12.47 DAQ continues OK to file May19/R7_3

      alpha background

      ASIC settings 2018Oct03-13.26.58
      *except* slow comparator 0xa -> 0x64

      BNC PB-4 Pulser OFF

      all system wide checks OK *except* nnaida7 fails ADC calibration

      detector biases & leakage currents OK - see attachments 1 & 2

      FEE64 temperatures OK - see attachment 3
      good event statistics OK - see attachments 4

      Merger OK - see attachment 5
      TapeServer OK - see attachment 6

12.51 Check ASIC Control *all* ASICs & FEE64s

      1.8.L spectra - see attachments 7 & 8
      p+n FEE64s 1.8.W spectra 20us, 200us, 2ms, 20ms FSR - attachments 9-12
      n+n FEE64s 1.8.W spectra 20us, 200us, 2ms, 20ms FSR - attachments 13-16

13.13 analysis of May19/R7_3 - see attachment 17
      deadtime OK
      ADC data for FEE64s nnaida5 & nnaida6 hot channels (Stat spectrum channel # 104)
      Also observed at a much lower rate for nnaida1 & nnaida2

13.27 Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C - water topped up to H level marker
      Temperature +24.6 deg C dew point +7.1 deg C RH 32.6%

10.18 DAQ continues OK to file May19/R5_1

      alpha background

      ASIC settings 2018Oct03-13.26.58
      *except* slow comparator 0xa -> 0x64

      BNC PB-4 Pulser OFF

      all system wide checks OK *except* nnaida7 fails ADC calibration

      detector biases & leakage currents OK - see attachments 1 & 2

      FEE64 temperatures OK - see attachment 3
      good event statistics OK - see attachments 4

      Merger OK - see attachment 5
      TapeServer OK - see attachment 6

      1.8.W spectra 20us FSR - attachments 7 & 8
      1.8.W spectra 20ms FSR - attachments 9 & 10

      Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C - water topped up
      Temperature +24.8 deg C dew point +8.3 deg C RH 35.3%

10.42 DAQ stop May19/R5_2

      slow comparator 0x64 -> 0xa
      Check ASIC Control *all* ASICs & FEE64s

10:52 AIDA inserted ~4cm into DTAS
      60Co (~40kBq) + 137Cs (~8kBq) sources located approximately 4cm in front of the front face of the snout

10.54 DAQ start May19/R6

      good event statistics OK - see attachments 11
      *all* FEE64s <100k, 9x < 20k
      data rate 4.9Mb/s 0.64M data items/s

11.04 nnaida17 good events c. 350k returns to 13k following Check ASIC Control (nnaida1 OK - see
https://elog.ph.ed.ac.uk/AIDA/801 )
      AIDA disc statistics indicate that fast discriminators were source of higher rate - next time this 
      happens we should check HitRate to see whether this is a specific channel or channels and possibly 
      mask

11.17 DTAS DAQ issues correlation scaler reset 
      AIDA data file May19/R6_3

      use files *from* R6_4

11.39 DAQ stop file May19/R6_8

      nnrpi1 is offline - we suspect wrench or power tool placed too close to RPi when we moved AIDA
      into DTAS and we jostled one or other of the cables connected to nnrpi1

      nnrpi1 power cycled to reboot
      *all* FEE64s OK
      USB ac mains relay controls recovered OK
      CAEN N1419 contrs recovered OK

11.48 AIDA withdrawn from DTAS for installation of upstream (CH2)n shield and additional Pb wall

11.52 DAQ starts to file May19/R7

      alpha background resumes

      ASIC settings 2018Oct03-13.26.58
      *except* slow comparator 0xa -> 0x64

      BNC PB-4 Pulser OFF

18.06 DAQ continues ok, on file May19/R7_0

      all system wide checks OK *except* nnaida7 fails ADC calibration

      detector biases & leakage currents OK - see attachment 13

      FEE64 temperatures OK - see attachment 14
      good event statistics OK - see attachment 15

      Merger and TapeServer ok

      Temperature +25.0 deg C dew point +4.4 deg C RH 27.0%



  

10:13 all system wide checks OK *except* nnaida7 fails ADC calibration

      FEE64 temperatures OK - see attachment 1
      good event statistics OK - see attachments 2

      detector biases & leakage currents OK - see attachment 3

      Temperature + deg 24.7C dew point +8.6 deg C RH 35.0%

      Merger and TapeServer ok

10:30 DAQ, merger, TapeServer stop 

      Alpha run stopped at AIDA file TapeData/May19/R2_5

      slow comparator threshold lowered to 10 keV (0xa)

      DAQ start, not writing to file

      good event statistics after lowering threshold, ok (attachment 4)

10:49 1.8.W spectra 20ms FSR - attachments 5 & 6

11:25 started writing to file R3 (sync test)
      low threshold run at 5mb/s

11:33 DAQ stop (R3)

      slow comparator threshold raised to 100 kev (0x64)

      DAQ start, alpha run

      Writing to file TapeData/May19/R4

18.49 alpha background

      ASIC settings 2018Oct03-13.26.58
      *except* slow comparator 0xa -> 0x64

      BNC PB-4 Pulser OFF

      FEE64 temperatures OK - see attachment 7
      good event statistics - see attachments 8 - nnaida1 405k & nnaida17 368k, all other FEE64s c. 380Hz as
expected
      ASIC check for *all* ASICs & FEE64s restored all FEE64 rates to expected c. 380Hz - see attachment 13

      detector biases & leakage currents OK - see attachments 9 & 10

      Merger OK - no error messages - see attachment 11
      TapeServer OK - see attachment 12

      all system wide checks OK *except* nnaida7 fails ADC calibration *and* Check Sync errors not counted Since
Baseline - see attachment 14

      DAQ stopped May19/R4_3

aidas1> ls -l /TapeData/May19
total 19808048
-rw-rw-rw-. 1 npg npgstaff 1908736000 May 14 18:28 R1_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 02:30 R2_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 10:20 R2_1
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 15 18:08 R2_2
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 01:57 R2_3
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 09:45 R2_4
-rw-rw-rw-. 1 npg npgstaff  190447616 May 16 10:28 R2_5
-rw-rw-rw-. 1 npg npgstaff 1109327872 May 16 11:28 R3_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:39 R4_0
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:45 R4_1
-rw-rw-rw-. 1 npg npgstaff 2097152000 May 16 18:50 R4_2
-rw-rw-rw-. 1 npg npgstaff  225312768 May 16 18:54 R4_3
-rw-rw-rw-. 1 npg npgstaff   52494336 May 16 19:10 R5_0

      Wahtever the issue was it probably occurred before 18.39

      DAQ RESET
      DAQ SETUP
      ASIC check for *all* ASICs & FEE64s
      all system wide checks OK *except* nnaida7 fails ADC calibration
      Sync all ASIC clocks using Re-SYNC

      DAQ started May19/R5

19.23 1.8.W spectra - see attachments 15 & 16

10.18 DAQ continues OK to file May19/R2

      alpha background

      ASIC settings 2018Oct03-13.26.58
      *except* slow comparator 0xa -> 0x64

      BNC PB-4 Pulser OFF

      all system wide checks OK *except* nnaida7 fails ADC calibration

      detector biases & leakage currents OK - see attachments 1 & 2

      FEE64 temperatures OK - see attachment 3
      good event statistics OK - see attachments 4

      Merger OK - see attachment 5
      TapeServer OK - see attachment 6

      1.8.L spectra - attachments 7 & 8
      1.8.W spectra 20us FSR - attachments 10 & 11
      1.8.W spectra 20ms FSR - attachments 10 & 11

      Julabo FL11006 chiller set point +20 deg C actual +20.0 deg C - water topped up
      Temperature + deg 24.7C dew point +7.5 deg C RH 33.3%

      FEE64 nnaida1-4 temperature logs - see attachments 12-15
      all FEE64 temperatures appear to be stable 

11.05 check ASIC control *all* FEE64s and ASICs

11.13 analysis of file May19/R2_1 - see attachment 16
      ADC rate c. 72Hz dominated by same, single hot channel (Stat spectrum ch# 104) in each of FEE64s nnaida1,
2, 5 & 6 otherwise looks OK
      sync pulser rate 10Hz confirmed by JA

17.25 all system wide checks OK *except* nnaida7 fails ADC calibration

      FEE64 temperatures OK - see attachment 18
      good event statistics OK - see attachments 19

      detector biases & leakage currents OK - see attachment 20

      Temperature + deg 24.5C dew point +8.2 deg C RH 34.1%

      Merger and TapeServer ok

10.20 System wide checks ok (except naida07 ADC calibration failure)

      FEE temperatures ok (attachment 1)

      good event statistics ok (attachment 2)

      detector bias and leakage currents ok (attachment 3)

      DAQ stopped

10.40 pulser switched off

      slow comparator threshold raised to 0x64
      
      DAQ, merger, TapeServer started - all ok (attachments 4 and 5)

      writing to file R1 in TapeData/May19 at 70 kb/s

      good event statistics (attachment 6)

16:11 Tapeserver and merger still ok
      DAQ still running
      System wide checks all ok *except nnaida7 fails ADC calibration*
      Bias and leakage currents ok - attachment 7
      FEE Temperatures ok - attachment 8
      Statistics still ok
      
      Spectrum are showing alpha events (Layout 4) - attachment 9

18:25 Tektronix clock accidentally unplugged. DAQ has stalled as a result.
      Clock reset to 50MHz 5V TTL signal

18:29 System wide check of clock status shows error message in attachment 10

      DAQ Reset
      With slow comp at oxa statistics are still good - attachment 11
      System wide checks all ok *except nnaida7 fails ADC calibration*
      Resync to the ASIC clock
      All histograms zeroed

18:37 Slow comp threshold raised to 0x64 for alpha run
      Writing to file:
      May19/R2_0
      

      

      

      

      

OH setup AIDA external clock using  Tektronix AFG3102 - settings as follows

CH1 ON - amplitude +5V, phase 0n deg, offset 0V, frequency 50.000000MHz

JA setup DTAS/BigRIPS clock using Tektronix AFG3102 - settings as follows

CH2 ON - amplitude -0.8V, phase 0n deg, offset 0V, frequency 25.000000MHz

Unfortunately the AGF3102 was set to CH1 frequency = CH2 frequency and this changed the AIDA external
clock frequency from 50MHz to 25MHz.

This stopped the DAQ. Interestingly it was possible to Resync successfully and *all* system wide
checks were OK *except* Check Clock Status which produced errors - see attachment 1.

CH1 & CH2 now set to 50MHz and 25MHz respectively.

AIDA DAQ now running OK.

AIDA@RIKEN

Selecting SETUP (Run Control tab) or Perform Timestamp Resync (AIDA Control tab) produces error message - see
attachment 1

Selecting Perform Resync (AIDA Master Timestamp Control) works OK

19.12 all system wide checks OK *except* nnaida7 fails ADC calibration

      FEE64 temperatures OK - see attachment 9
      detector biases & leakage currents OK - see attachments 10 & 11
      good event statistics OK - see attachment 12
      all FEE64s <100k, 10x < 20k

      1.8.W spectra 20us FSR - see attachments 13 & 14

09.55 all system wide checks OK *except* nnaida7 fails ADC calibration

      FEE64 temperatures OK - see attachment 1

      good event statistics OK - see attachment 2
      all FEE64s <100k, 11x < 20k

      1.8.L spectra - see attachments 3 & 4
      nnaida1 70ch FWHM, nnaida3 80 ch FWHM

      detector biases & leakage currents OK - see attachments 5 & 6

      1.8.W spectra 20us FSR - see attachments 7 & 8

      nnaida1 Options, Local Controls, Data Redaout, Discriminator Controls - see attachment 9-13

      Lost Activity Monitor -see attachment 14

18.01 DAQ found stopped

      This was caused by a chnage to the AIDA external clock frequency - see https://elog.ph.ed.ac.uk/AIDA/798

      Following change of AIDA external clock frequency to 50MHz

      DAQ RESET
      DAQ SETUP

      Sync all ASIC clocks using Resync
      
      all system wide checks OK *except* nnaida7 fails ADC calibration

      zero all histograms

      DAQ GO

18.31 FEE64 temperatures OK - see attachment 15

      good event statistics OK - see attachment 16
      all FEE64s <100k, 10x < 20k

      detector biases & leakage currents OK - see attachments 17 & 18

10:52 system wide checks ok, except naida07 fails ADC calibration
      good event statistics, rates in naida19,20,23,24 high (attachment 1)
      FEE temperatures ok (attachment 2)
      detector bias/leakage currents stable (attachment 3)

11.00 - chiller refilled and switched on
        set to 20 degrees celsius

        AIDA stand moved and secured in F11
        clock connected -> 50 MHz square wave at 5.0 V

        AIDA connected to power box
        network cables attached
        NIM modules switched on

        Raspberry Pis switched on
        Detector bias switched on for detectors 1-6
     
        
        
13.58 - AIDA power relay 1,2,5,6 sequenced on
       bias/leakage currents ok (attachment 1)
       DAQ setup
       System wide checks ok, except naida07 fails ADC calibration, and clock status check returns error in
nnaida06, 5.

       Above issue with clock no longer present

       FEE temperatures ok (attachment 2)
       good event statistics (attachment 3)

16.30 1.8.W spectra n+n strips
      FSR 20us, 200us, 2ms, 20ms attachments 4-7

      1.8.W spectra p+n strips
      FSR 20us, 200us, 2ms, 20ms attachments 8-11
       
      compare with https://elog.ph.ed.ac.uk/AIDA/746

      naida19, naida20, naida23 show low frequency noise structure, worse than in above elog entry

17.22 1.8.L spectra p+n strips

      peaks:

      aida01 72
      aida02 112
      aida03 80
      aida04 78
      aida05 74
      aida06 95
      aida07 78
      aida08 71
      aida09 82
      aida10 85
      aida11 93
      aida12 96
      aida13 101
      aida14 70
      aida15 87
      aida16 87
      aida17 69
      aida18 83
      aida19 127
      aida20 116
      aida21 84
      aida22 74
      aida23 108
      aida24 117
      

      

Inventory is currently packaged up under the AIDA desk in B3F


2 FEE64 Modules

Module 1 - MAC Addresses
2B:33:15
2B:22:6E <- Loose HDMI

Module 2 - MAC Addresses
2B:09:DA <- ASIC #1 HEC Hot Channel, LEC noisy
2B:11:C5 <- Missing ASIC

MACB A-MP 202394 -2    72-38

MACB RevB Ser38 AMP 202394-2

MACB RevB AMP 202394-2   81-49

https://docs.google.com/spreadsheets/d/12hgbrywB10hGsKt5uc2HnLfZymh8_uvM6cEASbbqnBE/edit#gid=1347508769

15.04 Plots of X Energy vs Y Energy for each detector, and for 4 different Al degrader thicknesses, as indicated
on each graph. (Attachments 1-4)

13.53 Correlation analysis plot of all detectors with 3.3mm Al degrader thickness (attachment 1)
 
13.54 Correlation analysis plot of detectors 1 and 2 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 2)
      Correlation analysis plot of detectors 3 and 4 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 3)
      Correlation analysis plot of detectors 5 and 6 with 3mm, 2.3mm and 2.8mm degrader thickness (attachment 4)

14.02 Plots made over first 200ms of data

07.56 DAQ continues - AIDA file RIBF148/R5_822
      165Pm BigRIPS setting + 2.8mm Al degrader

08.13 zeroed xy hit pattern on online analysis and MIDASsort

08.30 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 1)
      good event statistics ok (attachment 2)
      detector bias/leakage currents ok (attachment 3)

08.34 Merger and TapeServer ok, no error messages in terminal (attachments 4/5)

08.40 zeroed all spectra on online analysis and MIDASsort

08.44 BRIKEN and BigRIPS stop
      AIDA file RIBF148/R5_830

08.45 BigRIPS starts run 1087
      BRIKEN starts run 102
      AIDA on file RIBF148/R5_830

09.13 n vs p multiplicity (attachment 6)
      xy hit pattern (*deleted, took wrong screenshot, sorry! -CA@12.16*)
      Energy X vs Energy Y plot (*deleted, took wrong screenshot, sorry! -CA@12.16*)

12.17 see elog entry for 15th November 2018 00.00-08.00 (attachments 9 and 10) for screenshots of the above before
      degrader change
      
09.17 BRIKEN and BigRIPS stop
      AIDA on file RIBF148/R5_836
      beam stop to change Al degrader thickness to 3.3mm

09.23 chiller refilled while access available
      humidity, temperature, dew point measurements obtained

09.25 detector bias/ leakage currents ok (attachment 7)

09.30 zeroed all spectra in online analysis and MIDASsort

09.31 beam back on
      BRIKEN and BigRIPS start
      AIDA file RIBF148/R5_838
      BRIKEN run 103
      BigRIPS run 1088

10.32 BRIKEN and BigRIPS stop
      AIDA file RIBF148/R5_848

10.33 BRIKEN and BigRIPS start
      AIDA file RIBF148/R5_848
      BRIKEN run 104
      BigRIPS run 1089

10.45 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 8)
      good event statistics ok (attachment 10)
      detector bias/leakage currents ok (attachment 9)

11.20 ran analyser on file R5_847 - attachment 11
      no timewarps observed
      dead time in nnaida19 at ~1s out of 355.283s (~0.3%)
      rest at zero, except nnaida20 at ~0.6s and nnaida21 at ~0.1s

11.33 BRIKEN and BigRIPS stop
      AIDA file RIBF148/R5_859

11.34 BRIKEN and BigRIPS start
      AIDA file RIBF148/R5_859
      BRIKEN run 105
      BigRIPS run 1090

12.05 n vs p multiplicity (attachment 12)
      xy hit pattern (attachment 13)
      Energy X vs Energy Y plot (attachment 14)
      this is after change of Al degrader thickness to 3.3mm

12.36 BRIKEN and BigRIPS stop
      AIDA file RIBF148/R5_869

12.36 BRIKEN and BigRIPS start
      AIDA file RIBF148/R5_869
      BRIKEN run 106
      BigRIPS run 1091

12.40 online histograms
      per FEE64 Rate - attachment 15
      per FEE64 HitRate - attachment 16
      1.8.L spectra - attachments 17-20
       nnaida1 pulser peak width 70ch FWHM
      1.8.H spectra - attachments 21-22
      1.8.W spectra - attachments 23-24

12.47 beam off
      AIDA file RIBF148/R5_870

12.54 BRIKEN and BigRIPS stop
      AIDA file RIBF148/R5_871

13.10 MIDASsort analysis RIBF148/R5_871 - all ADC data synchronised - attachments 25-26

13.16 correlation analysis decay plots for each detector with the Al degrader thickness at 3.3mm (attachment 23)
      see elog entry November 15th 2018 00:00-08:00 (attachments 16-18) for same plots with previous degrader
      thickness.

13.26 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 24)
      good event statistics ok (attachment 25)
      detector bias/leakage currents ok (attachment 26)

15.04 see other elog entries for correlation analysis and high energy Ex vs Ey plots compared between different Al
degrader thicknesses.

15.38 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 28)
      good event statistics ok (attachment 27)
      detector bias/leakage currents ok (attachment 29)

15.55 BRIKEN start background measurement
      BRIKEN not writing to file
      AIDA file RIBF148/R5_896
      Online histograms available

16.00 BRIKEN start writing to file
      AIDA file RIBF/R5_897
      BRIKEN run 107

17.18 DAQ stop AIDA file RIBF148/R5_907

      End of run RIBF148 due to accelerator problems requiring ~3-4 days to fix
      'low' mass BigRIPS setting postponed 

      ASIC check load

      all onine histograms zero'd

17.22 DAQ start AIDA file RIBF148/R6
      Pulser walkthrough
      BNC PB-4 amplitudes 90,000 - 10,000 @ 10,000 step
      x5 attenuator IN
      Frequency 25Hz range
      Delay MIN
      Polarity -
      Tail pulse

17.37 DAQ trop AIDA file RIBF148/R6_2
      1.8.L spectra - see attachments 30 & 31
 

17.40 DAQ start AIDA file RIBF148/R7
      Pulser walkthrough
      BNC PB-4 amplitudes 1,200 - 1,000 @ 1,000 step
      x5 attenuator IN
      Frequency 25Hz range
      Delay MIN
      Polarity -
      Tail pulse

17.50 DAQ stop AIDA file RIBF148/R7_1
      1.8.L spectra - see attachments 32 & 33

17.54 DAQ start AIDA file RIBF148/R8
      background
      BNC PB-4 pulser OFF

18.00 detector biases & leakage currents OK - see attachments 34 & 35

      FEE64 temperatures OK - see attachment 36
      good event statistics OK - see attachments 37

      Merger OK - see attachment 38
      TapeServer OK - see attachment 39
      no error or warning messages terminal server sesssions reported

      per FEE64 Rate spectra - attachment 40

      1.8.W spectra 20ms FSR - attachments 41 & 42

18.10 DAQ stop AIDA file RIBF148/R8_2

      Detector bias OFF
      FEE64 power OFF

18.12 Ambient temperature +25.5 deg C, d.p. +2.2 deg C, RH 21.5%

18.15 Withdraw AIDA from BRIKEN - done

      2x NIM bin OFF
      1x NIM bin fan tray OFF
      1x USB ac mains relay OFF
      Julabo FL11006 chiller OFF front panel/rear panel/wall-mounted 3ph outlet
      2x network cables disconnected and coiled/cable-tied to stairwell railings
      disconnect coorelation scaler trigger & reset inputs to root MACB front panel
      disconnect 50MHz TTL clock root MACB rear panel
      disconnect AIDA plastic veto
      discopnnect 2x ac mains cabnles from ac mains distribution box

      remove AIDA support assembly nose support
19.00 raise AIDA support assembly feet/lower AIDA support assembly wheels from/to F11 floor


       











 








      
      












      



      



      


  
     
      






 

00.25 System wide checks ok * except nnaida 7 fails adc*
      FEE Temps ok - attachment 1
      Stats ok - attachment 2 
      Leakage currents ok - attachment 3
      tape server and merger ok

00:57 BigRIPS and BRIKEN stop
      AIDA on file R5_753

00.59 BigRIPS starts run 1079
      BRIKEN starts run 94
      AIDA on file R5_753

01:56 BigRIPS and BRIKEN stop
      AIDA on file R5_762

01.57 BigRIPS starts run 1080
      BRIKEN starts run 95
      AIDA on file R5_762

02:47 BigRIPS and BRIKEN stop
      AIDA on file R5_770

02.48 BigRIPS starts run 1081
      BRIKEN starts run 96
      AIDA on file R5_770

03:45 BigRIPS and BRIKEN stop
      AIDA on file R5_780

03.47 BigRIPS starts run 1082
      BRIKEN starts run 97
      AIDA on file R5_780

04:45 BigRIPS and BRIKEN stop
      AIDA on file R5_790

04.47 BigRIPS starts run 1083
      BRIKEN starts run 98
      AIDA on file R5_790

04.50 System wide checks ok * except nnaida 7 fails adc*
      FEE Temps ok - attachment 4
      Stats ok - attachment 5
      Leakage currents ok - attachment 6
      tape server and merger ok

05.46 BigRIPS and BRIKEN stop
      AIDA on file R5_800

05.47 BigRIPS starts run 1084
      BRIKEN starts run 99
      AIDA on file R5_800

06.45 BigRIPS and BRIKEN stop
      AIDA on file R5_810

06.46 BigRIPS starts run 1085
      BRIKEN starts run 100
      AIDA on file R5_810

07.25 System wide checks ok * except nnaida 7 fails adc*
      FEE Temps ok - attachment 7
      Stats ok - attachment 8
      Leakage currents ok - attachment 9
      tape server and merger ok

07.44 BigRIPS and BRIKEN stop
      AIDA on file R5_820

07.45 BigRIPS starts run 1086
      BRIKEN starts run 101
      AIDA on file R5_820

15:51 DAQ continues - AIDA file RIBF148/R5_664
      165Pm BigRIPS setting + 2.8mm Al degrader

      ASIC settings 2018Oct03-13.26.58
       from c. 09.00 13.11.18
       n+n FEE64s Ibias LF feedback 0xb -> 0xd
       HEC fast comparator threshold 0x20 -> 0xff

15:52 Beam out due to power fault somewhere.

15:53 Beam back
      BRIKEN and BigRIPS start
      BRIKEN file 181115_1553_165Pm_085.dlt  
      BigRIPS run 1070
      AIDA on run R5_664

16:00 System wide checks all ok *Except nnaida7 fails adc calibration*
      Leakage currents and bias ok - attachment 1
      FEE Temps ok - attachment 2
      Statistics ok - attachment 3

16:54 BRIKEN and BigRIPS stop
      AIDA on file R5_675

16:55 BRIKEN starts run 181115_1654_165Pm_086.dlt
      BigRIPS starts run 1071
      AIDA on file R5_675

17:30 BRIKEBN and BigRIPS stop for BigRIPS team to get access

13:46 BRIKEN sends sync pulse resetting timestamp
      AIDA on file R5_683

17:49 BRIKEN starts run 181115_1748_165Pm_087.dlt
      bigRIPS starts run 1072
      AIDA on file R5_683

18.00 System wide checks ok, except nnaida7 ADC calibration failure
      FEE64 Temperatures ok (attachment 4)
      Good event statistics ok (attachment 5)
      Detector bias/Leakage currents ok (attachment 6)

18.04 Merger and TapeServer run ok - no error messages in terminals (attachments 7 and 8)

18:48 BigRIPS and BRIKEN stop
      AIDA on file R5_693

18:49 BigRIPS starts run 1073
      BRIKEN starts run 181115_1849_165Pm_088.dlt
      AIDA on file R5_693

19:47 BgiRIPS and BRIKEN stop
      AIDA on file R5_703

19:48 BigRIPS starts run 1074
      BRIKEN starts run 181115_1947_165Pm_089.dlt  
      AIDA on file R5_703

20:54 bigRIPS and BRIKEN stop
      AIDA on file R5_714

20:55 bigRIPS starts run 1075
      BRIKEN starts run 181115_2053_165Pm_090.dlt
      AIDA on file R5_714

21:25 System wide checks all ok *Except nnaida 7 fails adc calibration*
      Bias and leakage currents ok - attachment 9
      FEE Temps all ok - attachment 10
      Statistics ok - attachment 11

21:55 BRIKEN and BigRIPS stop
      AIDA on file R5_724

21:56 BigRIPS starts on run 1076
      BRIKEN starts run
      AIDA on file R5_724

22:55 BigRIPS and BRIKEN stop
      AIDA on file R5_733

22:56 BRIKEN Starts run
      BigRIPS starts run 1077
      AIDA on file R5_733

23.53 Briken stops
      AIDA on file R5_743

23.55 BRIKEN starts
      bigRIPS run 1078
      BRIKEN starts run 93
      AIDA on file R5_743

08.10 BRIKEN stop
      AIDA file RIBF148/R5_587

08.11 BRIKEN start
      AIDA file RIBF148/R5_588
      BRIKEN run 77
      BigRIPS run 1062

08.16 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 1)
      good event statistics ok (attachment 2)
      detector bias/leakage currents ok (attachment 3)
      Merger and TapeServer still ok

09.11 BRIKEN stop
      AIDA file RIBF148/R5_598

09.13 BRIKEN start
      AIDA file RIBF148/R5_598
      BRIKEN run 78
      BigRIPS run 1063

10.10 BRIKEN stop
      AIDA file RIBF148/R5_608

10.12 BRIKEN start
      AIDA file RIBF148/R5_608
      BRIKEN run 79
      BigRIPS run 1064

11.10 BRIKEN stop
      AIDA file RIBF148/R5_618

11.12 BRIKEN start
      AIDA file RIBF148/R5_618
      BRIKEN run 80
      BigRIPS run 1065

11.17 system wide checks ok, except nnaida7 ADC calibration failure
      FEE64 temperatures ok (attachment 4)
      good event statistics ok (attachment 5)
      detector bias/leakage currents ok (attachment 6)
      Merger and TapeServer still ok

12:10 BigRIPS and BRIKEN stop
      AIDA on file R5_628

12:11 BRIKEN start
      AIDA on file R5_628
      BigRIPS run 1066
      BRIKEN run 81 181115_1211_165Pm_081.dlt

13.10 BRIKEN stop
      AIDA file RIBF148/R5_638

13.12 BRIKEN start
      AIDA file RIBF148/R5_638
      BRIKEN run 82
      BigRIPS run 1067

13.32 AIDA file RIBF148/R5_642
      BRIKEN stopped
      Turning beam off to access area

13.50 AIDA file RIBF148/R5_644
      beam back on
      BRIKEN run 83
      BigRIPS run 1068

14.26 MIDASsort analysis file RIBF148/R5_648 - all ADC data synchronised - attachment 7
      analysis of file RIBF148/R5_648 - attachment 8
       nnaida19 dead time ~0.5% - all other deadtimes lower or 0% - no timewarps

14.35 1.8.W spectra layout ID 8 (attachment 9)

14.50 BRIKEN stop
      AIDA file RIBF148/R5_654

14.51 BRIKEN start
      AIDA file RIBF148/R5_654
      BRIKEN run 83
      BigRIPS run 1068

15.10 1.8.H high energy channel spectra (attachment 10)

15.35 beam off
      AIDA file RIBF148/R5_662
      BRIKEN and BigRIPS stopped run