 Thu Nov 2 01:56:18 2017, TD, OH, Thursday 2 November 16x
|
10.56 DAQ running OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
p+n FEE64s 1.8.L spectra - see attachment 5 - nnaida17 FWHM 63 ch
n+n FEE64s 1.8.L spectra - see attachment 6 - nnaida3 FWHM 78 ch
per FEE64 rate spectra - see attachments 7 & 8
11.06 all spectra zero'd
17.28 Detector biases & leakage currents OK - see attachments 9 & 10
FEE64 Temperatures OK - see attachment 11
DAQ statistics OK - see attachment 12
*all* system wide checks OK *except* nnaida21 fails ADC calibration
18.46 per PJCS request two screenshots of nnaida21:8015/AIDA/MONLOCK/MONLOCK.tml
see attachments 13 & 14
23:52 Statistics still good - Attachment 15
Leakage and bias ok - Attachment 16 |
|
Wed Nov 1 02:24:20 2017, OH, Wednesday 1 November
|
11:24 DAQ running OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1
FEE64 Temperatures OK - see attachment 2
DAQ statistics OK - see attachment 3
*all* system wide checks OK *except* nnaida21 fails ADC calibration |
|
Tue Oct 31 05:57:33 2017, TD, Offline analysis RIBF128/R5_124-R5_148 and Oct17/R31_17-R17_34 10x
|
Offline analysis of the AIDA Oct17/R17_31 to R17_34 data "84Ge setting"
compared to an equivalent analysis of the AIDA RIBF128/R5_124 to R5_148
data from the 130Ag setting of the June 2017 RIBF128 experiment.
N.B.
1) no software thresholds
2) no PID correlation
3) unless otherwise stated, all implant energies are the stopping layer implant energies
Attachment 1 - implantation energy (20MeV/ch, range 20.48GeV)
versus
per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
The 130Ag data (lower) clearly shows the "20ms bump", there is no
evidence for a "20ms bump" in the "84Ge" data (upper).
Note the non-observation of the "20ms bump" in the "84Ge" data
is not explained by the larger range of implant energies of the
130Ag data ( see attachment 7 )
Attachments 2-3 - per pixel implant-decay times (163.84us/ch)
upper 130Ag setting
lower "84Ge setting"
Attachments 4-5 - per pixel implant-decay times (163.84us/ch)
red 130Ag setting
yellow "84Ge setting"
Attachment 6 - *total* implant energy for AIDA DSSSD stack (5.6MeV/channel)
yellow 130Ag setting
red "84Ge setting"
Attachment 7 - implant energy for stopping DSSSD layer (20MeV/channel)
red 130Ag setting
yellow "84Ge setting"
Attachment 8 - per pixel decay-decay correlation time (163.84us/ch, range 16.78ms)
versus
per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
upper "84Ge setting"
lower 130Ag setting
Attachment 9 - x and y-axis projections for 130Ag setting spectrum
@x per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
@y per pixel decay-decay correlation time (163.84us/ch, range 16.78ms)
Attachment 10 - x and y-axis projections for "84Ge setting" setting spectrum
@x per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
@y per pixel decay-decay correlation time (163.84us/ch, range 16.78ms) |
|
Tue Oct 31 00:34:10 2017, TD, OH, Tuesday 31 October 8x
|
09.34 DAQ running OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
15.02 Detector biases & leakage currents OK - see attachments 5 & 6
FEE64 Temperatures OK - see attachment 7
DAQ statistics OK - see attachment 8
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Ambient temperature +24.3 deg C, d.p. -0.2 deg C, RH 19.8%
Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C, water level OK c. mid-point
middle-upper marker
|
|
Mon Oct 30 01:10:28 2017, TD, OH, Monday 30 October 8x
|
10.10 DAQ running OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
15.56 Detector biases & leakage currents OK - see attachments 5 & 6
FEE64 Temperatures OK - see attachment 7
DAQ statistics OK - see attachment 8
*all* system wide checks OK *except* nnaida21 fails ADC calibration |
|
Sun Oct 29 05:16:35 2017, TD, OH, Sunday 29 October 14x
|
14.16 DAQ running OK - data transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C
Ambient temperature +23.9 deg C, d.p. +10.8 deg C, RH 43.2%
15.05 per FEE64 Rate, 1.8.L and 1.8.W spectra - note common x & y scales
Peak width nnaida5 63 ch FWHM
Peak width nnaida8 82 ch FWHM
15.09 All histograms zero'd
18.25 Detector biases & leakage currents OK - see attachments 11 & 12
FEE64 Temperatures OK - see attachment 13
DAQ statistics OK - see attachment 14
*all* system wide checks OK *except* nnaida21 fails ADC calibration |
|
Sat Oct 28 06:25:07 2017, TD, Waveforms 10x
|
For comparison with waveforms shown in https://elog.ph.ed.ac.uk/AIDA/665 and https://elog.ph.ed.ac.uk/AIDA/668
Note; nnaida21 ADC did not calibrate during setup therefore no waveforms for this FEE64
Current configuration
p+n junction strips FEE64 adaptor PCB rev D -> FEE64 adaptor PCB rev E
ac coupling 10n/100V/X7R -> 33n/100V/X7R
detector bias RC filter 3.3k/10n added
ASIC setting Ibias LF feedback 0x8 -> 0xf *except* nnaida2 ->0xc
n+n ohmic strips FEE64 adaptor PCB rev C *no change*
ASIC setting Ibias LF feedback 0xb *no change*
Attachments 1-5 waveforms for n+n ohmic strips
Attachment 1 - per FEE64 1.8.W, 20us range
Attachment 2 - per FEE64 1.8.W, 20us range, expanded y=scale
Attachment 3 - per FEE64 1.8.W, 200us range, expanded y=scale
Attachment 4 - per FEE64 1.8.W, 2ms range, expanded y=scale
Attachment 5 - per FEE64 1.8.W, 20ms range, expanded y=scale
Attachments 6-10 waveforms for p+n junction strips
Attachment 6 - per FEE64 1.8.W, 20us range
Attachment 7 - per FEE64 1.8.W, 20us range, expanded y=scale
Attachment 8 - per FEE64 1.8.W, 200us range, expanded y=scale
Attachment 9 - per FEE64 1.8.W, 2ms range, expanded y=scale
Attachment 10 - per FEE64 1.8.W, 20ms range, expanded y=scale |
|
Sat Oct 28 06:09:44 2017, TD, Offline analysis Oct17/R17_31-R17_34 20x
|
|
|
Sat Oct 28 03:33:10 2017, TD, OH, Saturday 28 October 13x
|
11.33 DAQ running OK - date transfer not enabled
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
DAQ statistics OK - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C
Ambient temperature +26.2 deg C, d.p. +6.2 deg C, RH 28.3%
14.40 Detector biases & leakage currents OK - see attachments 5 & 6
FEE64 Temperatures OK - see attachment 7
DAQ statistics OK - see attachment 8
*all* system wide checks OK *except* nnaida21 fails ADC calibration
14.50 DAQ starts
AIDA data file Oct17/R18
14.53 per FEE64 rates (20us/channel) - see attachment 9
No indication of c. 400us period noise as indicated by DAQ statistics attachment 8
15.46 DAQ stopped
DAQ start - data tranfser disabled
19.40 Detector biases & leakage currents OK - see attachments 10 & 11
FEE64 Temperatures OK - see attachment 12
DAQ statistics OK - see attachment 13
*all* system wide checks OK *except* nnaida21 fails ADC calibration |
|
Fri Oct 27 08:35:33 2017, TD, Offline analysis Oct17/R17_31-R17_34 8x
|
Offline analysis of High Energy Channel (HEC) 20GeV FSR data from AIDA data file Oct17/R17_31-R17_34
Degrader OUT
Attachment 1 - per DSSSD #1-6 m_p versus m_n
Attachment 2 - 2D spectra contour levels/colours
Attachment 3 - per DSSSD #1-6 x versus y
Attachment 4 - per DSSSD #1-6 E_p versus E_n (20MeV/channel nominal)
Attachments 5-7 - as above but with all statistics from AIDA data files Oct17/R17_34
Attachment 8 - Sum of E_p energies for DSSSD #1-6 (5.6MeV/channel nominal)
Peak at channel 1450 corresponds to an energy of 8.1GeV
End of spectrum channel 1850 corresponds to 10.4GeV
Note - HEC data not gain-matched
Using nominal HEC calibration accurate to ~ +/-20%
|
|
Fri Oct 27 01:58:44 2017, TD, OH, Friday 27 October 12x
|
09.56 DAQ stopped OK yesterday
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Julabo FL11006 recirculating chiller coolant reservoir refilled - set point +20 deg C, actual +20.0 deg C
Ambient temperature +23.6 deg C, d.p. +6.2 deg C, RH 32.2%
AIDA withdrawn from (CH2)n matrix
DAQ started - no data transfer
good events statistics stable - see attachment 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
13:30 System wide checks ok
Stats - Attachment 6
FEE temperatures ok - Attachment 7
leakage and bias ok - Attachment 8
17.15 Detector biases & leakage currents OK - see attachments 9 & 10
FEE64 Temperatures OK - see attachment 11
good events statistics stable - see attachment 12
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Ambient temperature +25.2 deg C, d.p. +5.7 deg C, RH 28.5% |
|
Wed Oct 25 18:36:46 2017, TD, OH, Thursday 26 October 28x
|
02.37 DAQ stalled - USB-controlled ac mains relay fuse blown
Not writing to disk
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa
Detector biases & leakage currents OK - see attachments 1 & 2
*all* system wide checks OK *except* nnaida21 fails ADC calibration
Ambient temperature +24.3 deg C, d.p. +8.7 deg C, RH 37.1%
02.54 Replace 250V/16A fuse and power up
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachments 4
03:30 Stats with nnaida13 slow comparator threshold raised to 140keV - Attachment 5
03:50 Pulser widths done, slow comparator threshold raised to 0xc ~120keV for nnaida 19-22
Statistics - Attachment 6
05:40 Beam now going into F11. Wasabi and YSol in front of AIDA
AIDA is seeing light particles
Waveforms look good
Layout 7 - Attachment 7
layout 8 - Attachment 8
Statistics with light particles going through - Attachment 9
Bias and leakage currents ok - Attachment 10
We are taking the light ion data to file in R17_*
06:50 Light ion data continues
System wide checks all ok
07:22 Bias and leakage ok - Attachment 11
FEE Temperatures ok - Attachment 12
Stats - Attachment 13
08:15 Light ions stop still writing file
08:27 Beam into aida run R17_30
Zero degrader, just 4mm of WAS3ABI
WAS3ABI run 120
BRIKEN started run at 08:27 run 18
BIGRIPS Run 8
Timestamp reset at 08:27
Stats with beam - Attachment 14
08:44 Waveforms with implants in the detector
Layout 7 - Attachments 15 & 16
Layout 8 - Attachments 17 & 18
Layout 1 linear and log attachments 19 & 20
Leakage and bias ok - Attachment 21
09:14 Just noticed the stats in nnaida13 has dropped rate. Noise source may have been turned off
Statistics - Attachment 22
Spectra from the 0mm degrader run - Attachments 22-27
09:20 BRIKEN and WAS3ABI stop on run 162 aida on R17_35
1mm degrader moved in
BigRIPS on run 9
BRIKEN run 19
WAS3ABI start on 163
AIDA on R17_35
Rates similar to last screenshot of stats 09:14
09:26 Leakage and bias ok - Attachment 28
09:41 Beam stops
AIDA on file R17_37
BRIKEN stops running
WAS3ABI on run 178
AIDA Files written
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:22 R17_29
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:31 R17_30
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:40 R17_31
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:50 R17_32
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:00 R17_33
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:10 R17_34
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:21 R17_35
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:31 R17_36
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:42 R17_37
-rw-rw-rw-. 1 npg npgstaff 329M Oct 26 09:44 R17_38 |
|
Wed Oct 25 03:26:55 2017, TD, OH, Wednesday 25 October 7x
|
11.27 DAQ continues
Not writing to disk
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
*all* FEE64s slow comparators 0xa
Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachments 4
*all* system wide checks OK *except* nnaida21 fails ADC calibration
11.47 Ambient temperature +23.9 deg C, d.p. +9.0 deg C, RH 39.0%
16:45 System wide checks all ok
FEE temps ok - Attachment 5
Stats - Attachment 6
Bias and leakage ok - Attachment 7 |
|
Tue Oct 24 03:16:07 2017, TD, OH, Tuesday 24 October 20x
|
11.16 DAQ continues
AIDA file Oct17/R8_107
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
11.20 Detector biases & leakage currents OK - see attachments 1 & 2
FEE64 Temperatures OK - see attachment 3
good events statistics stable & OK - see attachments 4 & 5
no merger/tapeserver errors reported since start of run - see attachments 6 & 7
*all* system wide checks OK *except* nnaida21 fails ADC calibration
11.30 Ambient temperature +23.3 deg C, d.p. +4.1 deg C, RH 28.7%
11.30 analysis file Oct17/R7_108 - zero deadtime, 6x MBS and zero ts timewarps - see attachment 8
11.39 DAQ stop
11.44 DAQ start
AIDA file Oct17/R9
Pulser walkthrough
BNC PB-4
Amplitude 90,000-10,000 @ 10,000 step
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 250Hz
delay MIN, tail pulse, INT ref
11.53 DAQ stop
See attachment 8
11.44 DAQ start
AIDA file Oct17/R10
Pulser walkthrough
BNC PB-4
Amplitude 12,000-2,000 @ 2,000 step
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 250Hz
delay MIN, tail pulse, INT ref
11.53 DAQ stop
See attachment 9
12.06 DAQ starts
AIDA file Oct17/R12
BNC PB-4
Amplitude 90,000
x5 attenuator IN
t_r 100ns tau_d 50us
- polarity
frequency range 25Hz
delay MIN, tail pulse, INT ref
ASIC settings 2017Oct23-14.38.03
14.41 online analysis
ADC synchronised - see attachment 10
17.12 DAQ starts
AIDA file Oct17/R13
Background for LuckyDoll automatic threshold determination
BNC PB-4 OFF
ASIC settings 2017Oct23-14.38.03
Slow comparator nnaida13 0xc, nnaida19-22 0xb, all other FEE64s 0xa
DAQ statistics - see attachment 11
17.27 DAQ stop
18.03 DAQ starts
AIDA file Oct17/R16
Background for LuckyDoll automatic threshold determination
BNC PB-4 OFF
ASIC settings 2017Oct23-14.38.03
Slow comparator *all* FEE64s 0xa
DAQ statistics - see attachment 12
18.22 DAQ stop
18.48 DAQ statistics
Slow comparator *all* FEE64s 0xa - see attachment 13
Slow comparator *all* FEE64s 0x9 - see attachment 14
Slow comparator *all* FEE64s 0x8 - see attachment 15
Slow comparator *all* FEE64s 0x7 - see attachment 16
18.53 Detector biases & leakage currents OK - see attachments 13 & 14
FEE64 Temperatures OK - see attachment 15
*all* system wide checks OK *except* nnaida21 fails ADC calibration |
|
Mon Oct 23 02:24:14 2017, TD, OH, Monday 23 October 19x
|
10:18 Leakage and bias ok - Attachment 1
FEE temperatures ok - Attachment 2
Statistics - Attachment 3
DAQ continues ok
10:23 DAQ stopped on R7_10
Alpha run through night
10:28 MIDAS Sort spectra from the alpha run
Ep versus En - Attachment 4
x versus y 2D hit pattern - Attachment 5
Front versus back multiplicity - Attachment 6
2D Hit pattern indicates detection of alphas in all 4 regions of each of the 6 detectors
indicates cabling is ok
11:55 FEEs turned off after being unable to recover after crash
13:49 FEEs powered on again
Pi monitor indicates panic on nnaida22 the FEE that crashed
ReSync done on setup except for 23 and 24
Master ReSync done succesfully
ASIC settings loaded default to 2017Mar27
Restoring 2017Oct22
System wide checks ok
Leakage and bias ok - Attachment 7
FEE temperatures crashed - Attachment 8
Upon reboot all rates across the FEEs appear lower
In particular 13 and 14. Thresholds have been reduced back to 0xa for all ASICs on both FEEs
Layout 1 linear common y of 2000 - Attachment 9
Layout 1 log common y of 10 - Attachment 10
All front side FEE64 1.8.W waveforms - 20us range - Attachment 11
All back side FEE64 1.8.W waveforms - 20us range - Attachment 12
All front side FEE64 1.8.W waveforms - 2ms range - Attachment 13
All back side FEE64 1.8.W waveforms - 2m range - Attachment 14
FEE64 nnaida13 1.*.W waveforms - Ibias LF 0xf - 2ms range - Attachment 15
Statistics after switch and thresholds lowered - Attachment 16
Pulser widths measured. On boards changed 10 out of 12 FEEs show greater than 10% improvements
11 out of 24 total show greater than 10%
FEE stats post pulser width - Attachment 17
New ASIC settings DB key: 2017Oct23-14.38.03
Slow comparator 0xa for all FEE64s and all ASICs
IBias LF feedback at 0xf for all front side FEEs except nnaida 2 which is at 0xc
IBias LF feedback at 0xb for all back side FEEs
ASIC settings DB file checked OK
Ambient temperature +23.3 deg C, D.P +7.1 deg C, R.H. 35.2%
Julabo FL11006 set point +20.0 deg C, water le
15:38 Merger and TapeServer screenshots - Attachments 17-18
|
 Mon Oct 23 11:50:09 2017, TD, OH, Mon 23 Oct - further information please.
|
> 10:18 Leakage and bias ok - Attachment 1
> FEE temperatures ok - Attachment 2
> Statistics - Attachment 3
> DAQ continues ok
>
> 10:23 DAQ stopped on R7_10
> Alpha run through night
>
> 10:28 MIDAS Sort spectra from the alpha run
> Ep versus En - Attachment 4
> x versus y 2D hit pattern - Attachment 5
> Front versus back multiplicity - Attachment 6
>
> 2D Hit pattern indicates detection of alphas in all 4 regions of each of the 6 detectors
> indicates cabling is ok
>
> 11:55 FEEs turned off after being unable to recover after crash
Please could you define this 'crash' to allow a better understanding of problems with the system.
For example.... what is unresponsive.... does a parse of the FEE64 log files ( before doing anything ) reveal a panic that is new? Does a STOP of the Tape work ? Does a Toggle of the MERGE pause state
work ?
Thus it will be possible to say that ..... FEE # is always the one responsible for DAQ failure or by < ???? > or the MERGE has found < ??? > problem.
Thanks in advance ;-)))
>
> 13:49 FEEs powered on again
> Pi monitor indicates panic on nnaida22 the FEE that crashed
>
> ReSync done on setup except for 23 and 24
> Master ReSync done succesfully
> ASIC settings loaded default to 2017Mar27
> Restoring 2017Oct22
>
> System wide checks ok
> Leakage and bias ok - Attachment 7
> FEE temperatures crashed - Attachment 8
>
> Upon reboot all rates across the FEEs appear lower
> In particular 13 and 14. Thresholds have been reduced back to 0xa for all ASICs on both FEEs
>
> Layout 1 linear common y of 2000 - Attachment 9
> Layout 1 log common y of 10 - Attachment 10
>
> All front side FEE64 1.8.W waveforms - 20us range - Attachment 11
> All back side FEE64 1.8.W waveforms - 20us range - Attachment 12
>
> All front side FEE64 1.8.W waveforms - 2ms range - Attachment 13
> All back side FEE64 1.8.W waveforms - 2m range - Attachment 14
>
> FEE64 nnaida13 1.*.W waveforms - Ibias LF 0xf - 2ms range - Attachment 15
>
> Statistics after switch and thresholds lowered - Attachment 16
> Pulser widths measured. On boards changed 10 out of 12 FEEs show greater than 10% improvements
> 11 out of 24 total show greater than 10%
> FEE stats post pulser width - Attachment 17
>
> New ASIC settings DB key: 2017Oct23-14.38.03
> Slow comparator 0xa for all FEE64s and all ASICs
> IBias LF feedback at 0xf for all front side FEEs except nnaida 2 which is at 0xc
> IBias LF feedback at 0xb for all back side FEEs
> ASIC settings DB file checked OK
>
> Ambient temperature +23.3 deg C, D.P +7.1 deg C, R.H. 35.2%
> Julabo FL11006 set point +20.0 deg C, water le
>
> 15:38 Merger and TapeServer screenshots - Attachments 17-18
> |
|
Sun Oct 22 02:10:03 2017, OH, Sunday 22 October 25x
|
10:10 DAQ found crashed
Stopped writing to file at 05:31
System wide checks ok
Statistics - Attachment 1
FEE temperatures - Attachment 2
Error message when stopping the DAQ - Attachment 3
Bias and leakage currents ok - Attachment 4
10:18 Error when trying to reset and setup DAQ - Attachment 5
Followed by:
STATE for nnaida1 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida1:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida1:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida2 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida2:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida2:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida3 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida3:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida3:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida4 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida4:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida4:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida5 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida5:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida5:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida6 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida6:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida6:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida7 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida7:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida7:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState"
("eval" body line 1)
invoked from within
"eval ::SOAP::invoke ::SOAP::_DataAcquisitionControlClient__GetState $args"
(procedure "DataAcquisitionControlClient__GetState" line 1)
invoked from within
"DataAcquisitionControlClient__GetState"
STATE for nnaida8 returned with an error
connect failed
NONE
connect failed
while executing
"::http::geturl http://nnaida8:8015/DataAcquisitionControlServer -headers {} -type text/xml -timeout 20000
-query {<?xml version="1.0" encoding="UTF-8"..."
("eval" body line 1)
invoked from within
"eval [list ::http::geturl $url] $args"
(procedure "::http::geturl_followRedirects" line 4)
invoked from within
"::http::geturl_followRedirects http://nnaida8:8015/DataAcquisitionControlServer -headers {} -type text/xml
-timeout 20000 -query {<?xml version="1.0" ..."
("eval" body line 1)
invoked from within
"eval ::http::geturl_followRedirects [list $url] -headers [list $local_headers] -type text/xml -timeout
$timeout -query [list $request] $local_pro..."
(procedure "::SOAP::Transport::http::xfer" line 61)
invoked from within
"$transport $procVarName $url $req"
(procedure "::SOAP::invoke" line 18)
invoked from within
"::SOAP::invoke ::SOAP::_DataAcquisitionControl
10:26 Unable to recover from crash by restarting the merger
FEEs turned off. Will leave off whilst changing the adapter boards
11.28 Power up all FEE64s - 20s between each relay
11.46 Pi Monitor Browser reports all FEE64s 'Finished OK', all FEE64s '0 panics'
15:12 Waveforms of FEEs 5,6,9,10,17,18,13,14 showing the change in Ibias LF feedback value
First attachment will be waveform with LF 0x8 and second will be 0xF
FEE13 has only one as was on the rails at anything above 0x8 - Attachments 6-20
Waveforms for FEEs 19 and 20 for comparisons - Attachments 21 & 22
Attachment FEE Change
6 5 default
7 5 LF 0xf
8 6 default
9 6 LF 0xf
10 9 default
11 9 LF 0xf
12 10 default
13 10 LF 0xf
14 17 default
15 17 LF 0xf
16 18 default
17 18 LF 0xf
18 13 default
19 14 default
20 14 LF 0xf
21 19 default
22 20 default
16:02 New ASIC settings folder 2017Oct22-15.59.25
Settings changed related to A and C FEEs in which Ibias LF Feedback has been changed to LF0x8 for all
with the exception of FEE 2 which is set to 0xC and 14 which is set to 0x8
ASIC 1 of nnaida14 has a SC threshold of 0x20
All of nnaida 13 has a SC threshold of 0xf
Stats running in these setting - Attachment 23
System wide checks ok
FEE temperatures ok - Attachment 24
Leakage and bias ok - Attachment 25
16.16 Start Oct17/R7
Background alpha activity
BNC PB-4 Pulser OFF
ASIC settings per 2017Oct22-15.59.25 |
|
Sat Oct 21 02:48:17 2017, OH, TD, Saturday 21st October 31x
|
10:48 Adapter boards replaced for DSSD 1 &2 (FEEs 1,2,22 and 21)
Previous boards were Rev D new boards are Rev E
System wide checks ok
FEE Temperatures ok - Attachment 1
10:54 DSSDs biased up. Note that after new boards installed DSSD 1 and 2 had leakage currents of around 9uA
during ramp up
Leakage currents appear to have dropped as they reach 100V set point
T = 23.8 H = 45% D.P = +11.1
Leakage and Bias ok - Attachment 2
11:11 Waveforms for FEEs 22, 21, 11 and 13 - Attachments 3 - 10
Statistics - Attachment 11
14:00 System wide checks all ok
Leakage and bias ok - Attachment 12
FEE temperatures ok - Attachment 13
14:26 Spectra comparing the values for nnaida waveforms for different Ibias LF Feedback values
Values are indicated in image title. If not mentioned value 0x8 - Attachments 14 - 23
14:37 Spectra showing the effect of different slow comparator values on the sawtooth signal in the waveforms
Spectra are all nnaida22 and slow comparator values in image titles - Attachments 24 - 26
Attachment FEE Change
14 1 default
15 1 LF 0xf
16 2 default
17 2 LF 0xf
18 2 LF 0xc
19 21 default
20 21 default
21 21 LF 0xf
22 22 default
23 22 LF 0xf
24 22 LF 0xf SC 0xf
25 22 LF 0xf SC 0xd
26 22 LF 0xf SC 0xb
15:09 Raised slow comparator threshold to 0x40 ~ 640keV for all FEEs and all ASICs
Hit pattern in attachment 27
Statistics - Attachment 28
New adapter boards appear to have improved the amount of white noise at default ASIC settings
This is shown with the decrease in statistics and also in the waveforms.
At default settings the saw tooth patterns still appear in the waveforms though attenuated
with lower frequencies and lower amplitudes.
Further improvements can be gained in reducing the amplitude and frequency of the saw tooth
patterns by changing the Ibias LF feedback value though care has to be taken that the pre-amp
signal is not taken to the rails. Hence FEE 2 has a value of 0xc rather than 0xf like the others.
Hit pattern checked for the pulser by raising the slow comparator threshold to 640keV. The boards that
have been changed show a much more believable rate than those that haven't which are still showing
higher than pulser rates.
16:09 The effect of changing the shaping time on the pulser widths was checked.
Optimum still appears to be at around 8us
16:50 DAQ started writing to Oct17/R5 @ 8Mb/s
nnaida 13 SC threshold at 0x20
System wide checks ok
Leakage and bias ok - Attachment 29
FEE Temp ok - Attachment 30
Statistics - Attachment 31 |
|
Fri Oct 20 01:43:40 2017, OH, Friday 20th October 6x
|
09:43 DAQ continues ok
System wide checks all ok
Detector bias and leakage ok - Attachment 1
FEE temperatures ok - Attachment 2
On file R3_279 writing at ~11Mb/s
10:07 Waveforms for nnaida 13, 11, 20 and 22 - Attachments 3-7
nnaida 13 & 22 p-side
nnaida 11 & 20 n-side
Preamp feedback settings for ASIC are still default
10:49 DAQ Stopped
Detector bias taken off |
|
Thu Oct 19 01:40:35 2017, TD, OH, Thursday 19 October 35x
|
09.40 DAQ continues OK
File /TapeData/Oct17/R1_280
BNC PB-4 Pulser frequency switched from 250Hz to 25Hz range
09:54 ASIC Temperatures - Attachment 1
Bias and leakage currents ok - Attachments 2 & 3
Statistics - Attachment 4
10:19 Output of analysis of R1_291 - Attachment 5
11:02 Pulser widths measured before changing jumpers (In log book)
DAQ stopped on Run R1_304
11:31 All field plane jumpers removed (Jumpers 1&3)
System wide checks ok
ASIC load check ok
11:37 DAQ started online only
Statistics - Attachment 6
FEE temperatures - Attachment 7
11:46 Layout 1 - Attachments 8 & 9
Layout 2 - attachments 10
13:38 Layouts 3 - Attachment 11
Layout 4 - Attachment 12
Pulser widths measured using 1.8.L spectra.
Most channels show an increase in noise with the FWHM increased by ~5-10 channels
(Recorded in log book)
13:55 Layout 7 p-side waveforms - Attachments 13 & 14
Layout 8 n-side waveforms - Attachments 15 & 16
For comparison with jumpers on see yesterday's elog entry: https://elog.ph.ed.ac.uk/AIDA/674
14:02 DAQ stopped
14:23 PCB ground plane jumper removed from all adapter boards (Jumper 2)
Bias and leakage currents ok T = 23.0 DP = +8.8 H = 38.7% - Attachment 17
System wide checks all ok
ASIC load check ok
DAQ Started
14:44 FEE temperatures all ok - Attachment 18
Statistics - Attachment 19
14:54 Layout 1 - Attachment 20 & 21
Layout 2 - Attachment 22
15:17 Layout 3 p-side pulser - Attachment 23
Layout 4 n-side pulser - Attachment 24
Pulser widths measured using 1.8.L spectra
In comparison with just having the FP jumpers removed for channels that were not noisy before they show no
to only minor increases in noise.
However channels that were previously noisy with all jumpers on show drastic increases in the amount of
noise. Increases in the FWHM of up to 80ch
13:55 Layout 7 p-side waveforms - Attachments 25 & 26
Layout 8 n-side waveforms - Attachments 27 & 28
DAQ Stopped
16:15 Detector bias turned off as replacing the jumpers is challenging
16:55 All jumpers back on. I advise starting with all on the new boards tomorrow and removing if needed.
Pain to put back on when mounted with cables.
16:59 System wide checks ok
Bias back on and leakage currents ok - Attachment 29
17:09 Statistics - Attachment 30
FEE temperatures - Attachment 31
By putting the jumpers back the statistics appear to have recovered to a similar level to this morning
17:25 FEEs powered down to do a power cycle for Patrick
17:50 FEEs powered up
18:00 Same javascript errors as yesterday when setting up DAQ
System wide checks all ok
FEE Temperatures ok
18:06 DAQ started
Statistics similar to before power cycle - Attachment 32
Layout 1 looks good - Attachments 33 & 34
18:14 DAQ stopped
18:16 DAQ Started
Writing to R2 in /TapeData/Oct17/
Writing at 11Mb/s
18:56 Statistics - Attachment 35 |
|
Thu Oct 19 11:32:29 2017, TD, OH, Thursday 19 October
|
>
> 09.40 DAQ continues OK
> File /TapeData/Oct17/R1_280
>
> BNC PB-4 Pulser frequency switched from 250Hz to 25Hz range
>
> 09:54 ASIC Temperatures - Attachment 1
> Bias and leakage currents ok - Attachments 2 & 3
> Statistics - Attachment 4
>
> 10:19 Output of analysis of R1_291 - Attachment 5
>
> 11:02 Pulser widths measured before changing jumpers (In log book)
> DAQ stopped on Run R1_304
>
> 11:31 All field plane jumpers removed (Jumpers 1&3)
> System wide checks ok
> ASIC load check ok
>
> 11:37 DAQ started online only
> Statistics - Attachment 6
> FEE temperatures - Attachment 7
>
> 11:46 Layout 1 - Attachments 8 & 9
> Layout 2 - attachments 10
>
> 13:38 Layouts 3 - Attachment 11
> Layout 4 - Attachment 12
> Pulser widths measured using 1.8.L spectra.
> Most channels show an increase in noise with the FWHM increased by ~5-10 channels
> (Recorded in log book)
>
> 13:55 Layout 7 p-side waveforms - Attachments 13 & 14
> Layout 8 n-side waveforms - Attachments 15 & 16
> For comparison with jumpers on see yesterday's elog entry: https://elog.ph.ed.ac.uk/AIDA/674
>
> 14:02 DAQ stopped
>
> 14:23 PCB ground plane jumper removed from all adapter boards (Jumper 2)
>
> Bias and leakage currents ok T = 23.0 DP = +8.8 H = 38.7% - Attachment 17
> System wide checks all ok
> ASIC load check ok
>
> DAQ Started
>
> 14:44 FEE temperatures all ok - Attachment 18
> Statistics - Attachment 19
>
> 14:54 Layout 1 - Attachment 20 & 21
> Layout 2 - Attachment 22
>
> 15:17 Layout 3 p-side pulser - Attachment 23
> Layout 4 n-side pulser - Attachment 24
>
> Pulser widths measured using 1.8.L spectra
>
> In comparison with just having the FP jumpers removed for channels that were not noisy before they show no
> to only minor increases in noise.
>
> However channels that were previously noisy with all jumpers on show drastic increases in the amount of
> noise. Increases in the FWHM of up to 80ch
>
> 13:55 Layout 7 p-side waveforms - Attachments 25 & 26
> Layout 8 n-side waveforms - Attachments 27 & 28
>
> DAQ Stopped
>
> 16:15 Detector bias turned off as replacing the jumpers is challenging
>
> 16:55 All jumpers back on. I advise starting with all on the new boards tomorrow and removing if needed.
> Pain to put back on when mounted with cables.
>
> 16:59 System wide checks ok
> Bias back on and leakage currents ok - Attachment 29
>
> 17:09 Statistics - Attachment 30
> FEE temperatures - Attachment 31
>
> By putting the jumpers back the statistics appear to have recovered to a similar level to this morning
>
> 17:25 FEEs powered down to do a power cycle for Patrick
>
> 17:50 FEEs powered up
>
> 18:00 Same javascript errors as yesterday when setting up DAQ
> System wide checks all ok
> FEE Temperatures ok
>
> 18:06 DAQ started
> Statistics similar to before power cycle - Attachment 32
> Layout 1 looks good - Attachments 33 & 34
>
> 18:14 DAQ stopped
>
> 18:16 DAQ Started
> Writing to R2 in /TapeData/Oct17/
> Writing at 11Mb/s
>
> 18:56 Statistics - Attachment 35
Please could you repeat the power cycle and this time turn all the FEE64s at once. The error I am looking to solve occurs ( so it is believed ) when all 24 request access to the server together. |
|
Wed Oct 18 03:57:37 2017, TD, OH, Wednesday 18 October 24x
|
11.57 Startup of AIDA following June 2017 shutdown
Julabo FL11006 ON, set point +20 deg C
Water flow indicators OK
Water level OK
Tektronix AFG3102C
Channel 2 - square wave, 50MHz, 180 deg, 0V offset, +5V amplitude
MACB root master - mode 5
Power up 24x FEE64s
aidas1:/var/log/messages
[root@aidas1 npg]# tail -f /var/log/messages
Oct 18 11:02:19 aidas1 dhcpd: DHCPACK on 10.1.1.117 to b8:27:eb:6b:0a:a0 (npg-monitor) via p2p1
Oct 18 11:02:21 aidas1 dhcpd: DHCPREQUEST for 10.1.1.114 from b8:27:eb:0b:f6:73 via p2p1
Oct 18 11:02:21 aidas1 dhcpd: DHCPACK on 10.1.1.114 to b8:27:eb:0b:f6:73 (raspberrypi) via p2p1
Oct 18 11:02:39 aidas1 dnsmasq[3260]: reading /etc/resolv.conf
Oct 18 11:02:39 aidas1 dnsmasq[3260]: using nameserver 10.32.0.1#53
Oct 18 11:06:59 aidas1 dhcpd: DHCPRELEASE of 10.1.1.114 from b8:27:eb:0b:f6:73 (raspberrypi) via p2p1 (found)
Oct 18 11:07:31 aidas1 dhcpd: DHCPDISCOVER from b8:27:eb:0b:f6:73 via p2p1
Oct 18 11:07:32 aidas1 dhcpd: DHCPOFFER on 10.1.1.114 to b8:27:eb:0b:f6:73 (raspberrypi) via p2p1
Oct 18 11:07:32 aidas1 dhcpd: DHCPREQUEST for 10.1.1.114 (10.1.1.250) from b8:27:eb:0b:f6:73 (raspberrypi) via p2p1
Oct 18 11:07:32 aidas1 dhcpd: DHCPACK on 10.1.1.114 to b8:27:eb:0b:f6:73 (raspberrypi) via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d4:b7 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.1.6 to 00:04:a3:2a:d4:b7 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.1.6 (10.1.1.250) from 00:04:a3:2a:d4:b7 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.1.6 to 00:04:a3:2a:d4:b7 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d9:e1 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.1.2 to 00:04:a3:2a:d9:e1 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.1.2 (10.1.1.250) from 00:04:a3:2a:d9:e1 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.1.2 to 00:04:a3:2a:d9:e1 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:9c:07 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.2.8 to 00:04:a3:2a:9c:07 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.2.8 (10.1.2.250) from 00:04:a3:2a:9c:07 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.2.8 to 00:04:a3:2a:9c:07 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:ed:b8 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.2.4 to 00:04:a3:2a:ed:b8 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d0:1b via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.1.1 to 00:04:a3:2a:d0:1b via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.2.4 (10.1.2.250) from 00:04:a3:2a:ed:b8 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.2.4 to 00:04:a3:2a:ed:b8 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.1.1 (10.1.1.250) from 00:04:a3:2a:d0:1b via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.1.1 to 00:04:a3:2a:d0:1b via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:b8:8d via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.2.7 to 00:04:a3:2a:b8:8d via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.2.7 (10.1.2.250) from 00:04:a3:2a:b8:8d via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.2.7 to 00:04:a3:2a:b8:8d via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:f7:06 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.2.3 to 00:04:a3:2a:f7:06 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.2.3 (10.1.2.250) from 00:04:a3:2a:f7:06 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.2.3 to 00:04:a3:2a:f7:06 via p2p2
Oct 18 11:29:36 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d0:10 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPOFFER on 10.1.1.5 to 00:04:a3:2a:d0:10 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPREQUEST for 10.1.1.5 (10.1.1.250) from 00:04:a3:2a:d0:10 via p2p1
Oct 18 11:29:36 aidas1 dhcpd: DHCPACK on 10.1.1.5 to 00:04:a3:2a:d0:10 via p2p1
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.6:915 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida6 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.2:1000 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida2 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.8:720 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida8 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.4:924 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida4 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.1:937 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida1 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.7:932 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida7 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.3:1008 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida3 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:36 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.5:911 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida5 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:f7:07 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.1.10 to 00:04:a3:2a:f7:07 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.1.10 (10.1.1.250) from 00:04:a3:2a:f7:07 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.1.10 to 00:04:a3:2a:f7:07 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d0:2f via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.2.12 to 00:04:a3:2a:d0:2f via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.2.12 (10.1.2.250) from 00:04:a3:2a:d0:2f via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.2.12 to 00:04:a3:2a:d0:2f via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:f3:ac via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.2.15 to 00:04:a3:2a:f3:ac via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:9c:0e via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.2.16 to 00:04:a3:2a:9c:0e via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.2.15 (10.1.2.250) from 00:04:a3:2a:f3:ac via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.2.15 to 00:04:a3:2a:f3:ac via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.2.16 (10.1.2.250) from 00:04:a3:2a:9c:0e via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.2.16 to 00:04:a3:2a:9c:0e via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d9:ad via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.1.9 to 00:04:a3:2a:d9:ad via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:11:b9 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.1.13 to 00:04:a3:2b:11:b9 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.1.9 (10.1.1.250) from 00:04:a3:2a:d9:ad via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.1.9 to 00:04:a3:2a:d9:ad via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.1.13 (10.1.1.250) from 00:04:a3:2b:11:b9 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.1.13 to 00:04:a3:2b:11:b9 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:11:af via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.2.11 to 00:04:a3:2b:11:af via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.2.11 (10.1.2.250) from 00:04:a3:2b:11:af via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.2.11 to 00:04:a3:2b:11:af via p2p2
Oct 18 11:29:49 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:11:b8 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPOFFER on 10.1.1.14 to 00:04:a3:2b:11:b8 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPREQUEST for 10.1.1.14 (10.1.1.250) from 00:04:a3:2b:11:b8 via p2p1
Oct 18 11:29:49 aidas1 dhcpd: DHCPACK on 10.1.1.14 to 00:04:a3:2b:11:b8 via p2p1
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.10:895 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida10 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.12:707 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida12 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.15:707 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida15 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.16:697 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida16 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.9:1012 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida9 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.13:711 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida13 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.11:835 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida11 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:29:49 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.14:997 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida14 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:24 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.2:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:31 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.4:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:32 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.7:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:32 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.6:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:33 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.1:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:33 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.8:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:34 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.3:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:f6:e9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.1.22 to 00:04:a3:2a:f6:e9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.1.22 (10.1.1.250) from 00:04:a3:2a:f6:e9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.1.22 to 00:04:a3:2a:f6:e9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d0:06 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.2.23 to 00:04:a3:2a:d0:06 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.2.23 (10.1.2.250) from 00:04:a3:2a:d0:06 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.2.23 to 00:04:a3:2a:d0:06 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:11:ae via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.1.18 to 00:04:a3:2b:11:ae via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:ed:b9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.1.17 to 00:04:a3:2a:ed:b9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.1.18 (10.1.1.250) from 00:04:a3:2b:11:ae via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.1.18 to 00:04:a3:2b:11:ae via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.1.17 (10.1.1.250) from 00:04:a3:2a:ed:b9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.1.17 to 00:04:a3:2a:ed:b9 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d0:11 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.2.20 to 00:04:a3:2a:d0:11 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.2.20 (10.1.2.250) from 00:04:a3:2a:d0:11 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.2.20 to 00:04:a3:2a:d0:11 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:27:54 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.2.19 to 00:04:a3:2b:27:54 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.2.19 (10.1.2.250) from 00:04:a3:2b:27:54 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.2.19 to 00:04:a3:2b:27:54 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2a:d9:b6 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.2.24 to 00:04:a3:2a:d9:b6 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.2.24 (10.1.2.250) from 00:04:a3:2a:d9:b6 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.2.24 to 00:04:a3:2a:d9:b6 via p2p2
Oct 18 11:30:37 aidas1 dhcpd: DHCPDISCOVER from 00:04:a3:2b:27:23 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPOFFER on 10.1.1.21 to 00:04:a3:2b:27:23 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPREQUEST for 10.1.1.21 (10.1.1.250) from 00:04:a3:2b:27:23 via p2p1
Oct 18 11:30:37 aidas1 dhcpd: DHCPACK on 10.1.1.21 to 00:04:a3:2b:27:23 via p2p1
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.5:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.22:973 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida22 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.23:881 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida23 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.17:825 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida17 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.18:784 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida18 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.20:898 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida20 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.19:968 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida19 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:37 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.24:795 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida24 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:30:38 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.21:715 for
/data10/XilinxLinux/ppc_4xx/rfs/nnaida21 (/data10/XilinxLinux/ppc_4xx/rfs)
Oct 18 11:31:09 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.15:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:10 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.10:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:10 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.9:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:11 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.12:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:11 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.13:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:11 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.14:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:11 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.16:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:31:11 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.11:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:04 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.22:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:04 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.20:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:04 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.17:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:06 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.24:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:06 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.23:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:06 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.18:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:07 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.2.19:864 for /MIDAS@aidas
(/MIDAS@aidas)
Oct 18 11:32:07 aidas1 rpc.mountd[2855]: authenticated mount request from 10.1.1.21:864 for /MIDAS@aidas
(/MIDAS@aidas)
nnaida24:/var/log/messages
Oct 18 04:31:50 nnaida24 syslogd 1.4.2: restart.
Oct 18 04:31:51 nnaida24 kernel: klogd 1.4.2, log source = /proc/kmsg started.
Oct 18 04:31:51 nnaida24 kernel: Using Xilinx Virtex440 machine description
Oct 18 04:31:51 nnaida24 kernel: Linux version 2.6.31 (nf@nnlxb.dl.ac.uk) (gcc version 4.2.2) #34 PREEMPT Tue
Nov 15 15:57:04 GMT 2011
Oct 18 04:31:51 nnaida24 kernel: Zone PFN ranges:
Oct 18 04:31:51 nnaida24 kernel: DMA 0x00000000 -> 0x00007000
Oct 18 04:31:51 nnaida24 kernel: Normal 0x00007000 -> 0x00007000
Oct 18 04:31:51 nnaida24 kernel: Movable zone start PFN for each node
Oct 18 04:31:51 nnaida24 kernel: early_node_map[1] active PFN ranges
Oct 18 04:31:52 nnaida24 kernel: 0: 0x00000000 -> 0x00007000
Oct 18 04:31:52 nnaida24 kernel: MMU: Allocated 1088 bytes of context maps for 255 contexts
Oct 18 04:31:52 nnaida24 kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 28448
Oct 18 04:31:52 nnaida24 kernel: Kernel command line: console=ttyS0 root=/dev/nfs ip=on rw mem=112M
Oct 18 04:31:52 nnaida24 kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Oct 18 04:31:52 nnaida24 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Oct 18 04:31:53 nnaida24 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Oct 18 04:31:53 nnaida24 kernel: Memory: 109680k/114688k available (3500k kernel code, 4852k reserved, 144k
data, 130k bss, 168k init)
Oct 18 04:31:53 nnaida24 kernel: Kernel virtual memory layout:
Oct 18 04:31:53 nnaida24 kernel: * 0xffffe000..0xfffff000 : fixmap
Oct 18 04:31:53 nnaida24 kernel: * 0xfde00000..0xfe000000 : consistent mem
Oct 18 04:31:53 nnaida24 kernel: * 0xfde00000..0xfde00000 : early ioremap
Oct 18 04:31:53 nnaida24 kernel: * 0xd1000000..0xfde00000 : vmalloc & ioremap
Oct 18 04:31:53 nnaida24 kernel: NR_IRQS:512
Oct 18 04:31:54 nnaida24 kernel: clocksource: timebase mult[a00000] shift[22] registered
Oct 18 04:31:54 nnaida24 kernel: Console: colour dummy device 80x25
Oct 18 04:31:54 nnaida24 kernel: Mount-cache hash table entries: 512
Oct 18 04:31:54 nnaida24 kernel: NET: Registered protocol family 16
Oct 18 04:31:54 nnaida24 kernel: PCI: Probing PCI hardware
Oct 18 04:31:54 nnaida24 kernel: bio: create slab <bio-0> at 0
Oct 18 04:31:54 nnaida24 kernel: NET: Registered protocol family 2
Oct 18 04:31:54 nnaida24 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Oct 18 04:31:54 nnaida24 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Oct 18 04:31:55 nnaida24 kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Oct 18 04:31:55 nnaida24 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Oct 18 04:31:55 nnaida24 kernel: TCP reno registered
Oct 18 04:31:55 nnaida24 kernel: NET: Registered protocol family 1
Oct 18 04:31:56 nnaida24 kernel: ROMFS MTD (C) 2007 Red Hat, Inc.
Oct 18 04:31:56 nnaida24 kernel: msgmni has been set to 214
Oct 18 04:31:56 nnaida24 kernel: io scheduler noop registered
Oct 18 04:31:57 nnaida24 kernel: io scheduler anticipatory registered
Oct 18 04:31:57 nnaida24 kernel: io scheduler deadline registered
Oct 18 04:31:58 nnaida24 kernel: io scheduler cfq registered (default)
Oct 18 04:31:58 nnaida24 kernel: Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Oct 18 04:31:58 nnaida24 kernel: 83e00000.serial: ttyS0 at MMIO 0x83e01003 (irq = 16) is a 16550
Oct 18 04:31:58 nnaida24 kernel: console [ttyS0] enabled
Oct 18 04:31:58 nnaida24 kernel: brd: module loaded
Oct 18 04:31:59 nnaida24 kernel: loop: module loaded
Oct 18 04:31:59 nnaida24 kernel: Device Tree Probing 'ethernet'
Oct 18 04:31:59 nnaida24 kernel: xilinx_lltemac 81c00000.ethernet: MAC address is now 0: 4:a3:2a:d9:b6
Oct 18 04:31:59 nnaida24 kernel: xilinx_lltemac 81c00000.ethernet: XLlTemac: using DMA mode.
Oct 18 04:31:59 nnaida24 kernel: XLlTemac: DCR address: 0x80
Oct 18 04:32:00 nnaida24 kernel: XLlTemac: buffer descriptor size: 32768 (0x8000)
Oct 18 04:32:00 nnaida24 kernel: XLlTemac: Allocating DMA descriptors with kmalloc
Oct 18 04:32:00 nnaida24 kernel: XLlTemac: (buffer_descriptor_init) phy: 0x6938000, virt: 0xc6938000, size: 0x8000
Oct 18 04:32:00 nnaida24 kernel: XTemac: PHY detected at address 7.
Oct 18 04:32:00 nnaida24 kernel: xilinx_lltemac 81c00000.ethernet: eth0: Xilinx TEMAC at 0x81C00000 mapped to
0xD1024000, irq=17
Oct 18 04:32:00 nnaida24 kernel: fc000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank
Oct 18 04:32:00 nnaida24 kernel: Intel/Sharp Extended Query Table at 0x010A
Oct 18 04:32:00 nnaida24 last message repeated 5 times
Oct 18 04:32:00 nnaida24 kernel: Using buffer write method
Oct 18 04:32:01 nnaida24 kernel: cfi_cmdset_0001: Erase suspend on write enabled
Oct 18 04:32:01 nnaida24 kernel: cmdlinepart partition parsing not available
Oct 18 04:32:02 nnaida24 kernel: RedBoot partition parsing not available
Oct 18 04:32:02 nnaida24 kernel: Creating 5 MTD partitions on "fc000000.flash":
Oct 18 04:32:02 nnaida24 kernel: 0x000000000000-0x000000500000 : "golden_firmware"
Oct 18 04:32:02 nnaida24 kernel: 0x000000500000-0x000000800000 : "golden_kernel"
Oct 18 04:32:02 nnaida24 kernel: 0x000000800000-0x000000d00000 : "user_firmware"
Oct 18 04:32:02 nnaida24 kernel: 0x000000d00000-0x000000fe0000 : "user_kernel"
Oct 18 04:32:02 nnaida24 kernel: 0x000000fe0000-0x000001000000 : "env_variables"
Oct 18 04:32:02 nnaida24 kernel: xilinx-xps-spi 81400400.hd-xps-spi: at 0x81400400 mapped to 0xD1028400, irq=20
Oct 18 04:32:03 nnaida24 kernel: SPI: XIlinx spi: bus number now 32766
Oct 18 04:32:03 nnaida24 kernel: xilinx-xps-spi 81400000.xps-spi: at 0x81400000 mapped to 0xD102C000, irq=21
Oct 18 04:32:03 nnaida24 rpcbind: cannot create socket for udp6
Oct 18 04:32:03 nnaida24 kernel: SPI: XIlinx spi: bus number now 32765
Oct 18 04:32:03 nnaida24 kernel: mice: PS/2 mouse device common for all mice
Oct 18 04:32:03 nnaida24 kernel: Device Tree Probing 'i2c'
Oct 18 04:32:03 nnaida24 kernel: #0 at 0x81600000 mapped to 0xD1030000, irq=22
Oct 18 04:32:04 nnaida24 kernel: at24 0-0050: 1024 byte 24c08 EEPROM (writable)
Oct 18 04:32:04 nnaida24 kernel: TCP cubic registered
Oct 18 04:32:04 nnaida24 kernel: NET: Registered protocol family 17
Oct 18 04:32:04 nnaida24 kernel: RPC: Registered udp transport module.
Oct 18 04:32:04 nnaida24 kernel: RPC: Registered tcp transport module.
Oct 18 04:32:05 nnaida24 kernel: eth0: XLlTemac: Options: 0x3fa
Oct 18 04:32:05 nnaida24 rpcbind: cannot create socket for tcp6
Oct 18 04:32:05 nnaida24 kernel: eth0: XLlTemac: allocating interrupt 19 for dma mode tx.
Oct 18 04:32:05 nnaida24 kernel: eth0: XLlTemac: allocating interrupt 18 for dma mode rx.
Oct 18 04:32:05 nnaida24 kernel: eth0: XLlTemac: speed set to 1000Mb/s
Oct 18 04:32:05 nnaida24 kernel: eth0: XLlTemac: Send Threshold = 24, Receive Threshold = 4
Oct 18 04:32:06 nnaida24 kernel: eth0: XLlTemac: Send Wait bound = 254, Receive Wait bound = 254
Oct 18 04:32:06 nnaida24 kernel: Sending DHCP requests ., OK
Oct 18 04:32:06 nnaida24 kernel: IP-Config: Got DHCP answer from 10.1.2.250, my address is 10.1.2.24
Oct 18 04:32:06 nnaida24 kernel: IP-Config: Complete:
Oct 18 04:32:06 nnaida24 kernel: device=eth0, addr=10.1.2.24, mask=255.255.255.0, gw=10.1.2.250,
Oct 18 04:32:06 nnaida24 kernel: host=nnaida24, domain=, nis-domain=(none),
Oct 18 04:32:06 nnaida24 kernel: bootserver=10.1.2.250, rootserver=10.1.2.250,
rootpath=/MIDAS@aidas/XilinxLinux/ppc_4xx/rfs/nnaida24,tcp
Oct 18 04:32:06 nnaida24 kernel: Looking up port of RPC 100003/2 on 10.1.2.250
Oct 18 04:32:06 nnaida24 kernel: Looking up port of RPC 100005/1 on 10.1.2.250
Oct 18 04:32:07 nnaida24 kernel: VFS: Mounted root (nfs filesystem) on device 0:12.
Oct 18 04:32:07 nnaida24 kernel: Freeing unused kernel memory: 168k init
Oct 18 04:32:10 nnaida24 xinetd[275]: IPv6 socket creation failed for service telnet, trying IPv4
Oct 18 04:32:10 nnaida24 xinetd[275]: IPv6 socket creation failed for service ftp, trying IPv4
Oct 18 04:32:10 nnaida24 xinetd[275]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in.
Oct 18 04:32:11 nnaida24 xinetd[275]: Started working: 2 available services
Oct 18 04:32:16 nnaida24 kernel: Trying to free nonexistent resource <0000000081000000-00000000811fffff>
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: mem region start 0x81000000 for 0x200000 mapped at 0xd2100000
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: driver assigned major number 254
Oct 18 04:32:22 nnaida24 kernel: Trying to free nonexistent resource <0000000007000000-0000000007ffffff>
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: mem region start 0x7000000 for 0x1000000 mapped at 0xd2380000
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: driver assigned major number 253
Oct 18 04:32:38 nnaida24 kernel: XAIDA: xaida_open:
Oct 18 04:32:38 nnaida24 kernel: AIDAMEM: aidamem_open:
Oct 18 04:43:16 nnaida24 xinetd[275]: START: telnet pid=395 from=10.1.2.250
-bash-3.2# tail messages
Oct 18 04:32:11 nnaida24 xinetd[275]: Started working: 2 available services
Oct 18 04:32:16 nnaida24 kernel: Trying to free nonexistent resource <0000000081000000-00000000811fffff>
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: mem region start 0x81000000 for 0x200000 mapped at 0xd2100000
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: driver assigned major number 254
Oct 18 04:32:22 nnaida24 kernel: Trying to free nonexistent resource <0000000007000000-0000000007ffffff>
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: mem region start 0x7000000 for 0x1000000 mapped at 0xd2380000
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: driver assigned major number 253
Oct 18 04:32:38 nnaida24 kernel: XAIDA: xaida_open:
Oct 18 04:32:38 nnaida24 kernel: AIDAMEM: aidamem_open:
Oct 18 04:43:16 nnaida24 xinetd[275]: START: telnet pid=395 from=10.1.2.250
-bash-3.2# tail messages
Oct 18 04:32:16 nnaida24 kernel: Trying to free nonexistent resource <0000000081000000-00000000811fffff>
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: mem region start 0x81000000 for 0x200000 mapped at 0xd2100000
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: driver assigned major number 254
Oct 18 04:32:22 nnaida24 kernel: Trying to free nonexistent resource <0000000007000000-0000000007ffffff>
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: mem region start 0x7000000 for 0x1000000 mapped at 0xd2380000
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: driver assigned major number 253
Oct 18 04:32:38 nnaida24 kernel: XAIDA: xaida_open:
Oct 18 04:32:38 nnaida24 kernel: AIDAMEM: aidamem_open:
Oct 18 04:43:16 nnaida24 xinetd[275]: START: telnet pid=395 from=10.1.2.250
Oct 18 04:52:07 nnaida24 kernel: XAIDA: xaida_open:
-bash-3.2# tail messages
Oct 18 04:32:16 nnaida24 kernel: Trying to free nonexistent resource <0000000081000000-00000000811fffff>
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: mem region start 0x81000000 for 0x200000 mapped at 0xd2100000
Oct 18 04:32:16 nnaida24 kernel: XAIDA: xaida: driver assigned major number 254
Oct 18 04:32:22 nnaida24 kernel: Trying to free nonexistent resource <0000000007000000-0000000007ffffff>
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: mem region start 0x7000000 for 0x1000000 mapped at 0xd2380000
Oct 18 04:32:22 nnaida24 kernel: AIDAMEM: aidamem: driver assigned major number 253
Oct 18 04:32:38 nnaida24 kernel: XAIDA: xaida_open:
Oct 18 04:32:38 nnaida24 kernel: AIDAMEM: aidamem_open:
Oct 18 04:43:16 nnaida24 xinetd[275]: START: telnet pid=395 from=10.1.2.250
Oct 18 04:52:07 nnaida24 kernel: XAIDA: xaida_open:
Pi monitor browser - see attachment 1 - 24x FEE64 'not finished'
Start httpd for data acquisition, start web browser for AIDA DAQ
DAQ RESET and SETUP produce pop up messages - see attachments 2 & 3
Manual ReSYNC required
All system wide checks OK
*except* synchronise ASIC clocks which fails for *all* FEE64s
which may be correct for current firmware synchronising FEE64 clock and ASIC readout clock - to be checked
12.11 No FEE64 temperatures - see attachment 4
12.14 Detector bias and leakage currents OK - see attachments 5 & 6
Ambient temperature +23.1 deg C, d.p. +8.0 deg C, RH 38%
12.20 By hand, the temperatures of the FEE64 mezzanines feel OK
13:50 By hand, the temperatures of the FEE64 mezzanines still feel OK
13:53 FEE64 Temperature displays back online see attachment 7
13:58 System wide checks ok
14:00 Pulser had been switched off. Turned on, amplitude at 90000, Frequency set to 25Hz scale
14:04 ASIC load check ok
14:20 Statistics with pulser running. All reasonable though nnaida13 about double the rest. - Attachment 8
14:45 Pulser widths taken using 1.8.L spectra - attachments 9 & 10
Crane was running whilst pulser peaks were forming
15:00 Waveforms for p and n sides - attachments 11 - 14
For comparisons for stats and waveforms see elog entry https://elog.ph.ed.ac.uk/AIDA/668
16:32 DAQ started writing to file in /TapeData/Oct17 with R1_0
16:41 Layouts 1 and 2 - attachments 15-17
17:30 Analysis of R1_7 - attachment 18
17:40 Spectra of ADC data items /s and DSSD rates as a function of time - attachments 18 & 19 respectively
17:57 Bias and leakage currents ok - attachment 24
System wide checks ok though nnaida24 has about 9000kb less memory
System left running
18:13 Pulser event in lec data plot - attachments 20 & 21
Discriminator spectra - attachment 22 |
|