old count: 6 dt: 1.01 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 212 old count: 179 dt: 1.01 s HEC rate: 32.53 Hz
*** DSSSD # 3 count: 54 old count: 49 dt: 1.01 s HEC rate: 4.93 Hz
*** DSSSD # 4 count: 20 old count: 16 dt: 1.01 s HEC rate: 3.94 Hz
*** DSSSD # 5 count: 43 old count: 37 dt: 1.01 s HEC rate: 5.92 Hz
*** DSSSD # 6 count: 117 old count: 105 dt: 1.01 s HEC rate: 11.83 Hz
zeroed Midas sort histograms
21:38 beam lost due to stripper problem
AIDA on file R9_134
21:41 analysis of file RIBF128/R9_134 no timewarps, no MBS timewarps - attachment 14
20:05 BRIKEN and BigRIPS stop DAQs
AIDA on file R9_138
22.00 Detector biases & leakage currents OK - see attachments 15
FEE64 Temperatures OK - see attachment 16
good events statistics OK (no beam now) - see attachment 17
Merger and Tape server OK - see attachment 18, 19
*all* system wide checks OK except ADC calibration for nnaida13
22:09 beam is back
BigRIPS starts run 4029
BRIKEN starts run 139
AIDA on file R9_142
22:42 online implantation profile - attachment 20
AIDA on file R9_151
zeroed Midas sort online histograms
23:10 BRIKEN and BigRIPS stop DAQs
AIDA on file R9_159
23:11 BigRIPS starts run 4030
BRIKEN starts run 140
AIDA on file R9_159
23:37 analysis of file RIBF128/R9_165 no timewarps, 2 MBS timewarps - attachment 21 |
|
Sun Jun 11 00:07:24 2017, OH, Sunday 11 June 08:00-16:00 25x
|
08:10 BRIKEN and BigRIPS stops DAQs
AIDA on file R7_1287
08:11 Beam going for half an hour. Problem with vacuum around RRC
08:24 Beam is back
08:25 BigRIPS starts run 4016
BRIKEN starts run 126
AIDA on file R7_1291
08:32 RF down should be 5 minutes
08:44 Beam back
09:25 RF Down
09:26 BigRIPS and BRIKEN stop DAQs
AIDA on file R7_1306
09:35 Beam back
BigRIPS starts run 4017
BRIKEN starts run 127
AIDA on file R7_1308
09:53 System wide checks all ok
Bias and leakage currents ok - attachment 1
Good events - attachment 2
FEE temperatures - attachment 3
10:29 BRIKEN and BigRIPS stop DAQs
AIDA on file R7_1322
10:31 BigRIPS starts run 4018
BRIKEN starts run 128
AIDA on file R7_1323
11:31 BigRIPS and BRIKEN stop their DAQs
AIDA on file R7_1338
11:32 BigRIPS starts run 4019
BRIKEN starts run 129
AIDA on file R7_1338
11.49 Detector biases & leakage currents OK - see attachments 4 & 5
FEE64 Temperatures OK - see attachment 6
good events statistics stable & OK - see attachment 7
No warnings/errors reported by merger since DAQ GO - see attachment 8
*all* system wide checks OK (zero fails)
11.53 online analysis
per DSSSD x versus y (HEC) - see attachment 9
per DSSSD E_p versus E_n (HEC) - see attachment 10
ADC & disc data synchronised - see attachment 11
11.55 analysis of file RIBF128/R7_1344 - dead time < 0.5%, no timewarps, 1 MBS timewarps - see attachment 12
12.03 offline analysis RIBF128/R7_1346 rates
*** DSSSD # 1 count: 942048 old count: 885423 dt: 1.04 s LEC rate: 54296.31 Hz
*** DSSSD # 2 count: 1402896 old count: 1319759 dt: 1.04 s LEC rate: 79718.00 Hz
*** DSSSD # 3 count: 422965 old count: 397383 dt: 1.04 s LEC rate: 24529.94 Hz
*** DSSSD # 4 count: 356558 old count: 336037 dt: 1.04 s LEC rate: 19677.08 Hz
*** DSSSD # 5 count: 124978 old count: 117233 dt: 1.04 s LEC rate: 7426.49 Hz
*** DSSSD # 6 count: 277397 old count: 260863 dt: 1.04 s LEC rate: 15854.04 Hz
*** DSSSD # 1 count: 6 old count: 6 dt: 1.04 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 150 old count: 139 dt: 1.04 s HEC rate: 10.55 Hz
*** DSSSD # 3 count: 98 old count: 96 dt: 1.04 s HEC rate: 1.92 Hz
*** DSSSD # 4 count: 12 old count: 10 dt: 1.04 s HEC rate: 1.92 Hz
*** DSSSD # 5 count: 36 old count: 33 dt: 1.04 s HEC rate: 2.88 Hz
*** DSSSD # 6 count: 155 old count: 145 dt: 1.04 s HEC rate: 9.59 Hz
all SortSas spectra & histograms zero'd, waveforms set x-range = 1000ch = 2ms
12.04 BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency 25Hz range 2.6Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Mar27-16.12.39
BigRIPS 149Xe setting, F1 slits 51mm, degrader 2mm Al (at F7), 1.3mm Al fixed + 2mm Al variable (at F11)
12.15 layout spectra - see attachments 13-20
12.20 FEE64# 1-16 power fail
AIDA on file R7_1351
12.30 requested beam off, replaced 250V/16A/fast fuse
nnaida13 good events rate ~250k, cycled DSSSD bias reduced to ~140k
13:06 BRIKEN starts run 130
BigRIPS starts run 4020
AIDA on file R9_0
13:07 Ambient Temperature +23.9 - Humidity 29.6% - Dew point +5.1C
Leakage currents and bias ok - attachment 21
Water level in chiller ok
14:06 BigRIPS and BRIKEN stop their daqs
AIDA on file R9_16
14:08 BigRIPS starts run 4021
BRIKEN starts run 131
AIDA on file R9_16
14:31 System wide checks ok
Good events - attachment 22
FEE temperatures - attachment 23
Analysis output for R9_16 - attachment 24
15:10 BRIKEN and BigRIPS stop daqs
AIDA on file R9_32
15:11 BRIKEN starts run 132
BigRIPS starts run 4022
AIDA on R9_32
15:13 Leakage and bias ok - attachment 25
15:30 DSSD Rates from R9_36
*** DSSSD # 1 count: 95157 old count: 45985 dt: 1.03 s LEC rate: 47603.61 Hz
*** DSSSD # 2 count: 153477 old count: 76756 dt: 1.03 s LEC rate: 74273.90 Hz
*** DSSSD # 3 count: 40379 old count: 20036 dt: 1.03 s LEC rate: 19694.14 Hz
*** DSSSD # 4 count: 46339 old count: 23014 dt: 1.03 s LEC rate: 22581.02 Hz
*** DSSSD # 5 count: 14241 old count: 7012 dt: 1.03 s LEC rate: 6998.42 Hz
*** DSSSD # 6 count: 36061 old count: 18008 dt: 1.03 s LEC rate: 17477.18 Hz
*** DSSSD # 1 count: 0 old count: 0 dt: 1.03 s HEC rate: 0.00 Hz
*** DSSSD # 2 count: 16 old count: 8 dt: 1.03 s HEC rate: 7.74 Hz
*** DSSSD # 3 count: 14 old count: 8 dt: 1.03 s HEC rate: 5.81 Hz
*** DSSSD # 4 count: 1 old count: 0 dt: 1.03 s HEC rate: 0.97 Hz
*** DSSSD # 5 count: 4 old count: 1 dt: 1.03 s HEC rate: 2.90 Hz
*** DSSSD # 6 count: 26 old count: 13 dt: 1.03 s HEC rate: 12.59 Hz
16:10 BigRIPS and BRIKEN stop DAQs
AIDA on file R9_47
16:12 BRIKEN starts run 133
BigRIPS starts run 4023
AIDA on file R9_47
16:18 BigRIPS slit is closing
DSSD rates for R9_49
*** DSSSD # 1 count: 121641 old count: 64167 dt: 1.00 s LEC rate: 57287.24 Hz
*** DSSSD # 2 count: 179018 old count: 93277 dt: 1.00 s LEC rate: 85462.38 Hz
*** DSSSD # 3 count: 52138 old count: 28005 dt: 1.00 s LEC rate: 24054.58 Hz
*** DSSSD # 4 count: 53927 old count: 27419 dt: 1.00 s LEC rate: 26421.86 Hz
*** DSSSD # 5 count: 16617 old count: 9291 dt: 1.00 s LEC rate: 7302.19 Hz
*** DSSSD # 6 count: 38751 old count: 19986 dt: 1.00 s LEC rate: 18704.02 Hz
*** DSSSD # 1 count: 1 old count: 0 dt: 1.00 s HEC rate: 1.00 Hz
*** DSSSD # 2 count: 52 old count: 30 dt: 1.00 s HEC rate: 21.93 Hz
*** DSSSD # 3 count: 12 old count: 7 dt: 1.00 s HEC rate: 4.98 Hz
*** DSSSD # 4 count: 3 old count: 3 dt: 1.00 s HEC rate: 0.00 Hz
*** DSSSD # 5 count: 9 old count: 5 dt: 1.00 s HEC rate: 3.99 Hz
*** DSSSD # 6 count: 37 old count: 19 dt: 1.00 s HEC rate: 17.94 Hz |
|
Sun Dec 10 13:06:27 2023, TD, Sunday 10 December 14x
|
14.05 S4 closed
Water flow and temperature ( gauges outside S4 entrance ) OK
BNC PB-5 pulser connected to p+n FEE64s by diasy chain of test + inputs
ASIC settings 2023Nov16-18.55.20
p+n FEE64s slow comparator 0xa, n+n FEE64s 0xf
All system wide checkks OK *except* adia08 ADC calibration failed
DSSSD bias -150V leakage current -5.28uA - OK - attachment 1
FEE64 temperatures OK - attachment 2
ADC data item stats - attachment 3
rates dominated by relatively few 'hot' channels
aida06 - no cables connected to FEE64 adaptor PCB
per FEE64 Rate spectra - attachment 4
aida06 - no cables connected to FEE64 adaptor PCB
system relatively quiet but has been quieter - no grounding of bPlast cabling and PSUs?
p+n and n+n FEE64 1.8.W spectra - 20us FSR - attachments 5-8
aida06 - no cables connected to FEE64 adaptor PCB
aida08 - no ADC calibration
18.25
SSSD bias -150V leakage current -5.100uA - OK - attachment 9
FEE64 temperatures OK - attachment 10
ADC data item stats - no significant change - attachment 11
rates dominated by relatively few 'hot' channels
aida06 - no cables connected to FEE64 adaptor PCB
per FEE64 Rate spectra - no significant change - attachment 12
aida06 - no cables connected to FEE64 adaptor PCB
system relatively quiet but has been quieter - no grounding of bPlast cabling and PSUs?
p+n and n+n FEE64 1.8.W spectra - 20us FSR - attachments 13-14
aida06 - no cables connected to FEE64 adaptor PCB
aida08 - no ADC calibration |
|
Sun Oct 1 12:38:56 2023, TD, Sunday 1 October 13x
|
12.50 Power up
All system wide checks OK
per FEE64 p+n 1.8.W spectra 20us FSR - attachments 3-4
per FEE64 p+n 1,8.L spectra - attachment 6
aida01 pulser peak width 15 ch FWHM
per FEE64 Rate spectra - attachment 5
BNC PB-5 pulser
Amplitude 10.0V
Attenuation x10
Decay 1ms
Frequency 25Hz
Polarity + ( n+n Ohmic test input from EG&G Ortec 534 Sum & Invert Amplifier not connected )
Clamp ON
ASIC settings 2021Apr29-13-16-00
slow comparator 0x64
FEE64 temperatures OK - see attachment 1
ADC data item stats OK - see attachment 2 |
|
Sun Nov 6 01:34:15 2016, TD, OH, CG, Sun 6th November 18x
|
10:34 Detector Bias a leakage currents all ok. (Attachments 1 and 2)
Temperatures all ok (Attachment 3)
All system wide checks ok other than clock status see attachment 4
DAQ continues to run ok (R124) (No stop at 6:30am)
DAQ running at about 14MB/s to disc which is faster than before.
Most likely due to the increased rate in detector 1 which is represented at FEEs 17, 20, 22 and 23 in
attachment 5.
Also attached are the spectra for layouts 1-4 & 7-8 as attachments 6-11
When looking at the pulser spectrum in layouts 3 and 4 (attachments 9 and 10) we see that the pulser peaks
relating to this detector is broader shown by
the decreased peak height.
Comparing the waveforms in attachments 11 and 12 to those taken on Monday 31st Oct we see that the noise
in nnaida 5 and 6 has been greatly reduced.
On the others however there appears to be an increase in the amplitude of the noise.
11:25 The second putty window for leakage currents was found to have been frozen for the past 24 hours.
Was reloaded and updated leakage currents are in attachment 13 and 14
12.15 Analysis of R124_291 shows ADC & disc data synchronised - see attachment 15
Analysis of data file - see attachment 16
18:26 DAQ stopped, presumably during LN2 fill cycle.
Restarted the merger and tried "Stop" on the DAQ control page. ~50% of nnaida now show "error."
R124 closed 18.29
Could not regain control of the system. Jorge switched BRIKEN to its internal clock and FEEs power cycled @
19.20.
23.35 DAQ started (R126 - no storage mode)
DSSSD bias & leakage currents OK - see attachment |
|