10:18 Leakage and bias ok - Attachment 1
      FEE temperatures ok - Attachment 2
      Statistics - Attachment 3
      DAQ continues ok

10:23 DAQ stopped on R7_10
      Alpha run through night

10:28 MIDAS Sort spectra from the alpha run
      Ep versus En - Attachment 4
      x versus y 2D hit pattern - Attachment 5
      Front versus back multiplicity - Attachment 6

      2D Hit pattern indicates detection of alphas in all 4 regions of each of the 6 detectors
      indicates cabling is ok

11:55 FEEs turned off after being unable to recover after crash

13:49 FEEs powered on again
      Pi monitor indicates panic on nnaida22 the FEE that crashed

      ReSync done on setup except for 23 and 24
      Master ReSync done succesfully
      ASIC settings loaded default to 2017Mar27
      Restoring 2017Oct22
      
      System wide checks ok
      Leakage and bias ok - Attachment 7
      FEE temperatures crashed - Attachment 8

      Upon reboot all rates across the FEEs appear lower
      In particular 13 and 14. Thresholds have been reduced back to 0xa for all ASICs on both FEEs

      Layout 1 linear common y of 2000 - Attachment 9
      Layout 1 log common y of 10 - Attachment 10

      All front side FEE64 1.8.W waveforms - 20us range - Attachment 11
      All back side FEE64 1.8.W waveforms - 20us range - Attachment 12

      All front side FEE64 1.8.W waveforms - 2ms range - Attachment 13
      All back side FEE64 1.8.W waveforms - 2m range - Attachment 14

      FEE64 nnaida13 1.*.W waveforms - Ibias LF 0xf - 2ms range - Attachment 15

      Statistics after switch and thresholds lowered - Attachment 16
      Pulser widths measured. On boards changed 10 out of 12 FEEs show greater than 10% improvements
      11 out of 24 total show greater than 10%
      FEE stats post pulser width - Attachment 17

      New ASIC settings DB key: 2017Oct23-14.38.03
      Slow comparator 0xa for all FEE64s and all ASICs
      IBias LF feedback at 0xf for all front side FEEs except nnaida 2 which is at 0xc
      IBias LF feedback at 0xb for all back side FEEs
      ASIC settings DB file checked OK

      Ambient temperature +23.3 deg C, D.P +7.1 deg C,  R.H. 35.2%
      Julabo FL11006 set point +20.0 deg C, water le

15:38 Merger and TapeServer screenshots - Attachments 17-18
      

> 10:18 Leakage and bias ok - Attachment 1
>       FEE temperatures ok - Attachment 2
>       Statistics - Attachment 3
>       DAQ continues ok
> 
> 10:23 DAQ stopped on R7_10
>       Alpha run through night
> 
> 10:28 MIDAS Sort spectra from the alpha run
>       Ep versus En - Attachment 4
>       x versus y 2D hit pattern - Attachment 5
>       Front versus back multiplicity - Attachment 6
> 
>       2D Hit pattern indicates detection of alphas in all 4 regions of each of the 6 detectors
>       indicates cabling is ok
> 
> 11:55 FEEs turned off after being unable to recover after crash
Please could you define this 'crash' to allow a better understanding of problems with the system. 
For example.... what is unresponsive.... does a parse of the FEE64 log files ( before doing anything ) reveal a panic that is new? Does a STOP of the Tape work ? Does a Toggle of the MERGE pause state 
work ? 
Thus it will be possible to say that ..... FEE # is always the one responsible for DAQ failure or by < ???? > or the MERGE has found < ??? > problem.
Thanks in advance ;-)))

> 
> 13:49 FEEs powered on again
>       Pi monitor indicates panic on nnaida22 the FEE that crashed
> 
>       ReSync done on setup except for 23 and 24
>       Master ReSync done succesfully
>       ASIC settings loaded default to 2017Mar27
>       Restoring 2017Oct22
>       
>       System wide checks ok
>       Leakage and bias ok - Attachment 7
>       FEE temperatures crashed - Attachment 8
> 
>       Upon reboot all rates across the FEEs appear lower
>       In particular 13 and 14. Thresholds have been reduced back to 0xa for all ASICs on both FEEs
> 
>       Layout 1 linear common y of 2000 - Attachment 9
>       Layout 1 log common y of 10 - Attachment 10
> 
>       All front side FEE64 1.8.W waveforms - 20us range - Attachment 11
>       All back side FEE64 1.8.W waveforms - 20us range - Attachment 12
> 
>       All front side FEE64 1.8.W waveforms - 2ms range - Attachment 13
>       All back side FEE64 1.8.W waveforms - 2m range - Attachment 14
> 
>       FEE64 nnaida13 1.*.W waveforms - Ibias LF 0xf - 2ms range - Attachment 15
> 
>       Statistics after switch and thresholds lowered - Attachment 16
>       Pulser widths measured. On boards changed 10 out of 12 FEEs show greater than 10% improvements
>       11 out of 24 total show greater than 10%
>       FEE stats post pulser width - Attachment 17
> 
>       New ASIC settings DB key: 2017Oct23-14.38.03
>       Slow comparator 0xa for all FEE64s and all ASICs
>       IBias LF feedback at 0xf for all front side FEEs except nnaida 2 which is at 0xc
>       IBias LF feedback at 0xb for all back side FEEs
>       ASIC settings DB file checked OK
> 
>       Ambient temperature +23.3 deg C, D.P +7.1 deg C,  R.H. 35.2%
>       Julabo FL11006 set point +20.0 deg C, water le
> 
> 15:38 Merger and TapeServer screenshots - Attachments 17-18
>       

11.16 DAQ continues
      AIDA file Oct17/R8_107

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03

11.20 Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      good events statistics stable & OK - see attachments 4 & 5
      no merger/tapeserver errors reported since start of run - see attachments 6 & 7
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

11.30 Ambient temperature +23.3 deg C, d.p. +4.1 deg C, RH 28.7%

11.30 analysis file Oct17/R7_108 - zero deadtime, 6x MBS and zero ts timewarps - see attachment 8

11.39 DAQ stop

11.44 DAQ start
      AIDA file Oct17/R9

      Pulser walkthrough

      BNC PB-4
      Amplitude 90,000-10,000 @ 10,000 step
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 250Hz
      delay MIN, tail pulse, INT ref

11.53 DAQ stop
      See attachment 8

11.44 DAQ start
      AIDA file Oct17/R10

      Pulser walkthrough

      BNC PB-4
      Amplitude 12,000-2,000 @ 2,000 step
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 250Hz
      delay MIN, tail pulse, INT ref

11.53 DAQ stop
      See attachment 9

12.06 DAQ starts
      AIDA file Oct17/R12

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03

14.41 online analysis 
      ADC synchronised - see attachment 10


17.12 DAQ starts
      AIDA file Oct17/R13

      Background for LuckyDoll automatic threshold determination

      BNC PB-4 OFF

      ASIC settings 2017Oct23-14.38.03
      Slow comparator nnaida13 0xc, nnaida19-22 0xb, all other FEE64s 0xa

      DAQ statistics - see attachment 11

17.27 DAQ stop
      
18.03 DAQ starts
      AIDA file Oct17/R16

      Background for LuckyDoll automatic threshold determination

      BNC PB-4 OFF

      ASIC settings 2017Oct23-14.38.03
      Slow comparator *all* FEE64s 0xa

      DAQ statistics - see attachment 12

18.22 DAQ stop

18.48 DAQ statistics
      Slow comparator *all* FEE64s 0xa - see attachment 13
      Slow comparator *all* FEE64s 0x9 - see attachment 14
      Slow comparator *all* FEE64s 0x8 - see attachment 15
      Slow comparator *all* FEE64s 0x7 - see attachment 16

18.53 Detector biases & leakage currents OK - see attachments 13 & 14
      FEE64 Temperatures OK - see attachment 15
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

11.27 DAQ continues
      Not writing to disk

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      good events statistics stable & OK - see attachments 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

11.47 Ambient temperature +23.9 deg C, d.p. +9.0 deg C, RH 39.0%

16:45 System wide checks all ok 
      FEE temps ok - Attachment 5
      Stats - Attachment 6
      Bias and leakage ok - Attachment 7

02.37 DAQ stalled - USB-controlled ac mains relay fuse blown
      Not writing to disk

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa

      Detector biases & leakage currents OK - see attachments 1 & 2
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Ambient temperature +24.3 deg C, d.p. +8.7 deg C, RH 37.1%

02.54 Replace 250V/16A fuse and power up

      FEE64 Temperatures OK - see attachment 3
      good events statistics stable & OK - see attachments 4

03:30 Stats with nnaida13 slow comparator threshold raised to 140keV - Attachment 5

03:50 Pulser widths done, slow comparator threshold raised to 0xc ~120keV for  nnaida 19-22
      Statistics - Attachment 6

05:40 Beam now going into F11. Wasabi and YSol in front of AIDA
      AIDA is seeing light particles
      Waveforms look good
      Layout 7 - Attachment 7
      layout 8 - Attachment 8
      Statistics with light particles going through - Attachment 9
      Bias and leakage currents ok - Attachment 10

      We are taking the light ion data to file in R17_*

06:50 Light ion data continues
      System wide checks all ok

07:22 Bias and leakage ok - Attachment 11
      FEE Temperatures ok - Attachment 12
      Stats - Attachment 13

08:15 Light ions stop still writing file

08:27 Beam into aida run R17_30
      Zero degrader, just 4mm of WAS3ABI
      WAS3ABI run 120
      BRIKEN started run at 08:27 run 18
      BIGRIPS Run 8
      Timestamp reset at 08:27
      Stats with beam - Attachment 14

08:44 Waveforms with implants in the detector
      Layout 7 - Attachments 15 & 16
      Layout 8 - Attachments 17 & 18
      Layout 1  linear and log attachments 19 & 20 
      Leakage and bias ok - Attachment 21

09:14 Just noticed the stats in nnaida13 has dropped rate. Noise source may have been turned off
      Statistics - Attachment 22

      Spectra from the 0mm degrader run - Attachments 22-27

09:20 BRIKEN and WAS3ABI stop on run 162 aida on R17_35
      1mm degrader moved in
      BigRIPS on run 9
      BRIKEN run 19
      WAS3ABI start on 163
      AIDA on R17_35

      Rates similar to last screenshot of stats 09:14

09:26 Leakage and bias ok - Attachment 28

09:41 Beam stops
      AIDA on file R17_37
      BRIKEN stops running
      WAS3ABI on run 178

AIDA Files written
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:22 R17_29
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:31 R17_30
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:40 R17_31
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 08:50 R17_32
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:00 R17_33
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:10 R17_34
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:21 R17_35
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:31 R17_36
-rw-rw-rw-. 1 npg npgstaff 2.0G Oct 26 09:42 R17_37
-rw-rw-rw-. 1 npg npgstaff 329M Oct 26 09:44 R17_38

09.56 DAQ stopped OK yesterday

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Julabo FL11006 recirculating chiller coolant reservoir refilled - set point +20 deg C, actual +20.0 deg C
      Ambient temperature +23.6 deg C, d.p. +6.2 deg C, RH 32.2%

      AIDA withdrawn from (CH2)n matrix

      DAQ started - no data transfer
      good events statistics stable - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

13:30 System wide checks ok
      Stats - Attachment 6
      FEE temperatures ok - Attachment 7
      leakage and bias ok - Attachment 8

17.15 Detector biases & leakage currents OK - see attachments 9 & 10
      FEE64 Temperatures OK - see attachment 11
      good events statistics stable - see attachment 12
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Ambient temperature +25.2 deg C, d.p. +5.7 deg C, RH 28.5%

Offline analysis of High Energy Channel (HEC) 20GeV FSR data from AIDA data file Oct17/R17_31-R17_34

Degrader OUT

Attachment 1 - per DSSSD #1-6 m_p versus m_n
Attachment 2 - 2D spectra contour levels/colours
Attachment 3 - per DSSSD #1-6 x versus y 
Attachment 4 - per DSSSD #1-6 E_p versus E_n (20MeV/channel nominal)

Attachments 5-7 - as above but with all statistics from AIDA data files Oct17/R17_34

Attachment 8 - Sum of E_p energies for DSSSD #1-6 (5.6MeV/channel nominal)

               Peak at channel 1450 corresponds to an energy of 8.1GeV
               End of spectrum channel 1850 corresponds to 10.4GeV

               Note - HEC data not gain-matched
                      Using nominal HEC calibration accurate to ~ +/-20%

               

11.33 DAQ running OK - date transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C
      Ambient temperature +26.2 deg C, d.p. +6.2 deg C, RH 28.3%

14.40 Detector biases & leakage currents OK - see attachments 5 & 6
      FEE64 Temperatures OK - see attachment 7
      DAQ statistics OK - see attachment 8
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

14.50 DAQ starts
      AIDA data file Oct17/R18

14.53 per FEE64 rates (20us/channel) - see attachment 9
      No indication of c. 400us period noise as indicated by DAQ statistics attachment 8

15.46 DAQ stopped

      DAQ start - data tranfser disabled

19.40 Detector biases & leakage currents OK - see attachments 10 & 11
      FEE64 Temperatures OK - see attachment 12
      DAQ statistics OK - see attachment 13
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

For comparison with waveforms shown in https://elog.ph.ed.ac.uk/AIDA/665 and https://elog.ph.ed.ac.uk/AIDA/668

Note; nnaida21 ADC did not calibrate during setup therefore no waveforms for this FEE64

Current configuration

p+n junction strips FEE64 adaptor PCB rev D -> FEE64 adaptor PCB rev E
ac coupling 10n/100V/X7R -> 33n/100V/X7R
detector bias RC filter 3.3k/10n added
ASIC setting Ibias LF feedback 0x8 -> 0xf *except* nnaida2 ->0xc

n+n ohmic strips FEE64 adaptor PCB rev C *no change*
ASIC setting Ibias LF feedback 0xb *no change*


Attachments 1-5 waveforms for n+n ohmic strips

Attachment 1 - per FEE64 1.8.W, 20us range
Attachment 2 - per FEE64 1.8.W, 20us range, expanded y=scale
Attachment 3 - per FEE64 1.8.W, 200us range, expanded y=scale
Attachment 4 - per FEE64 1.8.W, 2ms range, expanded y=scale
Attachment 5 - per FEE64 1.8.W, 20ms range, expanded y=scale

Attachments 6-10 waveforms for p+n junction strips

Attachment 6 - per FEE64 1.8.W, 20us range
Attachment 7 - per FEE64 1.8.W, 20us range, expanded y=scale
Attachment 8 - per FEE64 1.8.W, 200us range, expanded y=scale
Attachment 9 - per FEE64 1.8.W, 2ms range, expanded y=scale
Attachment 10 - per FEE64 1.8.W, 20ms range, expanded y=scale

14.16 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C
      Ambient temperature +23.9 deg C, d.p. +10.8 deg C, RH 43.2%

15.05 per FEE64 Rate, 1.8.L and 1.8.W spectra - note common x & y scales
      Peak width nnaida5 63 ch FWHM
      Peak width nnaida8 82 ch FWHM

15.09 All histograms zero'd

18.25 Detector biases & leakage currents OK - see attachments 11 & 12
      FEE64 Temperatures OK - see attachment 13
      DAQ statistics OK - see attachment 14
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

10.10 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

15.56 Detector biases & leakage currents OK - see attachments 5 & 6
      FEE64 Temperatures OK - see attachment 7
      DAQ statistics OK - see attachment 8
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

09.34 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

15.02 Detector biases & leakage currents OK - see attachments 5 & 6
      FEE64 Temperatures OK - see attachment 7
      DAQ statistics OK - see attachment 8
      *all* system wide checks OK *except* nnaida21 fails ADC calibration
      Ambient temperature +24.3 deg C, d.p. -0.2 deg C, RH 19.8%
      Julabo FL11006 recirculating chiller set point +20 deg C, actual +20.0 deg C, water level OK c. mid-point
middle-upper marker
     

Offline analysis of the AIDA Oct17/R17_31 to R17_34 data "84Ge setting"
compared to an equivalent analysis of the AIDA RIBF128/R5_124 to R5_148
data from the 130Ag setting of the June 2017 RIBF128 experiment.

N.B. 
1) no software thresholds
2) no PID correlation
3) unless otherwise stated, all implant energies are the stopping layer implant energies

Attachment 1 - implantation energy (20MeV/ch, range 20.48GeV)
               versus
               per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)

               The 130Ag data (lower) clearly shows the "20ms bump", there is no
               evidence for a "20ms bump" in the "84Ge" data (upper).

               Note the non-observation of the "20ms bump" in the "84Ge" data
               is not explained by the larger range of implant energies of the
               130Ag data ( see attachment 7 )
               
Attachments 2-3 - per pixel implant-decay times (163.84us/ch)

                  upper 130Ag setting
                  lower "84Ge setting"

Attachments 4-5 - per pixel implant-decay times (163.84us/ch)

                  red 130Ag setting
                  yellow "84Ge setting"

Attachment 6 - *total* implant energy for AIDA DSSSD stack (5.6MeV/channel)

               yellow 130Ag setting
               red "84Ge setting"

Attachment 7 - implant energy for stopping DSSSD layer (20MeV/channel)

               red 130Ag setting
               yellow "84Ge setting"

Attachment 8 - per pixel decay-decay correlation time (163.84us/ch, range 16.78ms)
               versus
               per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)

               upper "84Ge setting"
               lower 130Ag setting

Attachment 9 - x and y-axis projections for 130Ag setting spectrum

               @x per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
               @y per pixel decay-decay correlation time (163.84us/ch, range 16.78ms)

Attachment 10 - x and y-axis projections for "84Ge setting" setting spectrum

               @x per pixel implant-decay correlation time (163.84us/ch, range 16.78ms)
               @y per pixel decay-decay correlation time (163.84us/ch, range 16.78ms)

11:24 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1
      FEE64 Temperatures OK - see attachment 2
      DAQ statistics OK - see attachment 3
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

10.56 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida13 0xe, nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

      p+n FEE64s 1.8.L spectra - see attachment 5 - nnaida17 FWHM 63 ch
      n+n FEE64s 1.8.L spectra - see attachment 6 - nnaida3 FWHM 78 ch
      per FEE64 rate spectra - see attachments 7 & 8

11.06 all spectra zero'd

17.28 Detector biases & leakage currents OK - see attachments 9 & 10
      FEE64 Temperatures OK - see attachment 11
      DAQ statistics OK - see attachment 12
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

18.46 per PJCS request two screenshots of nnaida21:8015/AIDA/MONLOCK/MONLOCK.tml
      see attachments 13 & 14

23:52 Statistics still good - Attachment 15
      Leakage and bias ok - Attachment 16

10.56 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1
      FEE64 Temperatures OK - see attachment 2
      DAQ statistics OK - see attachment 3
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

08.09 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1 & 2
      FEE64 Temperatures OK - see attachment 3
      DAQ statistics OK - see attachment 4
      *all* system wide checks OK *except* nnaida21 fails ADC calibration - see attachment 6
      PLL and DCM Clock Lock Monitor OK - see attachment 5

08.22 per FEE64 Rate, 1.8.L and 1.8.W spectra - see attachments 7-12
      nnaida3 78 ch FWHM
      nnaida17 66 ch FWHM

16.43 Detector biases & leakage currents OK - see attachments 13 & 14
      FEE64 Temperatures OK - see attachment 15
      DAQ statistics OK - see attachment 16
      *all* system wide checks OK *except* nnaida21 fails ADC calibration - see attachment 6
      PLL and DCM Clock Lock Monitor OK - see attachment 5

      per FEE64 Rate, 1.8.L pectra - see attachments 17-20
      nnaida3 78 ch FWHM
      nnaida17 68 ch FWHM

08.09 DAQ running OK - data transfer not enabled

      BNC PB-4
      Amplitude 90,000
      x5 attenuator IN
      t_r 100ns tau_d 50us
      - polarity
      frequency range 25Hz
      delay MIN, tail pulse, INT ref

      ASIC settings 2017Oct23-14.38.03
      *all* FEE64s slow comparators 0xa *except* nnaida19-22 0xc

      Detector biases & leakage currents OK - see attachments 1
      FEE64 Temperatures OK - see attachment 2
      DAQ statistics OK - see attachment 3
      *all* system wide checks OK *except* nnaida21 fails ADC calibration

13:35 DAQ running ok
      Fee temperatures - attachment 4
      Stats - attachment 5
      Leakage currents and bias ok - Attachment 6

13:39 Bias taken off detectors
      Server windows closed and servers halted
      FEE power relays turned off
      Chiller remains on

12:32 Chiller found almost empty & still working at 20C. Refilled to overflow.